S912XDP512J1CAGR - 16-bit S12X MCU, 512KB Flash, 80MHz, 144-LQFP | NXP
部品番号: S912XDP512J1CAGR ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.45 | $18.45 |
| 10 | $16.2 | $162.00 |
| 100 | $13.85 | $1,385.00 |
| 500 | $11.95 | $5,975.00 |
| 1,000 | $10.4 | $10,400.00 |
S912XDP512J1CAGR 概要
Background: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and a range of peripherals such as timers, ADCs, and communication controllers. The S12X family from NXP is a 16-bit CISC architecture derived from the original HC12, with the X-variant adding an enhanced XGate coprocessor and improved memory management for deterministic real-time control in automotive ECUs.
Key features include 4 KB of EEPROM for parameter storage, 8-channel 10-bit and 16-channel 10-bit ADC, PWM with up to 8 channels, plus low-voltage detect (LVD), power-on reset (POR), and a watchdog timer (WDT) for safety-critical operation. The S12X instruction set is source-compatible with the legacy HC12, easing migration of existing 16-bit code bases while doubling the typical throughput.
Typical applications span automotive body control modules (BCM), instrument clusters, HVAC controllers, lighting modules, industrial PLCs, and CAN/J1939 networked nodes. The dual-CAN interface and 119 GPIO count allow direct connection to multiple sensor and actuator networks without external bus expanders, reducing BOM cost.
When designing with this device, ensure the 5V supply is well decoupled with bulk and 100 nF ceramics near each VDD/VSS pair. Configure the PLL mode to 80 MHz only with a stable 4 MHz crystal; verify lock status in software before switching to PLL clock. For automotive EMC compliance, place the CAN transceivers close to the MCU and use a common-mode choke on the bus lines.
This page synthesizes distributor pricing from DigiKey/Mouser/Octopart, cross-references for drop-in alternatives within the S12X family, and practical design notes not collected in the manufacturer datasheet alone.
ドロップイン代替品: S912XDP512J1CAGR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: S912XDP512J1CAGR （同一形状・フットプリント） — 相違点: Core Architecture, Operating Temperature, Package.
クイック比較ツール — 並列比較する代替部品を選択:
S912XDP512J1CAL
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S912XDT512J1CAGR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S912XET512J2VAGR
✅ ドロップイン✓ 在庫あり
$1 / 個
データシートを見る →S912XEP768J5CAGR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S912XHZ512F1VAG
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S912XDP512J1CAGR 最大定格＆電気的特性
| Core Processor | HCS12X |
| Core Size | 16-Bit |
| Core Architecture | CISC (S12X) |
| Max Clock Speed | 80 MHz |
| Program Memory Size | 512 KB (512K x 8) Flash |
| Program Memory Type | FLASH |
| RAM Size | 32 KB |
| EEPROM Size | 4 KB |
| Number of I/O | 119 |
| パッケージ | 144-LQFP (20x20 mm) |
| 実装タイプ | Surface Mount |
| 電源電圧 | 2.5 V / 5 V |
| 動作温度 | -40C to +85C |
| AEC-Q100 Qualified | Yes |
| Communication Interfaces | CAN (2x), SCI, SPI, I2C |
| ADC | 8x10-bit + 16x10-bit |
| Peripherals | LVD, POR, PWM, WDT |
S912XDP512J1CAGR ピン構成
| ピン 1 | VDDR — Voltage regulator supply |
| ピン 2 | VDD1 — Core supply voltage |
| ピン 3 | VSS1 — Ground for core |
| ピン 4 | VDD2 — I/O supply voltage |
| ピン 5 | VSS2 — Ground for I/O |
| ピン 6 | XCLKS — Clock mode select |
| ピン 7 | EXTAL — External clock/crystal input |
| ピン 8 | XTAL — Crystal oscillator output |
| ピン 9 | RESET — External reset input (active low) |
| ピン 10 | TEST — Test mode input |
| ピン 11 | BKGD — Background Debug Mode (BDM) data |
| ピン 12 | MODC — Mode selection |
| ピン 13 | PAD0 — Port AD bit 0 (AN0) |
| ピン 14 | PAD1 — Port AD bit 1 (AN1) |
| ピン 15 | PAD2 — Port AD bit 2 (AN2) |
| ピン 16 | PAD3 — Port AD bit 3 (AN3) |
| ピン 17 | PAD4 — Port AD bit 4 (AN4) |
| ピン 18 | PAD5 — Port AD bit 5 (AN5) |
| ピン 19 | PAD6 — Port AD bit 6 (AN6) |
| ピン 20 | PAD7 — Port AD bit 7 (AN7) |
| ピン 21 | PAD8 — Port AD bit 8 (AN8) |
| ピン 22 | PAD9 — Port AD bit 9 (AN9) |
| ピン 23 | PAD10 — Port AD bit 10 (AN10) |
| ピン 24 | PAD11 — Port AD bit 11 (AN11) |
| ピン 25 | PAD12 — Port AD bit 12 (AN12) |
| ピン 26 | PAD13 — Port AD bit 13 (AN13) |
| ピン 27 | PAD14 — Port AD bit 14 (AN14) |
| ピン 28 | PAD15 — Port AD bit 15 (AN15) |
| ピン 29 | PA0 — Port A bit 0 |
| ピン 30 | PA1 — Port A bit 1 |
| ピン 31 | PA2 — Port A bit 2 |
| ピン 32 | PA3 — Port A bit 3 |
| ピン 33 | PA4 — Port A bit 4 |
| ピン 34 | PA5 — Port A bit 5 |
| ピン 35 | PA6 — Port A bit 6 |
| ピン 36 | PA7 — Port A bit 7 |
| ピン 37 | PB0 — Port B bit 0 |
| ピン 38 | PB1 — Port B bit 1 |
| ピン 39 | PB2 — Port B bit 2 |
| ピン 40 | PB3 — Port B bit 3 |
| ピン 41 | PB4 — Port B bit 4 |
| ピン 42 | PB5 — Port B bit 5 |
| ピン 43 | PB6 — Port B bit 6 |
| ピン 44 | PB7 — Port B bit 7 |
| ピン 45 | PE0 — Port E bit 0 (XRnDS, IRQ) |
| ピン 46 | PE1 — Port E bit 1 (IRQ) |
| ピン 47 | PE2 — Port E bit 2 |
| ピン 48 | PE3 — Port E bit 3 |
| ピン 49 | PE4 — Port E bit 4 |
| ピン 50 | PE5 — Port E bit 5 |
| ピン 51 | PE6 — Port E bit 6 |
| ピン 52 | PE7 — Port E bit 7 |
| ピン 53 | PH0 — Port H bit 0 (SPI0) |
| ピン 54 | PH1 — Port H bit 1 (SPI0) |
| ピン 55 | PH2 — Port H bit 2 (SPI0 SCK) |
| ピン 56 | PH3 — Port H bit 3 (SPI0 SS) |
| ピン 57 | PH4 — Port H bit 4 (SPI1) |
| ピン 58 | PH5 — Port H bit 5 (SPI1) |
| ピン 59 | PH6 — Port H bit 6 (SPI1 SCK) |
| ピン 60 | PH7 — Port H bit 7 (SPI1 SS) |
| ピン 61 | PJ0 — Port J bit 0 (CAN0 TX) |
| ピン 62 | PJ1 — Port J bit 1 (CAN0 RX) |
| ピン 63 | PJ2 — Port J bit 2 |
| ピン 64 | PJ3 — Port J bit 3 |
| ピン 65 | PJ4 — Port J bit 4 |
| ピン 66 | PJ5 — Port J bit 5 |
| ピン 67 | PJ6 — Port J bit 6 (CAN1 TX) |
| ピン 68 | PJ7 — Port J bit 7 (CAN1 RX) |
| ピン 69 | PK0 — Port K bit 0 |
| ピン 70 | PK1 — Port K bit 1 |
| ピン 71 | PK2 — Port K bit 2 |
| ピン 72 | PK3 — Port K bit 3 |
| ピン 73 | PK4 — Port K bit 4 |
| ピン 74 | PK5 — Port K bit 5 |
| ピン 75 | PK6 — Port K bit 6 |
| ピン 76 | PK7 — Port K bit 7 |
| ピン 77 | PM0 — Port M bit 0 |
| ピン 78 | PM1 — Port M bit 1 |
| ピン 79 | PM2 — Port M bit 2 |
| ピン 80 | PM3 — Port M bit 3 |
| ピン 81 | PM4 — Port M bit 4 |
| ピン 82 | PM5 — Port M bit 5 |
| ピン 83 | PM6 — Port M bit 6 |
| ピン 84 | PM7 — Port M bit 7 |
| ピン 85 | PP0 — Port P bit 0 (PWM0) |
| ピン 86 | PP1 — Port P bit 1 (PWM1) |
| ピン 87 | PP2 — Port P bit 2 (PWM2) |
| ピン 88 | PP3 — Port P bit 3 (PWM3) |
| ピン 89 | PP4 — Port P bit 4 (PWM4) |
| ピン 90 | PP5 — Port P bit 5 (PWM5) |
| ピン 91 | PP6 — Port P bit 6 (PWM6) |
| ピン 92 | PP7 — Port P bit 7 (PWM7) |
| ピン 93 | PS0 — Port S bit 0 (SCI0 TX) |
| ピン 94 | PS1 — Port S bit 1 (SCI0 RX) |
| ピン 95 | PS2 — Port S bit 2 (SCI1 TX) |
| ピン 96 | PS3 — Port S bit 3 (SCI1 RX) |
| ピン 97 | PS4 — Port S bit 4 |
| ピン 98 | PS5 — Port S bit 5 |
| ピン 99 | PS6 — Port S bit 6 |
| ピン 100 | PS7 — Port S bit 7 |
| ピン 101 | PT0 — Port T bit 0 (ECT channel 0) |
| ピン 102 | PT1 — Port T bit 1 (ECT channel 1) |
| ピン 103 | PT2 — Port T bit 2 (ECT channel 2) |
| ピン 104 | PT3 — Port T bit 3 (ECT channel 3) |
| ピン 105 | PT4 — Port T bit 4 (ECT channel 4) |
| ピン 106 | PT5 — Port T bit 5 (ECT channel 5) |
| ピン 107 | PT6 — Port T bit 6 (ECT channel 6) |
| ピン 108 | PT7 — Port T bit 7 (ECT channel 7) |
| ピン 109 | VDDPLL — PLL supply voltage |
| ピン 110 | VSSPLL — PLL ground |
| ピン 111 | VDDX1 — I/O supply segment 1 |
| ピン 112 | VSSX1 — I/O ground segment 1 |
| ピン 113 | VDDX2 — I/O supply segment 2 |
| ピン 114 | VSSX2 — I/O ground segment 2 |
| ピン 115 | VDDX3 — I/O supply segment 3 |
| ピン 116 | VSSX3 — I/O ground segment 3 |
| ピン 117 | VDDX4 — I/O supply segment 4 |
| ピン 118 | VSSX4 — I/O ground segment 4 |
| ピン 119 | VDDX5 — I/O supply segment 5 |
| ピン 120 | VSSX5 — I/O ground segment 5 |
| ピン 121 | VDDX6 — I/O supply segment 6 |
| ピン 122 | VSSX6 — I/O ground segment 6 |
| ピン 123 | VDDX7 — I/O supply segment 7 |
| ピン 124 | VSSX7 — I/O ground segment 7 |
| ピン 125 | VDDA — ADC supply voltage |
| ピン 126 | VSSA — ADC ground |
| ピン 127 | VRH — ADC high reference voltage |
| ピン 128 | VRL — ADC low reference voltage |
| ピン 129 | PU0 — Port U bit 0 |
| ピン 130 | PU1 — Port U bit 1 |
| ピン 131 | PU2 — Port U bit 2 |
| ピン 132 | PU3 — Port U bit 3 |
| ピン 133 | PU4 — Port U bit 4 |
| ピン 134 | PU5 — Port U bit 5 |
| ピン 135 | PU6 — Port U bit 6 |
| ピン 136 | PU7 — Port U bit 7 |
| ピン 137 | PV0 — Port V bit 0 |
| ピン 138 | PV1 — Port V bit 1 |
| ピン 139 | PV2 — Port V bit 2 |
| ピン 140 | PV3 — Port V bit 3 |
| ピン 141 | PV4 — Port V bit 4 |
| ピン 142 | PV5 — Port V bit 5 |
| ピン 143 | PV6 — Port V bit 6 |
| ピン 144 | PV7 — Port V bit 7 |
主な用途
S912XDP512J1CAGR の用途: 7 件s: Automotive Body Control Module, Industrial CAN/J1939 Networked Node, Automotive Instrument Cluster, HVAC Climate Control Module, Lighting Control Module (LED Matrix), Automotive Gateway/Bus Bridge, Industrial PLC/Automation Controller.
Automotive Body Control Module
The S912XDP512J1CAGR's 512 KB Flash, 32 KB RAM, 119 GPIO, and dual CAN interfaces directly fit body control modules that orchestrate lighting, door locks, wipers, and mirrors in modern vehicles. With two msCAN 2.0A/B controllers the MCU can bridge body-CAN with chassis-CAN without external logic, while 119 GPIO drive multiple LED matrix and relay channels directly. The AEC-Q100 Grade-1 qualification and -40C to +85C operating range meet cabin and under-hood thermal budgets. Place the MCU between the 5V LDO and the load drivers, using opto-isolation on the CAN bus lines for EMC immunity. Designers benefit from the S12X core's deterministic interrupt response and the legacy HC12 source compatibility for porting existing BCM firmware. Compared to newer Cortex-M parts, the S12X offers proven automotive longevity and a mature toolchain.
おすすめ
Industrial CAN/J1939 Networked Node
The S912XDP512J1CAGR suits industrial J1939 nodes thanks to its dual CAN 2.0A/B controllers, 80 MHz S12X core, and AEC-Q100 reliability for harsh environments. With 512 KB Flash, the MCU holds the full SAE J1939 protocol stack alongside application logic, while 32 KB RAM buffers incoming CAN frames during peak bus load. The 119 GPIO pins interface directly with 24V industrial sensors and actuators via external drivers. Mount the MCU on a 4-layer PCB with proper ground stitching for EMI immunity, and add common-mode chokes on the CAN bus for Class A industrial EMC compliance. The S12X CISC core's deterministic interrupt latency outperforms Cortex-M0 parts when handling high-priority CAN error frames. Compared to the S912XHZ512F1VAG, this DP512 variant is better suited for general node duties rather than motor-control applications.
おすすめ
Automotive Instrument Cluster
The S912XDP512J1CAGR drives automotive instrument clusters by combining 512 KB Flash for gauge graphics and CAN connectivity with 32 KB RAM for frame buffer management. Its dual CAN controllers receive vehicle speed, RPM, fuel level, and warning signals directly from the chassis CAN bus without an external coprocessor. The 119 GPIO drive stepper-motor gauges, warning LEDs, and LCD segments while the integrated PWM channels dim backlights. AEC-Q100 Grade-1 qualification and -40C to +85C operation cover cabin thermal environments. Designers should isolate the analog gauge drive traces from the CAN bus lines to minimize crosstalk on the PCB. Compared to 32-bit Cortex-M alternatives, the S12X core offers simpler deterministic execution for cluster timing budgets. The XGate coprocessor offloads CAN message parsing to free the main CPU for gauge sweep animations.
おすすめ
HVAC Climate Control Module
The S912XDP512J1CAGR powers automotive HVAC climate modules by leveraging its 119 GPIO to drive blower-motor PWM signals, temperature-sensor ADCs, and flap-actuator H-bridges. With 512 KB Flash, the MCU stores complete climate-control algorithms including PID loops and CAN-based setpoint reception from the body controller. The dual CAN interfaces connect to both the body CAN network and the powertrain CAN for engine-load compensation of A/C compressor requests. AEC-Q100 Grade-1 reliability and -40C to +85C operation handle under-dash thermal environments. Use the 8+16 channel 10-bit ADCs to read cabin and ambient NTC sensors simultaneously, simplifying the analog front end. Compared to discrete analog controllers, this MCU integrates the full climate-control logic into a single AEC-Q100 chip, reducing BOM count by 30-40%.
おすすめ
Lighting Control Module (LED Matrix)
The S912XDP512J1CAGR orchestrates automotive LED matrix headlamp and taillight modules using its 119 GPIO and 8-channel PWM peripherals. With 512 KB Flash it stores matrix-beam pixel control algorithms, while the dual CAN interfaces receive camera-based high-beam requests and adaptive-driving-beam commands. The S12X core's deterministic interrupt handling ensures sub-millisecond PWM updates to prevent LED flicker visible on camera systems. AEC-Q100 Grade-1 qualification and -40C to +85C operation suit under-hood and headlamp housing environments. Drive the LED strings via external MOSFETs controlled by the PWM outputs, isolating the MCU ground from high-current LED switching returns. Compared to a Cortex-M0 design, the S12X's larger Flash accommodates more complex matrix algorithms without external memory.
おすすめ
Automotive Gateway/Bus Bridge
The S912XDP512J1CAGR functions as a CAN gateway or bus bridge using its dual independent msCAN 2.0A/B controllers to forward messages between two automotive networks at different baud rates. The 512 KB Flash stores gateway routing tables and message-filter algorithms, while the 32 KB RAM buffers full CAN frames during high-load bridging. The S12X core's deterministic interrupt latency prevents message loss during simultaneous bus peaks. AEC-Q100 Grade-1 and -40C to +85C operation allow deployment in central-body or under-dash gateway housings. Implement message filtering in software using the msCAN acceptance masks to offload bus traffic before forwarding. Compared to dedicated bridge ICs, this MCU offers flexibility to update routing firmware over CAN, eliminating factory reprogramming.
おすすめ
Industrial PLC/Automation Controller
The S912XDP512J1CAGR serves as a compact industrial PLC or automation controller thanks to its 512 KB Flash for ladder-logic translation and 119 GPIO for direct sensor/actuator interfacing. The dual CAN ports enable CANopen or DeviceNet communication alongside RS-485 over the SCI ports, covering most industrial networking protocols. The S12X core's deterministic execution suits hard-real-time scan loops under 10 ms typical for small-PLC applications. AEC-Q100 Grade-1 qualification and -40C to +85C operation handle factory-floor thermal environments. Use opto-isolators on all GPIO channels driving 24V industrial loads, and add TVS diodes on the CAN bus for surge protection. Compared to dedicated PLC CPUs, this MCU offers a more flexible C-programmable platform with the same GPIO density.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: S912XDP512J1CAGR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | S912XDP512J1CAL | S912XDT512J1CAGR | S912XET512J2VAGR | S912XEP768J5CAGR | S912XHZ512F1VAG |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 144-LQFP (20x20 mm) | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same |
| Core Architecture | HCS12X 16-bit CISC | HCS12X 16-bit CISC | HCS12X 16-bit CISC | HCS12X 16-bit CISC | HCS12X 16-bit CISC | HCS12X 16-bit CISC |
| Clock Speed | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 768 KB (+50%) | 512 KB |
| RAM | 32 KB | 32 KB | 32 KB | 32 KB | 48 KB | 32 KB |
| GPIO Count | 119 | 119 | 119 | 119 | 119 | 119 |
| CAN Interfaces | 2 (msCAN 2.0A/B) | 2 | 2 | 2 | 3 | 2 |
| Temperature Grade | -40C to +85C (Grade-1) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (Grade-0) |
| AEC-Q100 | Yes | Yes | Yes | Yes | Yes | Yes |
主な差別化要因
- Larger Flash with full S12X feature set in same footprint （vs S912XHZ512F1VAG)
- Same Flash as MC9S12XDT512J1CAGR but enhanced XGate coprocessor （vs S912XDT512J1CAGR)
- Established automotive track record over newer XEP768 （vs S912XEP768J5CAGR)
設計ノート
Provide a clean 5V supply to all VDDX pins and a separate filtered 2.5V analog supply to VDDA/VRH/VRL. Place 100 nF ceramic decoupling capacitors on every VDD/VSS pin pair within 5 mm of the package body, and add a 10 uF bulk tantalum or ceramic cap on the main 5V rail. The on-chip voltage regulator requires a low-ESR bulk cap on VDDR (typically 4.7 uF or larger) to maintain stability under peak load transients. Decouple the PLL supply pins VDDPLL/VSSPLL with a dedicated 100 nF + 10 nF cap pair to minimize jitter on the 80 MHz system clock.
Route the EXTAL/XTAL traces as a guarded differential pair directly under the chip with a continuous ground plane beneath them. Keep crystal traces under 10 mm total length and place load capacitors within 2 mm of the EXTAL/XTAL pins. Avoid routing high-current switching signals (PWM, relay drive) parallel to the crystal traces to prevent clock jitter. Use a 4-layer PCB with dedicated ground and power planes for automotive EMC compliance.
Always program the PLL configuration registers BEFORE switching the clock source from the PLL to the bus clock; otherwise the MCU can lock up if the PLL loses lock. Verify PLL lock status by polling the LOCK bit in the CRG PLL register. Never exceed the maximum 5.5V on any VDD pin - automotive load-dump events can produce transients above 40V, so add a TVS diode (e.g., SMBJ5.0A) on the main supply rail. The BDM (BKGD) pin must be left high-impedance in normal operation or pulled high through a 10k resistor; never drive it actively without proper sequencing.
For CAN bus signaling, keep the CANH/CANL traces as a 100-ohm-impedance differential pair with matched length (±5 mm tolerance) and place a 120-ohm termination resistor at each end of the bus segment. Add a split-termination capacitor network (typically 4.7 nF + 100 nF) at each node to improve EMC performance. Avoid routing CAN traces near noisy switching nodes like relay coils or motor drive H-bridges; if unavoidable, place a ground guard trace between them.
コンプライアンス情報
AEC-Q100 Grade-1 qualified per NXP product page. RoHS and REACH compliant. Halogen-free per JEDEC JS709B. Conflict-mineral compliant per NXP supplier declarations.
