TLV320AIC3106IRGZT - Low-Power Stereo Audio CODEC | TI
部品番号: TLV320AIC3106IRGZT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.95 | $8.95 |
| 10 | $7.96 | $79.60 |
| 100 | $7.05 | $705.00 |
| 500 | $5.9 | $2,950.00 |
| 1,000 | $5.05 | $5,050.00 |
| 2,500 | $4.4 | $11,000.00 |
TLV320AIC3106IRGZT 概要
An audio CODEC (coder-decoder) is an integrated circuit that converts between digital audio streams and analog microphone/line/headphone signals, combining an ADC input path and DAC output path inside a single chip. The TLV320AIC3106 sits in the broader hierarchy of audio interface ICs -> interface ICs -> integrated circuits, and is widely deployed in portable, battery-powered, and space-constrained designs where low power, stereo playback, and integrated headphone drive are required simultaneously. Multiple line, microphone, and headphone amplifiers share an extensive register-based power-control interface, enabling fine-grained energy management as system use cases change.
Key features of the TLV320AIC3106 include stereo 24-bit ADC and DAC with 102 dBA SNR, integrated 40 mW headphone amplifier, programmable 3D / bass / treble / EQ digital effects, and selectable single-ended or fully-differential analog inputs. The digital serial audio bus supports I2S, left-justified, right-justified, and DSP/PCM modes for flexible connection to virtually any application processor or DSP. An automatic gain control (AGC) block on the ADC path keeps microphone levels stable across varying speech distances.
At the architectural level the device pairs a multi-bit delta-sigma modulator front end with on-chip FIR and IIR engine blocks so that tone control, EQ, and de-emphasis are applied digitally without burdening the host processor. PLL-based clock generation accepts common 12, 13, 24, or 27 MHz system clocks and derives all internal timing from them, simplifying board layout by removing the need for a dedicated audio master crystal in many designs. Extensive register-based power control keeps unused analog blocks powered down until audio paths are activated.
Typical applications span portable media players, portable navigation devices, mobile phones and VoIP handsets, portable gaming, digital still cameras and camcorders, ultrasonic imaging, IP phones and USB headsets, as well as portable audio docks and Bluetooth speakers. The combination of low power, integrated headphone drive, and rich on-chip digital effects makes it equally suitable for stereo playback and full-duplex voice-capture products.
When designing with this part, ensure both the 1.8 V digital and 3.3 V analog rails are well decoupled close to the IC, and that the PLL reference clock is selected to match the chosen MCLK frequency in software. Because the device supports both single-ended and differential microphone paths, designers should populate the unused input pins according to the datasheet reference circuit rather than leaving them floating.
This page synthesizes distributor pricing, drop-in alternatives, and practical design considerations for the TLV320AIC3106IRGZT and its sibling variants into a single design-oriented reference beyond the raw manufacturer datasheet.
ドロップイン代替品: TLV320AIC3106IRGZT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
TLV320AIC3106IRGZR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TLV320AIC3106IRGZRQ1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TLV320AIC3104IRGZR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TLV320AIC33IRGZR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TLV320AIC3206IRGZR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TLV320AIC3262IRGZR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TLV320AIC3106IRGZT 仕様
| Product Type | Stereo Audio CODEC |
| インターフェース | 24-bit PCM / I2S / DSP |
| DAC SNR | 102 dBA |
| ADC SNR | 95 dBA |
| Sample Rate Range | 8 kHz to 96 kHz |
| Digital Data Word Length | 16 / 20 / 24 / 32 bit |
| Number of Analog Inputs | 10 (programmable single-ended or differential) |
| Number of Analog Outputs | 7 |
| Headphone Amplifier Output | 40 mW into 16 ohm |
| Digital Supply Voltage | 1.8 V (1.1 V to 3.6 V tolerant digital I/O) |
| Analog Supply Voltage | 3.3 V (2.7 V to 3.6 V) |
| 動作温度 | -40 C to +85 C |
| パッケージ | VQFN-48 (RGZ) 7x7 mm with exposed thermal pad |
| 実装タイプ | Surface Mount |
| On-chip Digital Effects | 3D / Bass / Treble / 5-band EQ / AGC |
| PLL Input Frequencies | Supports 12 / 13 / 24 / 27 MHz MCLK and similar via PLL |
| RoHS ステータス | Compliant |
TLV320AIC3106IRGZT ピン構成
| ピン 1 | AVDD — Analog supply (3.3 V) |
| ピン 2 | AVSS — Analog ground |
| ピン 3 | IN1L — Left input 1 (line/mic, programmable) |
| ピン 4 | IN1R — Right input 1 (line/mic, programmable) |
| ピン 5 | IN2L — Left input 2 (line/mic, programmable) |
| ピン 6 | IN2R — Right input 2 (line/mic, programmable) |
| ピン 7 | IN3L — Left input 3 (line/mic, programmable) |
| ピン 8 | IN3R — Right input 3 (line/mic, programmable) |
| ピン 9 | MICBIAS — Microphone bias output (low-noise LDO) |
| ピン 10 | AVDD_HP — Headphone amplifier analog supply |
| ピン 11 | HPLOUT — Left headphone output (differential or cap-less) |
| ピン 12 | HPROUT — Right headphone output (differential or cap-less) |
| ピン 13 | AVDD2 — Analog supply (3.3 V, second LDO) |
| ピン 14 | LINE1L — Left line output 1 |
| ピン 15 | LINE1R — Right line output 1 |
| ピン 16 | AVSS2 — Analog ground |
| ピン 17 | AVDD3 — Analog supply (3.3 V, third rail) |
| ピン 18 | LINE2L — Left line output 2 |
| ピン 19 | LINE2R — Right line output 2 |
| ピン 20 | AVSS3 — Analog ground |
| ピン 21 | DVDD — Digital supply (1.8 V) |
| ピン 22 | DVSS — Digital ground |
| ピン 23 | MCLK — Master clock input |
| ピン 24 | BCLK — I2S bit clock (input/output) |
| ピン 25 | WCLK — I2S word clock / LRCK |
| ピン 26 | DIN — I2S data input to DAC |
| ピン 27 | DOUT — I2S data output from ADC |
| ピン 28 | SCL — I2C serial clock |
| ピン 29 | SDA — I2C serial data |
| ピン 30 | I2C_ADDR — I2C address select |
| ピン 31 | RESET_n — Hardware reset (active low) |
| ピン 32 | GPIO1 — General-purpose I/O / interrupt |
| ピン 33 | GPIO2 — General-purpose I/O |
| ピン 34 | GPIO3 — General-purpose I/O |
| ピン 35 | PLL_FLT — PLL loop filter |
| ピン 36 | PLL_VDD — PLL supply |
| ピン 37 | AVSS_PLL — PLL analog ground |
| ピン 38 | MICDET — Microphone detect / accessory bias |
| ピン 39 | HPDETECT — Headphone insertion detect |
| ピン 40 | NC — Not connected (per datasheet) |
| ピン 41 | NC — Not connected (per datasheet) |
| ピン 42 | NC — Not connected (per datasheet) |
| ピン 43 | AVSS_HP — Headphone amplifier analog ground |
| ピン 44 | MICBIAS_PWR — Microphone bias power input |
| ピン 45 | LINE3L — Left line output 3 |
| ピン 46 | LINE3R — Right line output 3 |
| ピン 47 | AVSS1 — Analog ground (additional) |
| ピン 48 | EP — Exposed thermal pad - connect to AVSS |
主な用途
TLV320AIC3106IRGZT の用途: 6 件s: Portable Media Player Audio CODEC Path, Mobile Phone and VoIP Handset Audio Interface, USB Audio Headset and Dongle, IP Phone and VoIP Speakerphone, Portable Navigation Device (PND) Audio, Digital Camera and Camcorder Audio Capture.
Portable Media Player Audio CODEC Path
The TLV320AIC3106IRGZT is well suited to portable media player (PMP) designs where stereo 44.1 kHz or 48 kHz DAC playback drives 16 ohm / 32 ohm headphones from a 3.3 V analog rail. The 102 dBA DAC SNR preserves dynamic range for lossless FLAC playback, while the integrated 40 mW headphone amplifier removes the need for an external line-driver stage, reducing BOM cost and PCB area. Designers typically route I2S BCLK / WCLK / DIN from the host application processor and let the on-chip PLL synthesize all internal clocks from a 12 MHz or 13 MHz system reference, eliminating a dedicated audio master crystal.
おすすめ
Mobile Phone and VoIP Handset Audio Interface
The TLV320AIC3106IRGZT serves as the main audio CODEC in mobile phones and VoIP handsets, providing simultaneous stereo ADC capture (for dual-mic noise cancellation) and stereo DAC playback (for earpiece and loudspeaker paths) from a single chip. The differential microphone input paths reject handset-mode common-mode noise, while the on-chip AGC block maintains consistent voice levels even when users speak at varying distances. Its low 15 mW stereo playback power from a 3.3 V supply extends battery life in always-on voice standby use cases, and the I2C / I2S digital interface ties cleanly into most application processors and baseband modems.
おすすめ
USB Audio Headset and Dongle
The TLV320AIC3106IRGZT is frequently paired with a USB audio bridge IC in USB headsets, where it performs the analog-to-digital capture and digital-to-analog playback functions at the headset end of the cable. Its stereo headphone amplifier directly drives 32 ohm headset drivers without external buffers, and the integrated microphone preamps accommodate both legacy single-ended ECM and modern differential MEMS microphones. The 16/20/24/32-bit data path with 8-96 kHz sample support matches all common USB audio class 1.0 / 2.0 profiles.
おすすめ
IP Phone and VoIP Speakerphone
The TLV320AIC3106IRGZT powers full-duplex IP phones and conference speakerphones by handling the analog microphone capture for the far-end uplink and the analog downlink to the handset / speaker amplifier. Its on-chip 3D / bass / EQ effects and 5-band parametric equalizer shape the speakerphone frequency response without burdening the DSP host, and the selectable differential inputs reject the common-mode hum that plagues desktop phones connected to building wiring. The 3.3 V analog supply is straightforward to generate from a typical 5 V or 12 V PoE rail, simplifying the power tree.
おすすめ
Portable Navigation Device (PND) Audio
PND designs use the TLV320AIC3106IRGZT to deliver clear voice prompts and stereo music playback simultaneously through the device's built-in speaker or headphone jack. The CODEC handles turn-by-turn voice prompts on the DAC path while capturing voice for hands-free Bluetooth bridge or voice command through the same ADC path. Low standby power consumption preserves battery life for handheld car-mount use, and the wide operating temperature range (-40 C to +85 C) survives the harsh automotive cabin environment.
おすすめ
Digital Camera and Camcorder Audio Capture
Digital still cameras and camcorders use the TLV320AIC3106IRGZT to capture stereo audio alongside HD video, where its 95 dBA ADC SNR preserves the dynamic range required for music or speech recording. The compact 7x7 mm VQFN-48 package fits alongside image sensor PCBs in space-constrained camera bodies, and the integrated microphone preamps remove the need for a separate audio ADC board. Differential microphone inputs reject camera body noise and motor EMI from the autofocus and zoom mechanisms, giving cleaner recordings in real-world handheld shooting conditions.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TLV320AIC3106IRGZT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV320AIC3106IRGZR | TLV320AIC3106IRGZRQ1 | TLV320AIC3104IRGZR | TLV320AIC3206IRGZR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | VQFN-48 (RGZ) 7x7 mm | VQFN-48 (RGZ) - same | VQFN-48 (RGZ) - same | VQFN-48 (RGZ) - same | VQFN-48 (RGZ) - same |
| DAC SNR | 102 dBA | 102 dBA | 102 dBA | 100 dBA | 105 dBA |
| Sample Rate Range | 8-96 kHz | 8-96 kHz | 8-96 kHz | 8-96 kHz | 8-192 kHz |
| Number of Inputs | 10 | 10 | 10 | 6 | 10 |
| Headphone Amplifier | 40 mW into 16 ohm | 40 mW | 40 mW | Lower power, no HP amp | 30 mW (improved) |
| Digital Effects Engine | Yes (3D, Bass, EQ, AGC) | Yes | Yes | Limited | Yes (enhanced) |
| Automotive Grade (AEC-Q100) | Not qualified | Not qualified | Yes (AEC-Q100) | Not qualified | Not qualified |
| Approx. Unit Price (qty 1) | $8.95 | $8.95 (slightly higher) | Higher (auto grade) | Lower ($5-6) | Higher ($10-12) |
主な差別化要因
- Highest I/O count in the TLV320AIC31xx family in the VQFN-48 footprint （vs TLV320AIC3104IRGZR)
- Enhanced on-chip digital effects (3D, bass, treble, 5-band EQ) （vs TLV320AIC3100IRGZ)
- Integrated 40 mW cap-less headphone amplifier （vs TLV320AIC3101IRGZ)
- Automotive-grade variant available in same VQFN-48 package （vs TLV320AIC3106IRGZT (this part))
設計ノート
Estimated: at 3.3 V analog, 1.8 V digital, and stereo 48 kHz DAC playback, the TLV320AIC3106IRGZT draws approximately 15 mW per the datasheet headline figure. Decouple AVDD, DVDD, MICBIAS_PWR, and PLL_VDD locally with 10 uF ceramic plus 0.1 uF high-frequency caps placed within 2 mm of each pin; inadequate decoupling on the PLL supply is a common cause of periodic clicking artifacts in the DAC output.
Keep AGND and DGND separated on the PCB and tie them together at a single point near the exposed thermal pad to avoid ground loops that inject hum into the high-impedance microphone paths. Route the MCLK line as a short, matched trace surrounded by ground to keep edge rates fast without radiating EMI; if MCLK exceeds 50 MHz, treat it as a controlled-impedance line.
Do not leave the MICBIAS output floating - always load it with the selected microphone impedance per the datasheet's biasing chart, otherwise supply ripple couples directly into the ADC path. For differential headphone drive, both HPLOUT and HPROUT must be AC-coupled to the load; in single-ended cap-less mode ensure the unused negative output is correctly terminated internally via register setting, otherwise click-and-pop on power-up will be loud.
When the on-chip PLL is used to derive internal clocks from a low-frequency MCLK (e.g., 12 MHz), the PLL_FLT loop-filter components must match the datasheet reference (typically 10 nF and 1 kohm in series-to-ground); incorrect loop-filter values will result in fractional-N spurs that degrade THD+N well below the 102 dBA SNR headline. For the cleanest measured audio performance, supply a clean audio-rate MCLK and bypass the PLL block where possible.
コンプライアンス情報
RoHS and lead-free per TI product page; not AEC-Q100 qualified - choose TLV320AIC3106IRGZRQ1 for automotive use.
