TPS54060DGQR - 60V 0.5A Step-Down Converter | Texas Instruments
部品番号: TPS54060DGQR ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $2.72 | $2.72 |
| 10 | $2.41 | $24.10 |
| 100 | $2.05 | $205.00 |
| 500 | $1.74 | $870.00 |
| 1,000 | $1.42 | $1,420.00 |
| 3,000 | $1.16 | $3,480.00 |
TPS54060DGQR 概要
A buck (step-down) converter is a switching DC-DC regulator that efficiently lowers a higher input voltage to a lower regulated output voltage by chopping the input with a power switch and averaging the resulting pulse train through an LC filter. Buck converters sit inside the broader switching regulator → DC-DC converter → power management IC hierarchy. They are preferred over linear regulators whenever the input-to-output voltage differential is large, because switching conversion avoids the linear regulator's I·(Vin-Vout) thermal loss. The TPS54060's low-quiescent Eco-Mode pulse skipping further improves light-load efficiency, making it well-suited to always-on applications.
Key features include 116 µA operating quiescent current, 1.3 µA shutdown supply current via the enable pin, internal 0.8-V reference with ±1% accuracy, frequency synchronization to an external clock, power-good output, internal soft start, cycle-by-cycle current limit, and thermal shutdown. Current-mode control provides simple external compensation and flexible component selection, allowing engineers to optimize the loop for ceramic or electrolytic output capacitors. The integrated high-side MOSFET eliminates external switch selection and reduces BOM count.
Typical applications include 24-V industrial automation rails, 48-V telecom and PoE point-of-load converters, HVAC and building automation sensor supplies, eMeter and grid infrastructure auxiliary rails, battery charging and management systems, and after-market automotive accessories operating from 12-V/24-V buses. The wide VIN range also suits distributed 12-V to 5-V/3.3-V/2.5-V intermediate buses in factory and process-control equipment.
When designing with this part, place the bootstrap capacitor (BST to SW) close to the IC and keep the high-current SW loop area minimal to reduce ringing and EMI. Use the WEBENCH Power Designer tool to generate a complete reference schematic, compensation network, and inductor selection. The PowerPAD must be soldered to a sufficient copper area for thermal dissipation — up to ~1 W is achievable with a 1-in² copper pad on a standard 4-layer FR-4 board.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the standalone manufacturer datasheet, helping engineers select, source, and qualify the TPS54060DGQR for production designs.
ドロップイン代替品: TPS54060DGQR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TPS54060DGQR （同一形状・フットプリント） — 相違点: Package, Input Voltage Range, Topology, Maximum Output Current, Output Voltage Range.
クイック比較ツール — 並列比較する代替部品を選択:
TPS54060DGQ
✅ ドロップイン✓ 在庫あり
$1.18 / 個
データシートを見る →TPS54060ADRCT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS54240DGQ
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS54360QDDARQ1
✅ ドロップイン✓ 在庫あり
$2.45 / 個
データシートを見る →TPS57160QDGQRQ1
✅ ドロップイン✓ 在庫あり
$2.98 / 個
データシートを見る →TPS54331DR
✅ ドロップイン✓ 在庫あり
$0.85 / 個
データシートを見る →TPS54302DDCR
✅ ドロップイン✓ 在庫あり
$0.42 / 個
データシートを見る →LMR16030SDDA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS54060DGQR 最大定格＆電気的特性
| トポロジー | Buck (Step-Down) |
| 入力電圧範囲 | 3.5 V to 60 V |
| 出力電圧範囲 | 0.8 V to 58 V (adjustable) |
| 最大出力電流 | 0.5 A |
| Integrated High-Side MOSFET RDS(on) | 200 mΩ |
| Switching Frequency Range | 100 kHz to 2500 kHz (external RT) |
| Control Mode | Current-Mode |
| Quiescent Current (operating) | 116 µA (Eco-Mode pulse skipping) |
| Shutdown Supply Current | 1.3 µA (EN low) |
| Internal Reference Voltage | 0.8 V (±1%) |
| 特長 | Enable, Power Good, Frequency Sync, Soft Start, UVLO, Thermal Shutdown |
| Light-Load Mode | Eco-Mode pulse skipping |
| 動作接合温度 | -40 °C to +150 °C |
| パッケージ | 10-Pin HVSSOP PowerPAD (DGQ) 3.00 mm |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
TPS54060DGQR ピン構成
| ピン 1 | VIN — Input supply voltage (3.5 V to 60 V) |
| ピン 2 | EN — Enable (active-high); pulled low disables the regulator, IQ drops to 1.3 µA |
| ピン 3 | RT — Timing resistor; sets switching frequency from 100 kHz to 2.5 MHz |
| ピン 4 | SYNC — Synchronization input; tie to external clock or to RT for standalone operation |
| ピン 5 | SS/TR — Soft-start / tracking; capacitor sets soft-start time, voltage tracking enables sequencing |
| ピン 6 | COMP — Compensation network connection for the error amplifier |
| ピン 7 | FB — Feedback input; connects to output via resistor divider (0.8 V internal reference) |
| ピン 8 | PGOOD — Power-good open-drain output; asserts when VOUT is in regulation |
| ピン 9 | BST — Bootstrap capacitor node; supplies gate-drive voltage for the high-side MOSFET |
| ピン 10 | SW — Switch node; connects to inductor, Schottky diode, and bootstrap capacitor |
| ピン 11 | PowerPAD (PGND) — Exposed thermal pad; must be soldered to PGND copper pour for thermal dissipation |
主な用途
TPS54060DGQR の用途: 7 件s: 24-V Industrial Automation Rails, 48-V Telecom and PoE Point-of-Load Converters, HVAC and Building Automation Sensor Supplies, Smart E-Meter and Grid Infrastructure Auxiliary Rails, 12-V/24-V After-Market Automotive Accessories, Battery Charging and Management Systems, Distributed 12-V to 5-V/3.3-V/2.5-V Intermediate Buses.
24-V Industrial Automation Rails
The TPS54060DGQR's 3.5-60 V input range directly accepts 24-V industrial bus voltage with substantial margin for transients, while the integrated 200-mΩ MOSFET and 0.5-A output cleanly power PLC I/O, sensor signal chains, and isolated communication transceivers. Eco-Mode pulse skipping holds quiescent current at 116 µA during standby, extending efficiency in always-on industrial nodes. According to TI's SWIFT family datasheet, the 100 kHz to 2.5 MHz adjustable switching frequency lets designers shrink inductors for DIN-rail-mounted PCBs where vertical real estate matters most.
おすすめ
48-V Telecom and PoE Point-of-Load Converters
PoE Powered Devices (PD) present a nominal 48-V input with significant cable-induced transients, and the TPS54060DGQR survives the full 60-V maximum with margin. Its high-side-only switch topology requires only a Schottky diode on the low side, simplifying synchronous-replacement architectures while keeping BOM low. Per TI's WEBENCH design tool, the 2.5-MHz max switching frequency supports the small LC filters demanded by compact PoE modules. The 1.3-µA shutdown current extends standby for IEEE 802.3az energy-efficient Ethernet compliance.
おすすめ
HVAC and Building Automation Sensor Supplies
Building automation nodes (thermostats, CO2 sensors, occupancy detectors) are often wired to 24-VAC rectified rails that present wide DC variations. The TPS54060DGQR's 3.5-60 V input tolerates these fluctuations without additional pre-regulation. Eco-Mode's 116-µA quiescent supports the long standby required by wireless battery-backed sensors. According to TI's design notes, the wide output range (0.8-58 V) allows one design to serve 3.3-V microcontroller rails, 5-V analog supplies, and 12-V actuator drivers with minor resistor-divider swaps, reducing SKU proliferation.
おすすめ
Smart E-Meter and Grid Infrastructure Auxiliary Rails
Smart electricity meters derive auxiliary power from the line voltage, producing a poorly regulated intermediate DC rail that commonly ranges from 12 V to 50 V. The TPS54060DGQR's 60-V maximum covers this range with headroom, and its internal cycle-by-cycle current limit and thermal shutdown provide the fault tolerance required for unattended grid equipment. Per TI application note SLVA477, the integrated high-side switch and small MSOP-10 footprint suit the dense PCB layouts of single-phase meter modules. Power-good output enables deterministic supervision by the meter's MCU.
おすすめ
12-V/24-V After-Market Automotive Accessories
Aftermarket automotive accessories must survive load-dump transients up to ~40 V on 12-V systems and double that on 24-V truck systems. The TPS54060DGQR's 60-V absolute maximum input absorbs these spikes without additional TVS clamping (although a TVS is still recommended for ISO 7637-2 compliance). Eco-Mode extends battery life when the engine is off, reducing parasitic drain. According to the TI SWIFT family overview, the 200-mΩ high-side MOSFET keeps junction temperature rise modest in the under-hood environment when the PowerPAD is soldered to adequate copper.
おすすめ
Battery Charging and Management Systems
Auxiliary battery chargers and DC-DC conversion stages in 12-V/24-V lead-acid or Li-ion battery stacks use the TPS54060DGQR to step the pack voltage down to logic-level rails. The wide VIN tolerates the pack's full charge voltage range, and the 1.3-µA shutdown current enables true zero-draw sleep modes. Per TI's TPS54060EVM user guide, cycle-by-cycle current limit and the soft-start pin protect battery cells against inrush faults. Power-good signaling also informs the battery management MCU of valid conversion status.
おすすめ
Distributed 12-V to 5-V/3.3-V/2.5-V Intermediate Buses
In factory and process-control equipment, a 12-V or 24-V distribution bus powers multiple lower-voltage rails through point-of-load (POL) converters. The TPS54060DGQR's 0.8-58 V adjustable output covers all common logic rails, and the small HVSSOP-10 footprint lets engineers place converters close to their loads for optimal transient response. Per TI's SWIFT family design guide, the external frequency sync capability coordinates multiple POLs to avoid beat-frequency EMI in dense cabinet layouts.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TPS54060DGQR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TPS54060DGQ | TPS54240DGQ | TPS54360QDDARQ1 | TPS57160QDGQRQ1 | LMR16030SDDA |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 10-HVSSOP PowerPAD (DGQ) | 10-HVSSOP PowerPAD (DGQ) - same | 10-HVSSOP PowerPAD (DGQ) - same | 10-HVSSOP PowerPAD (DGQ) - same | 10-HVSSOP PowerPAD (DGQ) - same | 8-SO PowerPAD - similar SMD |
| Input Voltage Max | 60 V | 60 V | 42 V | 60 V | 60 V | 60 V |
| Output Current Max | 0.5 A | 0.5 A | 2.5 A | 3.5 A | 1.5 A | 3 A |
| Quiescent Current | 116 µA | 116 µA | 136 µA | 146 µA | 116 µA | 40 µA |
| Switching Frequency Range | 100 kHz to 2.5 MHz | 100 kHz to 2.5 MHz | 100 kHz to 2.5 MHz | 100 kHz to 2.5 MHz | 100 kHz to 2.5 MHz | 200 kHz to 2.2 MHz |
| AEC-Q100 Qualified | No | No | No | Yes | Yes | No |
主な差別化要因
- Among the widest-input SWIFT family in HVSSOP-10 PowerPAD （vs TPS54240DGQ)
- Lower quiescent current for energy-starved standby （vs TPS54360QDDARQ1)
- Single-SKU multi-output versatility (0.8-58 V adjustable) （vs TPS57160QDGQRQ1)
設計ノート
The TPS54060DGQR's HVSSOP PowerPAD is the primary heat-dissipation path; the datasheet specifies RθJA of approximately 50 °C/W on a 4-layer JEDEC test board with 1-in² PowerPAD copper. Per TI's layout guide (SLVA477), keep the high-current SW loop (VIN → internal MOSFET → SW → external diode → PGND) tight, place the bootstrap capacitor (BST-to-SW) within 5 mm of pins 9-10, and use a PGND copper island under the IC connected to PowerPAD with multiple thermal vias. Failing to observe these can add 20 °C of junction rise and reduce efficiency 2-3% at full load.
Estimated: at VIN=24 V, VOUT=5 V, IOUT=0.5 A, power dissipation is approximately (24-5) × 0.5 + VIN × IQ ≈ 9.6 W. With the integrated 200-mΩ MOSFET and 90% typical efficiency, junction rise should remain manageable on a 1-in² copper pad. For VIN-VOUT differentials above 15 V at full load, derate output current or add airflow; the thermal shutdown threshold (~165 °C junction) protects against catastrophic failure but should not be relied on in normal operation.
Do not omit the bootstrap capacitor (typically 0.1 µF X7R between BST and SW) — without it the high-side MOSFET lacks gate drive and the regulator will not start. Ensure the EN pin is pulled above the rising threshold (~1.2 V) for reliable startup across temperature. The SS/TR pin must have a capacitor (typically 10-100 nF) to limit inrush; do NOT leave SS/TR floating. In Eco-Mode, the SW node stays low until the next pulse, so ripple may slightly increase at microamp loads — this is normal, not a fault.
For EMI-sensitive designs, place the input bulk capacitor close to VIN (pin 1) and connect its return directly to the PowerPAD/PGND copper island to minimize the input current loop. Use an external SYNC clock to set a fixed frequency that avoids sensitive bands (e.g. 400 kHz for AM-bands, 1.7 MHz for shortwave). The datasheet suggests shielded ferrite inductors and a snubber (RC across the Schottky) can further reduce SW-node ringing by 5-10 dB at 100-200 MHz.
コンプライアンス情報
RoHS compliant per TI datasheet. Standard DGQR is industrial/consumer grade; for AEC-Q100 qualification choose TPS54060QDRCRQ1 (different VSON-10 package, NOT a drop-in).
