OPA699ID - 1 GHz Voltage-Limiting Op Amp | Texas Instruments
部品番号: OPA699ID ✓ 生産中OPA699ID 概要
An operational amplifier is a voltage-feedback amplifier that uses negative feedback to amplify the difference between its differential inputs. The OPA699 belongs to the high-speed voltage-feedback amplifier family, which sits within the broader linear amplifier and analog IC hierarchy. Unlike a general-purpose precision amplifier, this device combines a wideband signal path with built-in bipolar output limiting, providing a deliberate boundary for output swing without relying entirely on external clamp networks.
Principal performance features include a 1 GHz gain-bandwidth product, a 260 MHz -3 dB bandwidth, and a minimum stable noise gain of +4. The amplifier can deliver output current up to 120 mA, while its output may swing to within approximately 1 V of each supply rail. The limiter has an accuracy of ±10 mV and recovers from overdrive in 1 ns. These characteristics are particularly useful when a fast signal must reach an analog-to-digital converter without allowing large transient or sustained overdrive to damage the input stage.
The OPA699ID operates from single-supply voltages of 5 V to 12 V or split supplies equivalent to ±2.5 V to ±6 V. Its wideband architecture prioritizes fast signal propagation and large-signal slew performance. Because the amplifier is stable only at gains of +4 or higher, closed-loop feedback must be arranged with sufficient attenuation; operation near unity gain can produce instability and ringing. Input bias current is approximately 3 µA, input offset voltage is approximately 1.5 mV, and typical supply current is 15.5 mA per channel.
Typical applications include high-speed ADC input conditioning, video and test-instrumentation signal chains, communications equipment, and active filtering where wide bandwidth is needed. The limiter can protect a downstream ADC input when an upstream transition produces excessive amplitude, while the 1 ns recovery characteristic helps the amplifier return to linear operation quickly after an overload event. Short trace lengths and careful grounding remain essential because the 260 MHz bandwidth can expose board-level parasitics and impedance discontinuities.
When laying out the circuit, place input, feedback, and supply-bypass connections close to the device and use a low-inductance ground return. Keep feedback-loop geometry compact to minimize parasitic inductance and maintain stable gain. Confirm the output-current demand, supply headroom, and ADC input range before relying on the limiter as the final protection mechanism.
This page combines the OPA699ID electrical characteristics, manufacturer documentation, package details, drop-in alternatives, and practical layout guidance into a focused engineering reference. It also distinguishes exact sourcing parameters from design-specific recommendations so engineers can evaluate the amplifier in ADC interfaces and other bandwidth-sensitive analog systems.
ドロップイン代替品: OPA699ID — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: OPA699ID (同一形状・フットプリント) — 相違点: -3 dB Bandwidth, Gain-Bandwidth Product, Slew Rate.
OPA699IDG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
OPA699IDRG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
OPA699UID
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
OPA699UIDG4
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
OPA699ID 最大定格&電気的特性
| Number of Channels | 1 channel |
| Amplifier Type | Voltage-feedback operational amplifier |
| Gain-Bandwidth Product | 1000 MHz |
| -3 dB Bandwidth | 260 MHz |
| Slew Rate | 1400 V/µs |
| Minimum Stable Gain | +4 V/V |
| Output Current | 120 mA |
| Output Swing Limit | Approximately 1 V from each supply rail |
| Limiting Voltage Accuracy | ±10 mV |
| Overdrive Recovery Time | 1 ns |
| Total Supply Voltage Range | 5 V to 12 V |
| Split-Supply Operating Range | ±2.5 V to ±6 V |
| Input Bias Current | 3 µA |
| Input Offset Voltage | 1.5 mV |
| Supply Current per Channel | 15.5 mA |
| 動作温度範囲 | -40°C to +85°C |
| パッケージ | 8-pin SOIC (D), 3.90 mm width |
| 実装タイプ | Surface mount |
OPA699ID 8-pin soic (d), 3.90 mm width ピン配置ガイド
OPA699ID (8-pin soic (d), 3.90 mm width パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA699ID.
詳細は データシート をご参照ください。
主な用途
OPA699ID の用途: 6 件s: High-Speed ADC Input Conditioning, Video and Communications Signal Chains, Test and Measurement Instrumentation, Active Filtering and Frequency Response, Pulse and Digital-to-Analog Edge Conditioning, Industrial Control and Sensor Signal Paths.
High-Speed ADC Input Conditioning
The OPA699ID fits between a fast analog source and a high-speed ADC because its 260 MHz -3 dB bandwidth preserves signal amplitude across a wide frequency range and its 1400 V/µs slew rate supports large full-scale transitions. The integrated bipolar limiter constrains output swing to approximately 1 V from each rail and provides ±10 mV limiting accuracy, helping protect the ADC input from an excessive transient. Configure the feedback network for noise gain of +4 or higher, then verify settling time against the ADC acquisition requirement. Because the limiter recovers in 1 ns, the amplifier can return rapidly to linear operation after a short overload.
おすすめ
Video and Communications Signal Chains
OPA699ID is appropriate for wideband communications and video circuitry requiring rapid edge delivery without sacrificing overload control. Its 1 GHz gain-bandwidth product and 260 MHz -3 dB bandwidth support wideband amplification, while the 1400 V/µs slew rate reduces distortion on square-wave and video-rate transitions. The bipolar output limiter helps prevent an unexpected upstream signal from driving the output deeply into saturation. Keep the closed-loop noise gain at +4 or higher and place feedback components close to the amplifier, because board parasitics become increasingly significant as signal bandwidth approaches the device's upper operating range.
おすすめ
Test and Measurement Instrumentation
The OPA699ID can serve as a high-bandwidth buffer or gain stage in measurement equipment where fast recovery after an input overload is valuable. Its 1 ns recovery behavior helps minimize the interval during which the output remains distorted after clipping, and the ±10 mV limiter accuracy gives the circuit a defined output boundary. For instrumentation, evaluate the approximately 1.5 mV input offset and 3 µA bias current against the complete measurement error budget. Stable operation at gain +4 or higher also makes the device suitable for attenuating input networks feeding a high-speed measurement stage.
おすすめ
Active Filtering and Frequency Response
OPA699ID can implement active filters and frequency-shaping stages in systems where the 260 MHz -3 dB bandwidth provides useful operating margin. Its 1400 V/µs slew rate reduces slew-induced distortion in filter passbands, while the 1 GHz gain-bandwidth product supports higher-order active-filter designs. The amplifier must remain at or above a +4 noise gain, which means the passive feedback network must deliberately establish that gain rather than relying on unity-gain buffering. Use short, shielded feedback routes and verify component parasitic effects because the wideband amplifier can amplify board-level feedback as well as the intended signal.
おすすめ
Pulse and Digital-to-Analog Edge Conditioning
OPA699ID is useful in pulse-shaping and data-converter output-conditioning circuits because its high slew rate preserves rapid transitions and its limiter limits amplitude during unexpected excursions. A 260 MHz -3 dB bandwidth covers many edge-sensitive analog stages, while the approximately ±10 mV limiter accuracy defines the peak output level more tightly than a passive clamp alone. The 1 ns overload recovery is especially useful when a pulse train temporarily exceeds the intended range. In implementation, use the manufacturer's recommended compensation and feedback arrangement, confirm the +4 minimum noise gain, and keep input and feedback traces short to prevent edge degradation.
おすすめ
Industrial Control and Sensor Signal Paths
OPA699ID can amplify and limit sensor signals in industrial systems where transient protection is needed close to the measurement front end. Its wide bandwidth supports fast sensor dynamics, and the integrated output limiter helps contain abnormal excursions before they reach a downstream converter or controller input. The approximately 1.5 mV offset and 3 µA bias current must be included in sensor-chain error calculations, particularly when the amplified signal is small. Use a noise gain of +4 or higher, provide local supply bypassing, and maintain a low-impedance return path so switching equipment and long sensor wiring do not degrade the measurement.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA699ID — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | OPA699IDG4 | OPA699IDRG4 | OPA699UID | OPA699UIDG4 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Amplifier Architecture | Voltage-feedback | Voltage-feedback | Voltage-feedback | Voltage-feedback | Voltage-feedback |
| Gain-Bandwidth Product | 1000 MHz | 1000 MHz | 1000 MHz | 1000 MHz | 1000 MHz |
| -3 dB Bandwidth | 260 MHz | 260 MHz | 260 MHz | 260 MHz | 260 MHz |
| Slew Rate | 1400 V/µs | 1400 V/µs | 1400 V/µs | 1400 V/µs | 1400 V/µs |
| Minimum Stable Gain | +4 V/V | +4 V/V | +4 V/V | +4 V/V | +4 V/V |
| Output Current | 120 mA | 120 mA | 120 mA | 120 mA | 120 mA |
| Output Limiting | Bipolar, approximately 1 V from each rail | Bipolar, approximately 1 V from each rail | Bipolar, approximately 1 V from each rail | Bipolar, approximately 1 V from each rail | Bipolar, approximately 1 V from each rail |
| Overdrive Recovery Time | 1 ns | 1 ns | 1 ns | 1 ns | 1 ns |
主な差別化要因
- Integrated high-speed bipolar output limiting (vs OPA828ID)
- Wideband signal-path performance (vs OPA699IDG4)
- Fast overload recovery for transient protection (vs OPA699IDRG4)
設計ノート
Do not configure the OPA699ID as a unity-gain voltage follower. The device is stable for noise gains of +4 V/V and above; using a lower gain can create ringing or instability. Establish the required noise gain in the feedback network, including any input attenuation, and confirm the resulting closed-loop bandwidth against the signal bandwidth. If the desired gain is below +4, use an additional gain stage or reconsider whether a unity-gain-stable amplifier is more appropriate.
Keep the feedback loop, input connection, and supply-bypass capacitor physically short to minimize parasitic inductance and capacitance. The OPA699ID has a 1 GHz gain-bandwidth product and 260 MHz -3 dB bandwidth, so PCB reactance can affect stability, bandwidth, and transient response. Use a continuous ground plane, short return paths, and decoupling placed directly at the supply pins. Avoid routing sensitive input and feedback nets beneath or parallel to fast switching-node traces.
Treat the internal limiter as a defined output boundary rather than a complete substitute for input-range protection. Its accuracy is approximately ±10 mV and its output can approach 1 V from each supply rail, but downstream circuitry must still tolerate that range. Check the ADC absolute maximum ratings, configure the OPA699ID at +4 noise gain or higher, and evaluate settling behavior with the complete source impedance, feedback network, and acquisition timing.
コンプライアンス情報
The OPA699ID is listed as an active Texas Instruments ordering option. Compliance attributes were not established from the manufacturer documentation excerpts, so they remain unknown rather than inferred.