S9S12H128J2VFVE - 16-bit S12 MCU 128KB Flash 50MHz | NXP
部品番号: S9S12H128J2VFVE ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $14.85 | $14.85 |
| 10 | $13.2 | $132.00 |
| 100 | $11.55 | $1,155.00 |
| 500 | $9.95 | $4,975.00 |
| 1,000 | $8.6 | $8,600.00 |
S9S12H128J2VFVE 概要
A microcontroller (MCU) is a single-chip computer containing a CPU, program and data memory, and a set of on-chip peripherals. The HCS12 core is an enhanced evolution of the HC11 architecture with a 16-bit data path, a richer instruction set, and higher code efficiency for embedded control. Within the broader semiconductor taxonomy, this part sits as a microcontroller -> embedded processor -> semiconductor device.
Key features include 128KB Flash for application code and a 50MHz CPU core, full CAN and LIN connectivity for in-vehicle networking, an enhanced capture/timer and PWM module (ECT) for motor and actuator control, and a 10-bit analog-to-digital converter for sensor acquisition. The 144-LQFP footprint exposes a wide peripheral set: SCI/SPI, I2C, multiple timer channels, and a robust interrupt controller.
The S12H silicon was designed for cost-sensitive automotive body controllers, HVAC panels, instrument clusters, and DC motor control nodes. Its peripheral-rich architecture lets designers replace external logic with on-chip modules, reducing BOM count while keeping deterministic interrupt latency for safety-critical loops.
Typical applications include automotive body control modules (BCM), HVAC door and blower control, instrument cluster slaves, and LIN/CAN-based sensor nodes. The wide temperature range and on-chip CAN make it equally attractive for industrial PLC I/O expanders and remote sensor hubs.
When designing with this part, pay attention to the 5V supply rail tolerance and provide adequate decoupling near the multiple VDD pins. Use NXP's CodeWarrior or the GCC S12 toolchain with a BDM interface for in-circuit debug, and consult the S12H reference manual for peripheral allocation to avoid conflicts on shared pins.
This page synthesizes distributor pricing, NXP/Freescale part-family alternatives, and practical design notes not found in a single source, giving an engineer a one-stop reference for the S9S12H128J2VFVE.
ドロップイン代替品: S9S12H128J2VFVE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: S9S12H128J2VFVE （同一形状・フットプリント） — 相違点: Package, Operating Temperature, Supply Voltage, Mounting Type, ADC.
クイック比較ツール — 並列比較する代替部品を選択:
MC9S12H256VFVE
✅ ドロップイン✓ 在庫あり
$10.95 / 個
データシートを見る →MC9S12H256VFVER
✅ ドロップイン✓ 在庫あり
$10.95 / 個
データシートを見る →S912XEQ512J2MAA
✅ ドロップイン✓ 在庫あり
$8.6 / 個
データシートを見る →S912XEQ512J2MAL
✅ ドロップイン✓ 在庫あり
$17.95 / 個
データシートを見る →S912XEG384J2CALR
✅ ドロップイン✓ 在庫あり
$9.1 / 個
データシートを見る →S9S12H128J2VFVE 最大定格＆電気的特性
| Core | HCS12 (S12) |
| データバス幅 | 16-bit |
| Program Memory Size | 128 KB Flash |
| Maximum CPU Clock | 50 MHz |
| 電源電圧 | 5 V (typical); 4.5 V to 5.5 V (range) |
| 動作温度 | -40C to +105C |
| パッケージ | 144-LQFP (20x20 mm), 0.5 mm pitch |
| 実装タイプ | Surface Mount, Gull-Wing leads |
| Automotive Qualification | Yes |
| Connectivity | CAN, LIN, SCI (UART), SPI, I2C |
| ADC | 10-bit (resolution) |
| Timers/PWM | Enhanced Capture Timer (ECT), PWM module |
| RoHS ステータス | Compliant |
| Lead-Free / Halogen-Free | Compliant (lead-free, Pb-free terminal finish) |
| MSLレベル | 3 (per JEDEC J-STD-020) |
S9S12H128J2VFVE 144-lqfp (20x20 mm), 0.5 mm pitch ピン配置ガイド
S9S12H128J2VFVE (144-lqfp (20x20 mm), 0.5 mm pitch パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: S9S12H128J2VFVE.
詳細は データシート をご参照ください。
主な用途
S9S12H128J2VFVE の用途: 8 件s: Automotive Body Control Modules (BCM), HVAC Door and Blower Controllers, Instrument Cluster Slaves, LIN/CAN Sensor and Actuator Nodes, Industrial PLC I/O Expanders, DC Motor and Relay Driver Control Nodes, Consumer and Appliance Control Boards, Automotive Lighting and Wiper ECUs.
Automotive Body Control Modules (BCM)
The S9S12H128J2VFVE fits automotive body control modules because it combines a deterministic 16-bit HCS12 core at 50 MHz with on-chip CAN and LIN interfaces, 128 KB Flash, and -40C to +105C qualification. Placed as the master MCU of a BCM, it aggregates signals from door, lighting, and wiper subsystems over LIN while streaming status onto the vehicle's high-speed CAN backbone. Compared with a switching regulator front end, its 5 V supply tolerance simplifies 12 V battery rail powering with a single linear post-regulator. The 144-LQFP package exposes enough GPIO and PWM channels for direct-drive of relays, FET pre-drivers, and LED matrix backlights without external expanders.
おすすめ
HVAC Door and Blower Controllers
The S9S12H128J2VFVE is well matched to HVAC door and blower controllers thanks to its Enhanced Capture Timer (ECT) and PWM modules, which drive DC motors and stepper actuators for blend/door/mode control. The HCS12 core at 50 MHz executes PID loops for closed-loop blower speed regulation within tight interrupt latency windows. On-chip 10-bit ADC reads mixed-air temperature sensors and potentiometer feedback, while on-chip SCI/UART links to the climate control master. The 144-LQFP footprint exposes the timer channel count needed to run multiple motors and a PWM-driven BLDC blower simultaneously.
おすすめ
Instrument Cluster Slaves
In instrument clusters the S9S12H128J2VFVE serves as a slave or co-processor that drives stepper gauges, indicator LEDs, and warning lamps while communicating with a master HMI processor over SPI or CAN. The HCS12 core handles backlight dimming via PWM and CAN-readable diagnostic data without taxing the host MCU. Its 128 KB Flash holds gauge calibration tables and telltale logic; 6 KB RAM buffers transient driving-cycle data for boot-up gauge sweep routines. The -40C to +105C rating covers harsh under-dash thermal environments.
おすすめ
LIN/CAN Sensor and Actuator Nodes
Distributed sensor ECUs such as those for seat position, sunroof tilt, and mirror-fold use the S9S12H128J2VFVE to read 10-bit ADC channels and drive small brushed motors over LIN. Its on-chip LIN 2.x interface plus msCAN lets it talk to multiple bus types in one package, simplifying wiring harnesses. The 50 MHz HCS12 core easily services the input sampling and LIN schedule slots while leaving headroom for diagnostics. The 144-LQFP footprint and wide 5 V supply tolerance match automotive sensor electronics exposed under seats and doors.
おすすめ
Industrial PLC I/O Expanders
In industrial PLCs and remote I/O blocks, the S9S12H128J2VFVE serves as a deterministic 16-bit local controller that aggregates digital inputs, drives solid-state relays, and reports state to a master PLC over CANopen or DeviceNet. The enhanced capture timer precisely timestamps events for sequencing; the 10-bit ADC handles analog sensor reads of 4-20 mA or 0-10 V inputs. The wide -40C to +105C rating extends operation to non-climate-controlled cabinets. Compared with ARM-based MCUs, the HCS12 offers predictable interrupt latency for sub-millisecond scan loops in factory automation.
おすすめ
DC Motor and Relay Driver Control Nodes
The S9S12H128J2VFVE is a natural fit for compact DC motor controllers used in power-window regulators, seat adjusters, and wiper mechanisms, where its PWM and ECT modules drive H-bridges through FET pre-drivers. The HCS12 core runs current-limit and stall-detection algorithms in real time, protecting the actuator against overcurrent conditions. The 144-LQFP package exposes enough GPIO to monitor end-of-travel switches and emit diagnostic pulses back over LIN. The 5 V supply operates directly from a regulated 12 V battery rail, simplifying BOM.
おすすめ
Consumer and Appliance Control Boards
Beyond automotive, the S9S12H128J2VFVE serves as the main controller in higher-end white goods and HVAC appliances where deterministic motor control, multiple communication ports, and reliability matter. The HCS12 core drives inverter-driven compressors and pumps; CAN/LIN ports connect to indoor/outdoor unit boards; the 10-bit ADC handles temperature and pressure sensing. Its 144-LQFP package suits large home-appliance mainboards with abundant I/O, and the industrial temperature grade supports garage and basement installations.
おすすめ
Automotive Lighting and Wiper ECUs
Front-lighting modules and adaptive wiper ECUs use the S9S12H128J2VFVE to drive LED strings and brushless wiper motors via ECT/PWM outputs while coordinating across CAN with the BCM. The 16-bit HCS12 handles complex matrix-beam algorithms including thermal foldback and oncoming-light detection offloading. The 10-bit ADC channels read photocells and steering-angle sensors, while SPI connects to LED matrix drivers. Compared with discrete logic, the integrated MCU reduces PCB area and improves EMC immunity in the headlights enclosure.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: S9S12H128J2VFVE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S12H256VFVE | MC9S12H256VFVER | S912XEQ512J2MAA | S912XEQ512J2MAL | S912XEG384J2CALR |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 144-LQFP (20x20 mm) | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same |
| Core | HCS12 (S12) | HCS12 (S12) | HCS12 (S12) | S12X (with XGATE coprocessor) | S12X (with XGATE coprocessor) | S12X (with XGATE coprocessor) |
| Program Memory | 128 KB Flash | 256 KB Flash (+100%) | 256 KB Flash (+100%) | 512 KB Flash (+300%) | 512 KB Flash (+300%) | 384 KB Flash (+200%) |
| Maximum CPU Clock | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Supply Voltage | 5 V (4.5 V to 5.5 V) | 5 V (4.5 V to 5.5 V) | 5 V (4.5 V to 5.5 V) | 5 V | 5 V | 5 V |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C (variant dependent) | -40C to +85C | -40C to +85C |
| CAN/LIN Connectivity | msCAN + LIN 2.x | msCAN + LIN | msCAN + LIN | msCAN + LIN + flexRAY (in X family) | msCAN + LIN | msCAN + LIN |
| ADC | 10-bit | 10-bit | 10-bit | 10-bit / 12-bit | 10-bit / 12-bit | 10-bit / 12-bit |
| RoHS Compliant | Yes | Yes | Yes | Yes | Yes | Yes |
主な差別化要因
- HCS12 core optimized for real-time event-driven automotive control （vs S912XEQ512J2MAA)
- Lower Flash density for cost-sensitive nodes - drop-in upgradable （vs MC9S12H256VFVE)
- Wide 5 V supply tolerance ideal for automotive battery-rail designs （vs S912XEQ512J2MAL)
- Established NXP/Freescale S12H family with mature automotive toolchain （vs Newer S32K family)
設計ノート
Decouple every VDD/VSS pin pair with a 100 nF X7R ceramic placed within 5 mm of the package, plus a single bulk 4.7 uF tantalum or aluminum-polymer near the supply pin pair. The 5 V rail tolerance (4.5 V to 5.5 V) accommodates cranking transients; however, add a series ferrite or small L-C filter for 12 V battery reverse-polarity protection. S12H core draws tens of mA; the bulk capacitor must hold VDD within tolerance during BDM debug events that momentarily increase current. Estimated: at 50 MHz core clock with all peripherals active, total IDD is approximately 50 mA typical - confirm against the NXP S12H128 data sheet for final BOM sizing.
The 144-LQFP at 0.5 mm pitch needs careful escape routing: use 0.2 mm traces/space and via-in-pad only if the PCB fabricator supports it; otherwise fan out to micro-vias on inner layers. Keep BDM clock and BDM data traces short (<50 mm) and shielded by GND on both sides to avoid glitches during in-circuit programming. Place the external oscillator or resonator within 8 mm of the EXTAL/XTAL pins, with a guarded ground ring. Provide a single GND reference plane under the package and avoid splitting it; the S12H's bond-wire ground is sensitive to return-path discontinuity that can increase EMI.
Do NOT connect unused I/O pins directly to VDD - the S12H lacks internal pull-ups on all ports and floating inputs may source extra current or reset unpredictably. Tie them individually to GND through 10 kohm resistors or configure as outputs. When migrating firmware from a S12T or S12C part, verify peripheral base addresses - they differ across S12 sub-families. The S12H core does NOT support the same D-Flash EEPROM emulation library as the S12XE; reuse code only after testing. Estimated: programming/erase endurance is approximately 10K cycles - wear-level the EEPROM emulation buffer.
The CAN bus TXD output is push-pull CMOS and needs an external CAN transceiver such as TJA1050T or TJA1043 - do not connect the S12H CAN pins directly to a bus. For LIN, add the external transceiver and the typical pull-up resistor on the LIN bus. SPI signals routed to external drivers should be length-matched within 5 mm if running above 5 MHz to avoid skew-induced errors. Place a 33 pF RC filter near the input of any high-impedance analog signal to attenuate RF interference, and keep digital return currents away from the ADC channels on Port AD.
Keep the BDM connector away from switching power inductors and H-bridges to avoid programming failures. Provide a 4.7 kohm pull-up on the BKGD line to ensure reliable background debug mode entry, even when the target is held in reset. Reserve a small prototype area with test points for TX/RX, RESET, and VDD - these are essential for any future in-field firmware debug. Estimated: a 4-layer 1 oz copper stackup with 0.36 mm finished vias supports the 0.5 mm pitch fan-out cleanly; thinner traces may require laser micro-vias.
コンプライアンス情報
RoHS-compliant and Pb-free terminal finish per NXP/Freescale product pages. AEC-Q100 automotive qualified per NXP/Freescale qualification reports. Reach SVHC compliance maintained. Conflict minerals declaration on file with NXP.
