SN74LS629N - Dual 20 MHz VCO | Texas Instruments
部品番号: SN74LS629N ✓ 生産中SN74LS629N 概要
A voltage-controlled oscillator, or VCO, is a timing and frequency-generation circuit whose output frequency is controlled by an externally applied voltage. It belongs to the oscillator and clock-and-timing IC hierarchy, where it combines a stable internal oscillator with a voltage-to-frequency conversion function. The dual architecture provides two oscillator channels in one package, reducing component count and board area when a system requires two related but independently adjustable timing signals.
The primary electrical characteristics of the SN74LS629N include two voltage-controlled oscillator sections, a maximum frequency of 20 MHz, and a 16-pin PDIP package rated for a 0°C to 70°C operating temperature range. The N package suffix identifies the standard through-hole PDIP configuration. The device is associated with the SN74LS629 family, which is categorized by Texas Instruments as a programmable timer and oscillator product within the 74LS logic family.
The dual VCO structure makes the SN74LS629N useful when two frequencies must vary without using two separate oscillator packages. Each oscillator can be driven by its own control voltage, allowing one channel to act as a reference while the other performs modulation or sweep generation. Designers should account for the control-voltage range, transfer gain, output drive, and load capacitance listed in the manufacturer datasheet when setting the operating point.
Typical uses include low- and intermediate-frequency signal generation, voltage-controlled frequency references, sweep and ramp generation, two-channel modulation systems, tone-shaping circuits, and instrumentation. In laboratory equipment, the two sections can generate a carrier and a variable clock. In communications equipment, they can support adjustable local timing or modulation. In industrial controls, they can provide a programmable frequency reference where a fixed crystal oscillator is insufficient.
The principal design consideration is signal integrity around the control inputs. Keep control-voltage traces short, isolate them from fast switching nodes, and use a clean reference voltage to prevent frequency jitter. The 20 MHz upper frequency is a maximum device capability rather than a guarantee of useful output quality at every control voltage, load, supply, or temperature. Confirm timing margins and output-waveform requirements in the target system before release.
This page organizes the manufacturer product information, exact-orderable package details, sourcing guidance, and engineering selection notes for the SN74LS629N. It also identifies why true drop-in replacements are uncommon: equivalent oscillator functions generally use a different package, pinout, supply family, or control characteristic, making an unverified substitution risky.
ドロップイン代替品: SN74LS629N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストSN74LS629N 仕様
| Product Type | Dual voltage-controlled oscillator |
| Number of Oscillator Sections | 2 sections |
| Maximum Frequency | 20 MHz |
| Frequency Control Method | External control voltage |
| 動作温度範囲 | 0°C to 70°C |
| Package Type | PDIP-16, N package |
| ピン数 | 16 pins |
| 実装スタイル | Through-hole |
| Logic Family | 74LS |
| 動作温度 | 0°C to 70°C |
SN74LS629N pdip-16, n package ピン配置ガイド
SN74LS629N (pdip-16, n package パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: SN74LS629N.
詳細は データシート をご参照ください。
主な用途
SN74LS629N の用途: 6 件s: Dual-Channel Tone Generator, Frequency-Sweep Instrumentation, Voltage-Controlled Clock Reference, FM and AM Signal Modulation, Industrial Timing and Control, Laboratory Test and Measurement.
Dual-Channel Tone Generator
The SN74LS629N fits dual-channel tone-generation systems because its two voltage-controlled oscillator sections can be adjusted with separate control voltages. A control block can sweep or modulate one channel while the other supplies a stable reference tone, allowing the design to compare two related frequencies. With a maximum oscillator frequency of 20 MHz, the device covers low- and intermediate-frequency audio and instrumentation ranges rather than microwave signal generation. The implementation should use low-noise control references and keep sensitive timing traces away from digital switching nodes. Output loading and permissible waveform characteristics must follow the manufacturer datasheet because the 20 MHz value is a maximum device rating, not a guarantee of equal performance at every control voltage.
おすすめ
Frequency-Sweep Instrumentation
The SN74LS629N is suitable for a voltage-programmed sweep source because either oscillator section can vary in frequency as its control voltage changes. A ramp generator and digital-to-analog conversion path can command the oscillator, while a counter can capture or display the resulting frequency. Its dual-channel architecture allows a second section to generate a reference or marker signal. The device supports operation up to 20 MHz, but useful sweep accuracy also depends on control-voltage resolution, oscillator transfer characteristics, and counter resolution. Engineers should evaluate settling behavior and temperature drift over the intended sweep range rather than assuming constant tuning sensitivity across the full frequency span.
おすすめ
Voltage-Controlled Clock Reference
A clock-reference design can use one SN74LS629N section as a continuously adjustable timing source and reserve the other section for a related auxiliary clock. This arrangement is useful in calibration equipment, adjustable dividers, and test systems where a fixed oscillator cannot provide the required tuning range. The 16-pin PDIP package supports through-hole prototyping and inspection, while the 0°C to 70°C N-package specification covers commercial ambient conditions. Timing-critical downstream circuits should be evaluated for jitter and duty-cycle distortion, because a maximum frequency rating alone does not characterize edge quality. Stable reference generation and careful grounding are essential when the oscillator output drives digital counters or precision timing circuits.
おすすめ
FM and AM Signal Modulation
The SN74LS629N can serve as a carrier oscillator in a basic voltage-controlled modulation circuit, with the external control input receiving the modulating waveform. The second oscillator section can generate a second carrier, reference tone, or auxiliary modulation source. Because the device is specified up to 20 MHz, it is best suited to low- and intermediate-frequency transmitters rather than RF carrier generation. Distortion and modulation fidelity depend on the oscillator's voltage-to-frequency linearity and the bandwidth of the control path. Keep modulation transients away from supply and logic pins, provide adequate input decoupling, and verify output swing into the following stage before establishing the modulation index.
おすすめ
Industrial Timing and Control
The SN74LS629N can provide adjustable timing signals in an industrial controller when the mechanism requires frequency variation rather than a fixed clock. One channel may drive a pulse-rate actuator while the other produces a supervisory or phase-related signal. Its dual sections reduce the number of separate oscillator packages, and the PDIP format is convenient for rugged through-hole control boards during prototyping. The commercial 0°C to 70°C rating must be checked against the enclosure temperature and nearby heat sources. Because an industrial environment can introduce supply and control-voltage noise, use filtering, grounding, and shielding that do not distort the required tuning bandwidth. Confirm restart behavior and output timing before using the oscillator as a safety-critical reference.
おすすめ
Laboratory Test and Measurement
The SN74LS629N is useful in a laboratory oscillator or function-generator accessory where a voltage variable output is needed. One oscillator section can generate the test waveform while the second creates a reference or auxiliary output for triggering and comparison. The maximum 20 MHz frequency supports many low-frequency waveform, clock, and response tests. The through-hole PDIP package is particularly convenient for educational and prototype boards where socketed construction and easy inspection are valuable. Measurement accuracy still depends on the external control DAC, supply regulation, grounding, and output loading. Use calibrated instrumentation to characterize frequency versus control voltage and ensure the selected control range remains within the oscillator's specified operating limits.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN74LS629N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Brand | Texas Instruments |
| Package | 16-pin PDIP |
| Oscillator Sections | 2 |
| Maximum Frequency | 20 MHz |
| Frequency Control | External control voltage |
| Operating Temperature | 0°C to 70°C |
| Mounting Style | Through-hole |
| Logic Family | 74LS |
主な差別化要因
- Two oscillator sections are integrated in one package (vs TS974IDT)
- Frequency can be controlled by an external voltage (vs GAL16V8B-25LP)
- Exact-orderable through-hole package for legacy-style PCB layouts (vs SN74LS629DR)
設計ノート
Route each oscillator control-voltage trace directly to its intended pin and keep it away from the other oscillator output and digital logic. Use a continuous ground reference beneath the control path where practical. Because the SN74LS629N supports operation up to 20 MHz, long control traces can behave like antennas and convert switching noise into frequency modulation. Keep external filtering components close to the control source and confirm that added capacitance does not degrade the required tuning bandwidth.
Provide the device with its specified supply voltage and place local bypass capacitance at the power pins. The exact capacitor value and acceptable ripple conditions should be taken from the manufacturer datasheet rather than inferred from the logic family. Stable supply and ground connections are particularly important for an oscillator because supply variation can appear as output-frequency variation. Keep power-supply return currents from sharing the sensitive control-reference return path to minimize common-impedance disturbance.
Do not treat the 20 MHz maximum frequency as a guaranteed operating point across every supply voltage, control voltage, temperature, and output load. Characterize tuning range, output amplitude, duty-cycle distortion, and frequency stability in the intended circuit. Also verify whether the second oscillator section can be used independently; shared supply and ground pins do not guarantee identical control behavior or timing relationships.
Avoid ordering SN74LS629DR or SN74LS629NSRG4 as substitutes for SN74LS629N without redesigning the PCB. Those identified variants use surface-mount packages rather than the exact 16-pin PDIP footprint. A replacement is a true drop-in option only when package dimensions, lead geometry, terminal numbering, control range, supply requirements, and timing characteristics all align with the original design.
コンプライアンス情報
Compliance declarations are not stated on the exact-orderable product listing excerpt. Confirm current RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation with Texas Instruments before release.