RF 모듈
제품 (294)
JN5179/001Y - ZigBee 3.0 Wireless MCU 512kB Flash | NXP
The NXP Semiconductors JN5179/001Y is an ultra-low-power, high-performance wireless microcontroller SoC optimized for ZigBee 3.0 applications in smart home and smart lighting networks, integrating an Arm Cortex-M3 core, 512 kB flash, and a 2.4 GHz IEEE 802.15.4 radio transceiver in a single 40-pin VFQFN exposed-pad package. A wireless microcontroller SoC (System-on-Chip) is a category of integrated circuit that combines a microcontroller CPU, memory, peripherals, and a radio transceiver on a single die. Within the broader semiconductor hierarchy, it sits as: wireless MCU -> microcontroller (MCU) -> integrated circuit -> semiconductor. Wireless MCUs are purpose-built to run protocol stacks such as Zigbee, Thread, or Bluetooth Low Energy directly, removing the need for a separate host processor and external radio module. The JN5179 integrates an Arm Cortex-M3 processor core with debug support, programmable clock speeds, 512 kB of embedded flash, and a 2.4 GHz IEEE 802.15.4 compliant radio. Per the NXP product page, the JN5179 family also features an integrated power amplifier and is engineered for low active and sleep current consumption, which is critical for battery-powered end-node designs in home automation. Note that NXP's official guidance recommends JN5189/88T for new designs and no new software releases are planned for JN5179. Architecturally, the JN5179 consolidates the radio baseband, modem, MAC accelerator, application CPU, memory, and peripherals so that developers can implement full Zigbee 3.0 nodes (coordinator, router, or end device) without companion chips. The 40-VFQFN exposed-pad variant (suffix /001Y) improves thermal dissipation and allows the device to handle the radio TX power amplifier currents reliably. Typical applications include Zigbee 3.0 smart light bulbs, smart plugs, wireless sensors, home gateways/routers, and smart lighting bridges. The integrated PA simplifies single-ended antenna matching for low-cost PCB antenna designs in compact bulb form factors. Designers must check that their target power supply can deliver the peak TX current pulses without excessive droop, place a solid ground plane under the exposed pad, and follow NXP's reference layout for the RF matching network. New designs are advised to consider the recommended JN5189/88T successor. This page synthesizes distributor pricing, parametric specs, and drop-in family alternatives compiled from the NXP product page and authorized distributor listings - information not aggregated in the standalone datasheet.
JNP-SFPP-10GE-T-C - 10GBASE-T SFP+ Copper 30m RJ-45 Transceiver
The JNP-SFPP-10GE-T-C is a multi-rate 100M/1G/10GBASE-T copper SFP+ transceiver with an RJ-45 interface, supporting 10 Gigabit Ethernet auto-negotiation over twisted-pair cabling up to 30 m. Housed in a hot-pluggable SFP+ form factor, it draws 3.3 V supply power and is marked for commercial temperature operation, making it a flexible drop-in replacement for legacy 1G SFP RJ-45 links on Juniper switching and routing platforms. A 10GBASE-T SFP+ copper transceiver is a small-form-factor-pluggable module that converts a host SFP+ cage electrical interface into 10 Gigabit Ethernet signalling over Category 6a/7 twisted-pair copper. It sits within the broader hierarchy: SFP+ module -> copper transceiver -> 10GBASE-T PHY -> Ethernet PHY -> physical layer device (PHY) -> networking IC. Copper SFP+ transceivers provide a low-cost, low-latency alternative to fibre SFP+ optics for short-reach top-of-rack and intra-rack links. Key features include multi-rate auto-negotiation (100 Mbps, 1 Gbps, and 10 Gbps), 30 m reach over Cat 6a/7 cabling, RJ-45 connector, 3.3 V single-rail power supply, hot-pluggable SFP+ footprint, and digital diagnostic monitoring (DOM/DDM) readouts including temperature, supply voltage, and link status. The module conforms to the SFF-8431 SFP+ MSA electrical interface. Technically, the module integrates a 10GBASE-T PHY plus an RJ-45 magnetics assembly. It relies on the host switch's SFP+ cage for I2C-based management and DOM telemetry. Because copper SFP+ modules consume more power than their fibre counterparts (typically around 2.5-3 W at 10G), thermal headroom in the host chassis should be evaluated before deployment at high port density. Typical applications include Juniper EX/QFX/MX switch top-of-rack to server 10G links, in-rack copper aggregation replacing SFP+ DAC cables, and drop-in replacement for end-of-life JNP-SFPP-10GE-T optical transceivers where fibre runs are not required. It is also used to bridge legacy 1G copper SFP links to 10G-capable switches without re-cabling. When designing with this part, verify that the host switch firmware and Hardware Compatibility Tool (HCT) listing accept 3rd-party compatible SFP+ modules; many enterprise switches enforce a DOM signature or vendor lock. Estimate power budget against host SFP+ cage ratings (typically 1 to 3.5 W) before populating all ports. This page consolidates JNP-SFPP-10GE-T-C pricing, drop-in compatible alternatives, and deployment notes beyond what the manufacturer compatibility matrix offers.
K32W041AM-A - Wireless MCU, Arm Cortex-M4, BLE 5.0/Zigbee/Thread | NXP
The NXP K32W041AM-A is an ultra-low power, high-performance Arm Cortex-M4 based wireless microcontroller integrating a 2.4 GHz Bluetooth Low Energy 5.0 transceiver, a 2.4 GHz IEEE 802.15.4 transceiver (for Zigbee 3.0 and Thread), and NFC connectivity in a single 40-pin VFQFN-Exposed-Pad package. It supports up to eight simultaneous BLE connections and contains 640 KB embedded Flash, 152 KB RAM, plus an additional 1 MB data Flash unique to the K32W041AM variant, enabling Over-the-Air (OTA) firmware updates for connected devices. A wireless microcontroller (wireless MCU) is a single-chip system that combines a microcontroller core with one or more radio transceivers, eliminating the need for a separate network processor. The K32W041AM-A belongs to the integrated wireless SoC family within the broader MCU hierarchy: wireless MCU > mixed-signal MCU > microcontroller > semiconductor. This category targets low-power connected nodes where PCB area, BOM cost, and coin-cell battery lifetime are critical design constraints. Key features include ultra-low current consumption in radio receive and transmit modes, a comprehensive mix of analog and digital peripherals, hardware crypto accelerators supporting Thread/Zigbee security, and expanded memory optimized to facilitate home and building automation, smart lighting, smart locks, gateways, and routers. The device is compatible with the K32W061/41 family for designs requiring migration or memory flexibility. The architecture leverages an Arm Cortex-M4 core running at up to 48 MHz, paired with dedicated radio hardware offloads. The device implements secure boot, secure firmware update, and hardware-accelerated AES-128/256, supporting the cryptographic requirements of Zigbee 3.0 and Thread networking stacks without burdening the application CPU. Typical applications include wireless smart lighting, smart locks and access control, home automation gateways, Thread border routers, BLE mesh lighting nodes, NFC-touch commissioning, and battery-powered sensor networks. The 1 MB data Flash on the K32W041AM variant specifically enables OTA-updatable end products requiring non-volatile user data storage or multi-image firmware banking. When designing with this device, follow NXP's reference design for RF matching network component values; PCB layout for the 2.4 GHz radio section follows JESD-79 style controlled-impedance guidelines with ground pour stitching. Always validate RF performance with the K32W041AM-A evaluation kit and respect the antenna keep-out region around the QFN thermal pad. This page synthesizes manufacturer datasheet specifications, distributor pricing, and practical drop-in compatibility notes not found in the standard NXP product brief.
K32W061K - Ultra-Low-Power Wireless MCU 802.15.4/BLE 5.0 | NXP
The NXP K32W061K is a high-performance, ultra-low-power wireless microcontroller (SoC) that supports IEEE 802.15.4 (Zigbee, Thread, Matter) and Bluetooth Low Energy 5.0 in the 2.4 GHz band. It is housed in a 40-pin VFQFN exposed-pad package and includes an Arm Cortex-M4 application processor, a separate Cortex-M0+ network coprocessor, and built-in NFC option for commissioning. The device is designed to power the next generation of ultra-low-current multiprotocol wireless IoT nodes. A wireless SoC (System-on-Chip) integrates an MCU core, memory, peripherals, and a radio transceiver on a single die. In the connectivity hierarchy it sits above discrete MCU + external radio designs, enabling BOM reduction and lower PCB area. Within the K32W061/41 portfolio, the K32W061K is the standard Flash/RAM configuration while the K32W041K provides reduced memory, both targeting multi-protocol matter-ready smart home, lighting, and sensor networks. Key features include a Cortex-M4 core running up to 48 MHz with up to 640 kB Flash and 152 kB SRAM, integrated 2.4 GHz RF transceiver for 802.15.4 and BLE 5.0, hardware AES-128/256 crypto engine, integrated DC-DC converter supporting 1.9 V to 4.5 V battery operation, and an on-package antenna-matching network. The exposed thermal pad enables direct PCB heatsinking for high-duty-cycle applications, while ultra-low sleep current extends coin-cell battery life. Architecture-wise, the device splits workloads: the M4 application core handles Zigbee/Thread/Matter application logic and OTA updates, while a dedicated radio coprocessor manages time-critical 802.15.4 packet timing. This dual-core partitioning avoids jitter-induced RF failures common in single-core designs and supports concurrent multi-protocol operation (PANC/RCP), enabling Zigbee + BLE coexistence in a single node. Typical uses are Matter/Zigbee/Thread end nodes (light bulbs, dimmers, sensors), BLE 5.0 beacons, NFC-commissioned door locks, battery-powered remote controls, and Thread Border Router companions. Pin-compatible variants in the K32W family share the same 40-VFQFN footprint, allowing PCB reuse across SKUs with different memory sizes or NFC options. Design consideration: maintain a 50 Ω RF trace to the antenna with π-attenuation pads for matching, keep the DC-DC inductor within 5 mm of the SW pin, and place the 32 kHz crystal within 2 mm of the XTAL pins to minimize load-capacitance drift. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
KCM0A5S - Wi-SUN FAN 1.1 Sub-GHz Mesh Module | Quectel
The Quectel KCM0A5S is a high-performance Wi-SUN FAN 1.1 wireless mesh networking module operating in the 470 MHz to 928 MHz sub-GHz band (902 MHz to 928 MHz on the DigiKey-listed KCM0A5SACMD-0L-02 variant), built on a Silicon Labs EFR32FG25 ARM Cortex-M33 processor running at up to 97.5 MHz with 256 KB RAM and 2 MB Flash, housed in a 22 x 28 mm LCC surface-mount package powered from 3.45 V to 5.5 V. Wi-SUN (Wireless Smart Utility Network) is an IPv6-based low-power wide-area mesh networking standard defined by the Wi-SUN Alliance under IEEE 802.15.4g. Unlike star-topology LPWAN technologies, Wi-SUN forms self-healing mesh networks in which each node can relay traffic for its neighbors, extending coverage over large areas such as utility districts and city grids while remaining tolerant of individual node failures. The KCM0A5S implements Wi-SUN FAN 1.1, adding features over FAN 1.0 such as enhanced security, expanded device classes, and improved network scalability. Adaptive frequency hopping provides strong resistance to interference in congested unlicensed sub-GHz spectrum, while the mesh architecture delivers high network capacity and long-range transmission for dense IoT deployments. Optimized for battery-powered operation, the module combines the low-power EFR32FG25 radio SoC with Quectel firmware supporting the full Wi-SUN FAN 1.1 protocol stack, letting developers integrate mesh connectivity through a serial host interface without implementing the RF stack themselves. The Cortex-M33 core also provides headroom for application-level processing and AES-128-CCM security operations required by the Wi-SUN specification. Typical applications include smart electricity, water, and gas metering, smart street lighting, precision agriculture, industrial IoT sensor networks, and smart-city infrastructure. Long battery life, multi-year mesh stability, and 470 MHz to 928 MHz regional band coverage make the module well suited to deployments lasting a decade or more. Designers should verify the regional frequency variant (470 MHz China band vs 902-928 MHz FCC band) before board layout, and reserve antenna clearance since the antenna is not included on module variants. Supply rails of 3.45 V to 5.5 V allow direct connection to lithium primary cells or 5 V logic supplies. This page synthesizes verified distributor data, the official Quectel specification, Wi-SUN Alliance certification listing, and practical design guidance not found in the manufacturer datasheet.
KGM133S - 78MHz Cortex-M33 Matter/Thread/Zigbee/BLE Module | Quectel
The Quectel KGM133S is a high-performance, low-power wireless MCU module integrating an ARM Cortex-M33 processor clocked up to 78 MHz with multi-protocol 2.4 GHz radio support for Matter, Thread, Zigbee, Bluetooth LE 6.0, and BLE mesh in a compact surface-mount LGA package. It targets connected lighting, smart home, smart building, and industrial IoT nodes where developers need a single certified module that interoperates across the major low-power mesh ecosystems without external MCU support. An MCU-integrated wireless module like the KGM133S belongs to a broader family of short-range radio modules that combine an application processor and a 2.4 GHz transceiver on a single PCB. Within the system hierarchy it sits inside the IoT/connected-device stack, which itself spans modules, transceivers, MCUs, and full SoCs; for engineers building Matter-compliant end devices, the module layer eliminates the FCC/CE pre-certification work that a bare chip would otherwise require. Key features include 78 MHz Cortex-M33 compute, IEEE 802.15.4 PHY support for Thread and Zigbee, BLE 6.0 dual-role, BLE mesh 1.x, integrated antenna variants, and an operating temperature range that spans industrial deployments. Variants like KGM133SABTB and KGM133SABMD offer different antenna and certification bundles, while KGM133S-P is the LGA-only variant without integrated antenna for embedded designs. Architecturally, the module integrates a Cortex-M33 core, a 2.4 GHz radio transceiver supporting OQPSK/8-FSK modulations for 802.15.4 and GFSK for BLE, on-module crystal and matching network, and a low-power sleep path that lets battery-powered nodes achieve multi-year coin-cell runtime. The integration removes RF design risk for the host product team. Typical applications include Matter-over-Thread smart lighting, Zigbee home automation gateways and end devices, BLE mesh building automation, and battery-powered wireless sensors. Industrial use cases such as asset tracking and predictive-maintenance beacons also fit thanks to the industrial operating range. When designing with the KGM133S, ensure the host PCB keeps the antenna keep-out zone clear, follow the Quectel reference layout for the LGA footprint, and select the matching variant (integrated PCB antenna vs U.FL connector) for the enclosure. Compliance with regional RF rules is preserved only when the host follows Quectel's reference design. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and second-sourcing the KGM133S family.
KSZ9893RNXC-TR - 3-Port Gigabit Ethernet Switch, 64-VQFN | Microchip
The Microchip Technology KSZ9893RNXC-TR is a fully integrated layer-2 managed three-port Gigabit Ethernet switch in a 64-pin VQFN (8x8 mm) package, supporting 10/100/1000 Mbps on two PHY ports and a third configurable RGMII/MII/RMII interface port. The device integrates two 10/100/1000 Base-T PHYs, a non-blocking store-and-forward switch fabric, and an internal frame buffer suitable for managed-switch applications with QoS and VLAN support. A managed Ethernet switch is a layer-2 networking IC responsible for connecting end devices on the same local area network. Within the broader taxonomy, microchip ISZ9893RNXC-TR falls under Ethernet switch IC -> network interface controller -> communication IC -> semiconductor. These switches typically sit on the same PCB as a host processor (via SPI/I2C/MII/RGMII), handling MAC-layer frame forwarding, address learning, queueing, and traffic classification while offloading these tasks from the application CPU. Key features include support for Energy Efficient Ethernet (EEE), Wake-on-LAN (WOL), Quality of Service (QoS), LinkMD cable diagnostics, and MIB counters for network telemetry. The KSZ9893RNXC-TR is configured via SPI or I2C management interfaces and supports IEEE 802.1Q VLAN, 802.1p priority, and 802.3x flow control. Two of the three ports are full PHY transceivers with HP Auto-MDI/MDIX, while the third port exposes RGMII/MII/RMII to an external MAC or SoC. Architecturally, the KSZ9893R family uses a 1.2 GHz SerDes core for the integrated PHYs, with on-chip termination and adaptive equalization for 1000BASE-T operation over CAT5e cable. The store-and-forward fabric supports 12K-entry address lookup and 4 priority queues per output port. Per-port egress shapers and rate limiting use leaky-bucket algorithms, and the device integrates PTP hardware timestamping for IEEE 1588 applications when configured with external 25 MHz reference. Typical applications include standalone 10/100/1000 Mbps Ethernet switches, VoIP infrastructure switches, Wi-Fi access-point gateways, industrial control switches, broadband gateways, networked measurement and control systems, and security/surveillance systems. The integrated PHY count reduces external magnetics and RJ-45 count, simplifying the BOM for 2+1 + fan managed Gigabit designs. Designers should ensure the 25 MHz reference clock source is within ±50 ppm to meet 1000BASE-T jitter requirements, and follow Microchip reference schematics for the central-tap magnetics and 49.9 ohm termination. The device requires 1.2 V and 3.3 V supplies; both rails should be decoupled with 10 uF + 0.1 uF capacitors near the package. This page synthesizes distributor pricing for the KSZ9893RNXC-TR, drop-in package-compatible variants, and practical design notes not aggregated on any single distributor page, giving engineers a one-stop reference for selecting and laying out this Ethernet switch IC.
LARA-R202-02B - LTE Cat 1 Multi-Mode Cellular Module | u-blox
The u-blox LARA-R202-02B is a multi-mode LTE Cat 1 / 3G / 2G cellular transceiver module that delivers up to four LTE bands, two UMTS/HSPA bands, and two GSM/EGPRS bands in a compact 24x26 mm LGA castellation surface-mount package. As an AT&T and T-Mobile carrier-certified module, it supports LTE bands B2, B4, B5, and B12 plus 3G fallback on B2/B5, making it ideal for North American M2M, asset tracking, and IoT deployments. The antenna is not included on the module, giving designers freedom to choose a tuned trace, ceramic, or external antenna for their mechanical enclosure. A cellular module (also called a radio module, transceiver module, or modem) is a self-contained subsystem that integrates the cellular baseband, RF transceiver, power management, and SIM interface on a single PCB. Cellular modules sit at the top of the embedded connectivity hierarchy, abstracting cellular protocol complexity from the host MCU. Within the u-blox LARA family, the R2 series is the size-optimized LTE Cat 1 multi-mode line, positioned between the lower-cost SARA Cat 1 modules and the higher-bandwidth TOBY LTE Cat 6 modules. Key features include integrated TCP/IP, HTTP, FTP, TLS, and MQTT stacks via the u-blox AT command set, support for GNSS operation in parallel through dedicated host-controlled interfaces, and a USB 2.0 interface for high-throughput diagnostics and firmware updates. The module operates over the industrial -40C to +85C temperature range, supports 3.3V to 4.4V supply input, and exposes UART, SPI, I2C, and USB host interfaces for host MCU integration. The LARA-R2 architecture pairs a Qualcomm MDM6200/MDM9x07-class baseband with a u-blox-tuned RF front end. Internal signal pull-ups added during the -02B revision (documented in u-blox PCN UBX-17062827) eliminate rare low-temperature diagnostic glitches. The LARA form factor shares pinout compatibility with SARA and TOBY modules, allowing PCB reuse across product families. Typical applications include fleet and asset tracking, point-of-sale terminals, connected health devices, smart metering, industrial telemetry, and alarm/security panels. The AT&T and T-Mobile certifications make drop-in network approval straightforward for North American IoT product launches. The module is also widely adopted for connected vending, EV charging station telemetry, and remote sensor gateways. Designers should size the host PCB clear-out keep-out area below the antenna feed, ensure the SIM card holder is within 10 cm of the SIM pins, and add a TVS diode array on the USB lines for surge protection. For regulatory compliance, the end device must undergo FCC/PTCRB certification with the chosen antenna, even if the module itself is pre-certified. This page synthesizes verified distributor pricing, same-family cross-brand drop-in alternatives, and practical design notes compiled by XAIPART that go beyond what appears in the standalone u-blox datasheet. Sources include DigiKey, Mouser, LCSC, and the official u-blox system integration manual.
LARA-R202-03B - LTE Cat 1 / HSPA+ Cellular Module | u-blox
The u-blox LARA-R202-03B is a size-optimized LTE Cat 1 / 3G / 2G multi-mode cellular transceiver module in an LGA-100 castellation surface-mount package, designed for North American US-Cellular and T-Mobile networks. It supports four LTE bands (B2, B4, B5, B12), two UMTS/HSPA+ bands (B2, B5), and two GSM/EGPRS bands with peak downlink data rates up to 10.3 Mbps. The module operates from a 3.8 V nominal supply and integrates the cellular baseband, RF transceiver, and power management in a compact 26.0 x 24.0 mm form factor. An LTE Cat 1 cellular module is a 4G LTE category-1 device class that delivers up to 10 Mbps downlink / 5 Mbps uplink over LTE, balancing throughput and power for IoT applications that exceed Cat-M1 or NB-IoT bandwidth but do not need full broadband speeds. Cellular modules sit in the connectivity hierarchy between simple short-range radios (Wi-Fi, Bluetooth) and full smartphone-class LTE modems, and they belong to the broader category of RF transceiver modules that combine RF front-end, baseband processor, and protocol stack into a single pre-certified surface-mount unit. The LARA-R2 family specifically targets industrial IoT, telemetry, and asset-tracking products requiring reliable wide-area connectivity. Key features include multi-band LTE/HSPA+/GSM support, integrated TCP/IP and UDP/IP stacks, USB 2.0 device interface, UART, and AT-command control via u-blox's well-documented AT interface. The castellation LGA-100 footprint enables standard reflow soldering, while the surface-mount design simplifies manufacturing compared to older module generations that required castellated through-hole assembly. The module is designed for industrial temperature ranges and is pre-certified by major North American carriers, eliminating the need for operator-specific PTCRB/GCF certification when properly integrated into an end device. Typical applications include asset tracking and fleet management, smart metering, vending machine telemetry, industrial sensor gateways, and connected health devices. The LARA-R202-03B specifically targets US-Cellular and T-Mobile LTE coverage, making it well-suited for North American IoT deployments where those carriers' LTE Band 12 700 MHz spectrum is critical for indoor and rural penetration. When designing with this module, ensure antenna selection matches the supported frequency bands, and provide adequate thermal relief since the LGA package dissipates heat through the PCB land pattern. The u-blox EVK-R2 evaluation kit accelerates integration, and developers can use u-blox's m-center cellular evaluation software for AT-command testing. This page synthesizes real-time distributor pricing, LARA-R2 family alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.
LBAA0QB1SJ-296 - LoRaWAN Sub-GHz Module 868/915MHz | Murata
The Murata Electronics LBAA0QB1SJ-296 (Type 1SJ) is a compact LoRaWAN transceiver module operating in the 868 MHz and 915 MHz sub-GHz ISM bands from a 2 V to 3.6 V supply, delivering up to 21.5 dBm output power and -137 dBm receiver sensitivity in a surface-mount package. A LoRaWAN module is a complete long-range, low-power wireless radio subsystem that integrates a sub-GHz RF transceiver, antenna matching network, and modem firmware on a single certified land-pattern device. Within the LPWA (Low Power Wide Area) connectivity hierarchy, it sits above bare RF chips and below complete end-node systems, letting engineers add km-range telemetry to sensors, meters, and trackers without designing an RF section or navigating radio-equipment certification from scratch. Key features include one of the smallest footprints in the industry for a LoRaWAN module, lower power consumption and higher RF output than previous Murata generations, radio law certification already obtained for major regions, and preloaded modem software for the US915 band that is controlled entirely through simple AT commands. Receiver current is typically 15.5 mA to 20 mA, making the module suitable for coin-cell and battery-powered nodes. At its core the module is built on the Semtech SX1262 LoRa chipset, which provides the LoRa spread-spectrum modulation, high link budget, and up to +21.5 dBm transmit power. Murata integrates the RF front end, crystal reference, and matching network, then validates the design against regional radio regulations so customers inherit a certified RF chain. Typical applications include smart utility metering on US915 LoRaWAN networks, battery-powered asset tracking, smart agriculture sensor nodes, and industrial IoT gateways-to-node links where multi-kilometer range and multi-year battery life are required. For design success, allocate a ground plane under the module, follow the Murata recommended land pattern, and account for the 2 V to 3.6 V supply window - a regulated 3.3 V rail is the natural choice. Antenna is not included on the -296 variant, so plan RF feed and antenna matching on the host PCB. This page synthesizes distributor pricing, firmware-variant comparison (-295 vs -296), and practical design notes not found in the manufacturer datasheet.
LBAD0XX1SC-NTN - LTE Cat M1/NB-IoT NTN Module | Murata
The Murata LBAD0XX1SC-NTN (Type 1SC-NTN) is a Cat M1/NB-IoT LPWA cellular module with integrated Rel-17 Non-Terrestrial Network (NTN) satellite communication support, GNSS positioning, and integrated SIM, housed in an 11.1 x 11.4 x 1.5 mm silver resin-shielded surface-mount package. An LPWA (Low Power Wide Area) cellular module is a wireless communication subsystem that connects IoT devices to LTE Category M1 (LTE-M) and NB-IoT networks optimized for low data rates, deep coverage, and multi-year battery life. Within the system hierarchy, an LPWA module sits between the host MCU and the cellular antenna, handling RF transceiving, protocol stack execution, and network registration so the host processor only sees an AT command or OpenMCU interface. Key features of the Type 1SC-NTN include the world's smallest Cat. M1/NB-IoT footprint with global certification, seamless Rel-17 NTN satellite connectivity via Skylo technology that requires no hardware design changes, support for GPS/GNSS positioning, an Integrated SIM (iSIM) option, and Murata's OpenMCU capability that lets the module host application code directly. The module operates in the LTE low band (699 MHz to 915 MHz) and mid band (1.71 GHz to 2.025 GHz) and is optimized for 3GPP class 3 output power of +23 dBm. Architecturally, the module comprises an Altair ALT1250 transceiver paired with an FEM (front-end module) and external flash memory, all integrated behind Murata's silver resin shield. This single-package integration minimizes external BOM count, simplifies RF layout, and reduces time-to-market for IoT device makers. Regulatory certifications include FCC/IC, ETSI, and TELEC, plus PTCRB and GCF operator certifications, enabling worldwide deployment on a single design. Typical applications include asset tracking that roams beyond terrestrial coverage, smart utility metering, agricultural and maritime sensors, and fleet telematics where uninterrupted communication - anytime, anywhere - is a requirement. The NTN capability is especially valuable where terrestrial LTE-M/NB-IoT coverage is unavailable or unreliable. When designing with this module, follow Murata's recommended land pattern exactly; datasheet guidance notes that characteristics can vary with land dimensions, NC-terminal grounding method, and PCB material and thickness. Antenna is not included, so plan an external antenna with a 50-ohm matched feed. This page synthesizes distributor availability data, NTN capability details, and practical design guidance not consolidated in the manufacturer datasheet, along with drop-in family alternatives and application pairing recommendations.
LBAD0XX1SC-SFS - LTE Cat M1/NB-IoT Module | Murata
The Murata LBAD0XX1SC-SFS (Type 1SC-SFS) is an LTE Cat M1 / NB-IoT cellular LPWA transceiver module with +23 dBm Class 3 LTE output power, integrated GNSS positioning support, and a compact 11.1 x 11.4 x 1.5 mm (max) silver resin shielded package with LGA-style surface-mount lands. An LPWA (Low Power Wide Area) module is a type of cellular connectivity subsystem that sits within the wireless module hierarchy: transceiver module -> cellular IoT module -> RF & wireless component. LPWA technologies such as LTE-M (Cat M1) and NB-IoT trade peak throughput for dramatically lower power consumption and superior deep-indoor penetration, making them the dominant connectivity choice for battery-powered IoT devices that must communicate over licensed cellular spectrum for 10 or more years on a single battery. Key features of the LBAD0XX1SC-SFS include dual-mode LTE Cat M1 and NB-IoT operation, a user-friendly AT command interface for seamless host integration, and ultra-low-power eDRX and PSM sleep modes that enable 10+ year battery life as stated by Murata. The module integrates the Altair ALT1250 transceiver together with a FEM (front-end module) and external flash memory, so the host board needs only an antenna and minimal external circuitry. On the technical side, the module uses an integrated TCXO (temperature-compensated crystal oscillator) with robust low-drift thermal characteristics, which removes the need for an external oscillator and preserves RF accuracy across the full industrial temperature range. RF coverage spans low and mid LTE bands (699 MHz to 915 MHz and 1.71 GHz to 2.025 GHz per DigiKey listings), and the module is optimized for 3GPP release-compliant Class 3 +23 dBm output power. Murata also highlights support for GPS/GNSS, OpenMCU, Integrated SIM, and NTN (non-terrestrial network) operation in the Type 1SC family. Typical applications include battery-powered smart utility meters, asset trackers, smart-city sensors, and industrial telemetry endpoints where multi-year battery life and global cellular certification (FCC/IC, ETSI, TELEC, PTCRB, GCF) shorten time to market. Design consideration: place the module antenna feed with a controlled 50-ohm trace and follow Murata's recommended land pattern exactly, since the shielded LGA construction relies on the PCB ground plane for RF and thermal performance. This page synthesizes verified manufacturer and distributor data, pricing structure, drop-in family variants, and practical design notes not found in the datasheet alone. Pricing shown reflects availability as of 2026-10-19.
LBAD0XX1WG-EVK-TEMP - LTE Cat M1 Evaluation Kit | Murata
The Murata LBAD0XX1WG-EVK-TEMP is a temperature-qualified evaluation kit for the Type 1WG (LBAD0XX1WG) LTE Cat M1 cellular LPWA module, designed to accelerate development of battery-powered IoT devices that connect over LTE-M networks. The underlying module operates from a 2.85 V to 4.35 V supply, supports receive levels down to -23 dBm, and uses an external antenna configuration, all packaged in a compact LGA-format shielded construction. An LTE Cat M1 module is a cellular LPWA (Low Power Wide Area) modem that implements 3GPP LTE-M protocols, sitting within the broader hierarchy of cellular connectivity: cellular modem -> LTE LPWA module -> wireless connectivity module -> IoT communication device. LTE Cat M1 is optimized for machine-type traffic where ultra-low power, deep coverage, and 10+ year battery life matter more than throughput, distinguishing it from Cat NB1/NB-IoT (narrowband, reduced mobility) and standard LTE (high throughput, high power). Key features evidenced across the Type 1WG/1SC family include 3GPP eDRX and PSM power-saving modes, hibernation power of just 3 uA, eDRX power below 45 uA at 8 hyperframes, and a configurable dormant window in PSM mode. These modes collectively enable the quoted battery life of up to 10+ years for small battery-operated IoT devices. The module family also supports over-the-air (OTA) firmware update, eliminating field-recall costs during deployment. The Type 1SC sibling measures just 11.1 x 11.4 x 1.5 mm and integrates an Altair ALT1250 transceiver, FEM, external flash, and a low-drift integrated TCXO in a silver resin shielded package, indicating the integration density of this product line. Typical applications for this evaluation platform include smart utility meters, asset trackers, smart-city sensors, and industrial telemetry nodes - anywhere a small, battery-operated device must maintain multi-year cellular connectivity. Engineers use the EVK to validate RF performance, characterize current consumption across PSM/eDRX states, and prototype network registration and OTA update flows before committing to custom PCB layouts. When designing with the Type 1WG module, pay close attention to supply-voltage sequencing and current-profile headroom: even though average current is microamps, transmit bursts require the 2.85 V to 4.35 V supply rail to remain stable under pulsed load, so input capacitance and battery internal resistance must be characterized. This page synthesizes verified manufacturer product data, distributor listings, and practical evaluation guidance for the LBAD0XX1WG-EVK-TEMP that is not consolidated on the manufacturer datasheet alone.
LBAD0ZZ2GD-EVK - LTE-M/NB-IoT Cat.M1 Eval Kit | Murata
The Murata LBAD0ZZ2GD-EVK is an evaluation kit for the Type 2GD (LBAD0ZZ2GD) LTE Cat.M1/NB2 cellular IoT module, an ultra-small, ultra-low-power LPWA module that integrates the LTE SoC, RF front end, crystal, and SRAM and flash memory in a compact LGA package. The kit enables engineers to prototype, test, and certify 3GPP Rel-14 LTE-M and NB-IoT connectivity before committing to a custom PCB design. An LPWA (Low Power Wide Area) module is a type of cellular communication module belonging to the broader hierarchy of connectivity module -> RF module -> IoT communication device. LTE Cat.M1 (LTE-M) and NB-IoT are licensed-band 3GPP standards designed for battery-powered IoT devices that prioritize minimal cost and power consumption over throughput; LTE-M provides approximately 1 Mbps upstream and 1 Mbps downstream, and both standards support mobility, making them suitable for moving devices with reduced radio interference compared with unlicensed-band solutions. Key features of the underlying LBAD0ZZ2GD module include 3GPP Rel-14 compliance, dual-mode LTE-M/NB2 operation, 8 MByte of flash memory, and low-power modes including PSM (Power Saving Mode) and eDRX (extended Discontinuous Reception). Murata states its compact LPWA module family achieves power consumption as low as 1.5 uA in Power Saving Mode, which is a central reason for selecting this platform for battery-powered designs. The module uses an external antenna configuration and an LGA surface-mount land pattern per Murata standard recommendations. Technically, the Type 2GD integrates the complete signal chain on a single substrate: the LTE SoC handles baseband and protocol processing, the RF front end drives the external antenna, and integrated SRAM and flash eliminate external memory BOM items. Because the RF front end, crystal, and memory are pre-integrated and pre-tested, designers avoid the most difficult RF layout tasks and inherit Murata's certification baseline, with the module carrying FCC ID HSW-TY2GD via Murata Electronics North America. Typical applications evaluated with this kit include smart utility metering, asset tracking, smart city infrastructure, industrial sensors, and battery-powered telemetry nodes. The evaluation kit lets developers exercise PSM/eDRX duty cycles and measure real current profiles before finalizing the power budget. A key design consideration: Murata's datasheet notes that module characteristics vary depending on land pattern drawing method, grounding method, land dimensions, NC-terminal land forming, and PCB material and thickness, so the EVK-provided reference layout should be followed closely when transitioning to production. This page synthesizes distributor data, verified web sources, and practical integration guidance for the LBAD0ZZ2GD-EVK not consolidated in the manufacturer datasheet.
LBEE5HY1MW-230 - Wi-Fi 5 + BT 5.0 Module, Type 1MW | Murata
The Murata LBEE5HY1MW-230 is a Type 1MW surface-mount wireless combo module integrating Wi-Fi 802.11a/b/g/n/ac (Wi-Fi 5) dual-band 2.4 GHz/5 GHz connectivity with Bluetooth 5.0 BR/EDR/LE on a single shielded PCB, based on the Infineon CYW43455 chipset. Per the manufacturer datasheet, the module delivers up to 433 Mbps PHY on Wi-Fi and 3 Mbps PHY on Bluetooth, with an integrated dual-band RF chain, crystal, power-management circuitry, and shielding in a compact SMD footprint suitable for space-constrained IoT and embedded designs. A Wi-Fi + Bluetooth combo module is a pre-certified subsystem that bundles the radio transceiver, baseband processor, antenna matching network, and regulatory shielding into a single reflow-solderable component. The module sits between the host application processor (which runs the network stack and BT profiles) and the wireless air interface, offloading RF complexity, FCC/ETSI/TELEC certification burden, and BOM risk. The Murata Type 1MW family specifically targets low-power IoT endpoints that need modern dual-band Wi-Fi and Bluetooth 5.0 coexistence without discrete RF design effort. Key features of the LBEE5HY1MW-230 include dual-band 2.4 GHz and 5 GHz operation with 802.11ac wave-2 (433 Mbps), Bluetooth 5.0 with LE 2M PHY and LE Coded PHY support, integrated shield and reference clock, and an SDIO 3.0 + UART host interface. The SMD package is reflow-compatible at standard 260 °C peak profile, and antenna is not included (typical for modules with host-board antenna or external antenna pigtail). Operating temperature is rated for industrial -30 °C to +85 °C environments. Architecturally, the module integrates the Infineon CYW43455 die, a 37.4 MHz reference crystal, RF matching network, transmit balun, low-noise PA chain, and DC-DC regulators on a multilayer ceramic substrate with metal shield. Wi-Fi and Bluetooth radios share an antenna diversity topology with internal coexistence arbitration, allowing simultaneous 2.4 GHz WLAN + BT operation with on-chip packet scheduling. The module presents a standard SDIO 3.0 interface to the host MCU/MPU for WLAN and a 4-wire UART (plus PCM for BT audio) for Bluetooth. Typical applications include Wi-Fi 5 + BLE smart-home gateways, industrial IoT gateways, wireless POS terminals, audio streaming products (BT classic A2DP + Wi-Fi), medical telemetry devices, and consumer electronics that need modern dual-band connectivity without in-house RF expertise. The integrated shield dramatically simplifies EMC compliance at the end-product level. When designing with the LBEE5HY1MW-230, allocate a keep-out zone under the antenna feed, provide a clean 3.3 V rail with adequate bulk decoupling, and follow Murata's reference layout for the host-board antenna or pigtail. Host-driver selection (Linux/Backport, Android HAL, or vendor-specific MCU port) is critical - confirm firmware compatibility before committing to the design. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.
LBES0ZZ2FR-580 - Wi-Fi 6 + BT 5.4 + 802.15.4 Module | Murata
The Murata LBES0ZZ2FR-580 is a Type 2FR multi-radio SMD transceiver module based on the NXP RW612 combo chipset, supporting IEEE 802.11a/b/g/n/ac/ax (Wi-Fi 6) dual-band, Bluetooth LE 5.4, IEEE 802.15.4 (Thread/Zigbee), and Matter smart-home connectivity in a single, highly integrated 140-pin surface-mount package. A Wi-Fi + Bluetooth module is a pre-certified radio subsystem that combines an RF transceiver, baseband processor, and integrated antenna or RF trace on a single PCB. These modules dramatically reduce BOM count, FCC/CE/TELEC certification cost, and PCB complexity by abstracting the radio hardware and presenting a host MCU interface. The Type 2FR sits in the module product hierarchy between simple Wi-Fi-only modules and full SoC platforms, and is widely adopted in connected smart devices, enterprise and industrial automation, smart accessories, and smart-energy endpoints. Dual-band 2.4 GHz and 5 GHz operation plus 802.15.4 makes it a true multiprotocol gateway IC for Matter, Thread, and Zigbee ecosystems. Key features include dual-band 2.4 GHz and 5 GHz Wi-Fi 6 (802.11ax) operation, Bluetooth LE 5.4 with long-range and direction-finding support, integrated 802.15.4 radio for Thread and Zigbee, an integrated high-performance Arm Cortex-M33 application MCU with advanced security (secure boot, crypto accelerators, TrustZone-M), a supply voltage range of 3.14 V to 3.46 V (typical 3.3 V), output power from 12 to 18 dBm, and receive sensitivity down to -104.7 dBm depending on modulation. The surface-mount LGA-style module ships tape-and-reel and is lead-free. The RW612 silicon inside combines a Wi-Fi 6 MAC/PHY, Bluetooth 5.4 LE radio, and 802.15.4 PHY on a single die with an internal PA, LNA, and RF front-end. Murata integrates the chipset, crystal, RF matching, and shielding into a module that is pre-certified for major regulatory domains, eliminating the customer's RF design risk and antenna tuning effort. The on-die Cortex-M33 host allows bare-metal or RTOS firmware to run directly on the module, removing the need for an external host MCU for many IoT edge applications. Typical applications include Matter-compatible smart-home hubs, Thread border routers, Wi-Fi/BLE smart appliances, industrial IoT gateways, asset-tracking sensors, and connected lighting controllers. The dual-band Wi-Fi 6 capability is particularly valuable in congested environments where 2.4 GHz-only devices suffer interference from neighboring Wi-Fi networks, microwaves, and Bluetooth peripherals. When designing with this module, follow Murata's reference layout and grounding recommendations exactly. The RF trace routing, decoupling placement, and host-interface pin mapping are pre-engineered; deviating from the reference design will degrade RF performance and may void regulatory certifications. Use the recommended host-driver SDK from NXP/Murata to leverage the integrated MCU and radio coexistence features.
LBEU5ZZ1WL-633EVB - LoRaWAN GNSS BLE Wi-Fi Eval Board | Murata
The Murata LBEU5ZZ1WL-633EVB is an evaluation board for the Type 1WL (LBEU5ZZ1WL-633) multi-technology fused LoRaWAN geolocation module, which combines Semtech LR1110 LoRa/Wi-Fi/GNSS scanning, a STMicroelectronics STM32WB55VGY6 wireless MCU, and an Airoha MT3333AV high-performance GNSS receiver in one platform for developing low-cost IoT tracking devices. An LPWAN geolocation module is a type of wireless connectivity module that fuses long-range low-power radio (LoRaWAN) with multiple positioning technologies (satellite GNSS, Wi-Fi access-point scanning, and GNSS scanning). Within the system hierarchy, it sits above individual transceivers and below complete end products, providing a pre-certified radio subsystem for asset tracking, telemetry, and industrial IoT nodes. Key features include ultra-low power design: the internal MCU draws only 4.7 uA typical in stop2 mode with RTC running while the LR1110 and MT3333 are off, per the Type 1WL datasheet (Rev. D, VDD = 3.3 V, 25 C). Wireless coverage spans LoRa sub-GHz, Wi-Fi 802.11b/g/n at 2.4 GHz, Bluetooth v5.2, and GNSS including GPS and BeiDou. The STM32WB55 provides an ARM Cortex-M4 core with 256 KB RAM and 1 MB Flash, plus a USB 2.0 full-speed interface that is USB-IF certified. Technically, the module fuses three positioning engines: LR1110 Wi-Fi and GNSS scanning delivers indoor/outdoor fixes without acquiring full satellite signals, the MT3333AV provides standalone high-performance GNSS, and LoRaWAN uplink transports position and telemetry to network servers such as those used by Abeeway-based tracking solutions. The evaluation board exposes the module interfaces, antenna connections (antenna not included on the module), and USB connectivity for rapid prototyping. Typical applications include battery-powered asset trackers for logistics, industrial equipment monitoring, indoor/outdoor personnel and livestock tracking, and smart-city IoT sensors that need multi-year battery life. The 4.7 uA sleep current enables designs that run for years on a primary lithium cell. Design consideration: budget antenna selection and RF layout early, since the module ships without an antenna and GNSS/Wi-Fi/LoRa performance depends heavily on placement and ground-plane design. This page synthesizes distributor availability, datasheet-derived specifications, and practical design notes not found in the manufacturer datasheet alone.
LBUA5QJ2AB-828 - UWB + BLE 5.2 Combo Module | Murata
The Murata LBUA5QJ2AB-828 is a hostless UWB (ultra-wideband) + Bluetooth 5.2 Low Energy combo transceiver module supporting UWB operation across the 6250 MHz to 8250 MHz range (IEEE 802.15.4z channels, Band 5 and Band 9) in a compact 10.5 x 8.3 mm surface-mount LGA package with 97 pins. Antenna is not included, allowing design flexibility with external UWB and BLE antennas. An ultra-wideband module is a short-range, high-precision radio module that transmits nanosecond-scale pulses across very wide bandwidths, enabling centimeter-level distance measurement (secure ranging) that narrowband radios such as Bluetooth or Wi-Fi cannot achieve. UWB modules sit within the broader RF transceiver module hierarchy, and combo modules like this one pair UWB ranging with a conventional low-power radio for wake-up, control, and data functions. Key features include the Qorvo QM33120W UWB chipset paired with an integrated Nordic Semiconductor nRF52840 that provides Bluetooth 5.2 LE, firmware update, and wake-up control. The module is FCC/IC/TELEC reference certified, dramatically reducing end-product regulatory effort. An integrated 3-axis accelerometer supports battery-saving duty cycling, and reference clocks for both the UWB chip and MCU are embedded on the module, simplifying BOM and calibration. Architecturally, the hostless design means the nRF52840 manages the UWB radio autonomously, allowing UWB ranging sessions to execute without waking the host processor. The nRF52840 provides 1 MB flash and 256 kB RAM for embedded application code, with host interfaces including I2C, SPI, UART, and USB. Typical applications include secure car-access key fobs and automotive door-zone detection, indoor asset tracking and real-time location systems (RTLS), and smart-door locks and access-control systems where UWB secure ranging prevents relay attacks. Design consideration: since the antenna is not integrated, place the module near the antenna connectors with controlled-impedance RF traces and follow Murata's reference layout for the 6.5 GHz and 8 GHz bands to pass certification. This page synthesizes distributor pricing, cross-reference findings, and design guidance not consolidated in the manufacturer datasheet.
LBWA0ZZ2HK - Sub-1GHz Wi-Fi HaLow 11ah Module | Murata | IoT
The Murata LBWA0ZZ2HK (Type 2HK) is a long-range Sub-1GHz Wi-Fi HaLow system-on-module based on the NEWRACOM NRC7394 chipset, supporting IEEE 802.11ah SISO operation in the 902 MHz to 928 MHz band with a communication range of up to 2 km, packaged as a compact surface-mount connectivity module. A Wi-Fi HaLow module is a wireless connectivity subsystem that implements the IEEE 802.11ah standard, which operates in sub-1 GHz license-exempt spectrum rather than the crowded 2.4 GHz and 5 GHz bands used by conventional Wi-Fi. Within the network hierarchy, it sits between a host microcontroller or application processor and the RF front end and antenna, offloading the full MAC and PHY of the 802.11ah S1G standard. Sub-1 GHz radios trade raw throughput for dramatically longer range, better penetration through walls and foliage, and lower power consumption, making HaLow the Wi-Fi-family choice for IoT mesh and star networks where 2.4 GHz Wi-Fi, BLE, or 802.15.4 range is insufficient. Key features of the LBWA0ZZ2HK include its NRC7394 chipset base supporting 802.11ah SISO, coverage of the 902-928 MHz US band, ultra-low power consumption with advanced sleep features for battery operation, an embedded RTOS with IP-native application support, and Murata-grade module integration that simplifies regulatory certification (FCC ID VPYLBWA0ZZ2HK). Technically, the module integrates the NRC7394 SoC, crystal, RF matching network, and flash into a single shielded land-grid package. The 2 km link range is achieved by combining narrowband sub-1 GHz propagation with the robust modulation and coding schemes of 802.11ah. The embedded RTOS and TCP/IP stack allow the host processor to use simple AT-style or socket interfaces instead of implementing a Wi-Fi stack. Typical applications include smart utility metering, industrial sensor networks, smart-city infrastructure, agricultural monitoring, and battery-powered security and access-control devices - all scenarios where devices are spread over campus-scale distances and must run for years on batteries. Design-wise, provide a clean 3.3 V supply with local decoupling, route the antenna per Murata's FCC integration instructions, and account for HaLow transmit bursts in battery budget calculations rather than using average current alone. This page synthesizes verified manufacturer and distributor data, drop-in alternatives, engineering design notes, and FAQ content not found together in the product brief.
LBWA0ZZ2HL - Sub-1GHz Wi-Fi HaLow 802.11ah Module | Murata
The Murata LBWA0ZZ2HL (Type 2HL) is a long-range Sub-1GHz Wi-Fi HaLow system-on-module based on the NEWRACOM NRC7394 chipset, supporting IEEE 802.11ah SISO operation from 750 MHz to 950 MHz with data rates up to 15 Mbps, output power up to 17 dBm, and line-of-sight communication range up to 1 km from a 2.7 V to 3.6 V supply. A Wi-Fi HaLow module is a wireless connectivity module that implements the IEEE 802.11ah Sub-1 GHz (S1G) amendment of the Wi-Fi standard. Unlike conventional 2.4 GHz and 5 GHz Wi-Fi, HaLow trades peak bandwidth for substantially greater range, better wall-penetration, and lower power consumption, making it a member of the low-power wide-area (LPWAN) connectivity family alongside LoRa and NB-IoT, while retaining native IP networking and Wi-Fi security. Key features of the LBWA0ZZ2HL include operation across key regional Sub-1 GHz bands (the HL variant covers 750-950 MHz bands for regions such as Europe, Japan and others, while the companion HK variant targets 902-928 MHz), ultra-low power consumption for battery-powered IoT endpoints, and data rates up to 15 Mbps - far higher than typical LPWAN technologies. The integrated NRC7394 SoC handles MAC, baseband and RF in a single chipset, simplifying host integration over SDIO/SPI interfaces. Technically, the module implements 802.11ah SISO with standard Wi-Fi security, allowing direct IP connectivity to HaLow access points. Murata, as a leading module manufacturer, provides certification-ready design that reduces end-product regulatory burden across key regions. According to Murata product literature, the Type 2HL is designed specifically for the connectivity needs of Internet of Things (IoT) devices. Typical applications include smart utility metering, industrial sensors, building automation, smart city infrastructure, and agricultural monitoring - all scenarios requiring multi-hundred-meter to kilometer-scale links with years of battery life. Designers should verify regional RF regulatory certification (the HL and HK variants cover different frequency bands) and confirm antenna matching and supply filtering per the manufacturer datasheet. This page synthesizes verified distributor and manufacturer data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
LE910C1-EU - LTE Cat.1 10/5 Mbps Module | Telit Cinterion
The Telit Cinterion LE910C1-EU is an LTE Cat.1 cellular IoT transceiver module delivering 10 Mbps downlink and 5 Mbps uplink data rates, compliant with 3GPP Release 10, housed in a compact LGA (land grid array) surface-mount form factor with an optional quad-constellation GNSS receiver supporting GPS, GLONASS, Galileo, BeiDou, and QZSS. An LTE Cat.1 module is a category of cellular RF transceiver module that provides full-duplex LTE connectivity at modest data rates, sitting within the broader hierarchy of cellular modems: M2M module -> LTE transceiver module -> wireless communication IC. Cat.1 is widely adopted as the migration path from 2G/3G for machine-to-machine devices because it uses the existing LTE network infrastructure without the complexity of Cat-M1 or NB-IoT, while still supporting voice and data. Key features of the LE910C1-EU include the 10/5 Mbps throughput profile, 3GPP Rel 10 compliance with Rel 12-ready MTC platform features, integrated TCP/IP and UDP/IP protocol stacks, and peripheral connectivity via USB 2.0 HS, UART, and user-definable GPIOs. These characteristics make it well suited to devices that need dependable, always-on wide-area connectivity without a host-side network stack. The module is part of Telit's flagship xE910 family, whose design-once, use-anywhere philosophy allows LE910C1 variants to serve as pin-to-pin compatible replacements within the same LGA footprint for devices based on earlier 2G, 3G, and LTE family members. The ThreadX RTOS-based firmware platform simplifies application integration, and the LE910Cx family is also offered in Linux-based SKUs for more demanding gateway applications. Typical applications include smart metering, asset tracking and fleet telematics, industrial gateways and routers, security and alarm panels, and connected point-of-sale terminals, where European-band LTE coverage and low-power, long-lifecycle operation are priorities. When designing with the LE910C1-EU, budget for a proper RF layout: the antenna is not included, so PCB antenna feed matching, keep-out zones, and supply decoupling follow the Telit LE910C1 Series hardware user's manual guidance for the LGA footprint. This page synthesizes distributor pricing and availability, drop-in alternatives within the xE910 family, and practical design guidance not consolidated in the manufacturer datasheet.
LM048 - Class 1 Bluetooth RS232 Serial Adapter 100m | LM Technologies
The LM Technologies LM048 is a Class 1 Bluetooth® Serial Adapter (RS232) that provides a secure and reliable wireless link replacing legacy RS232 cables between DTE master devices and DCE peripherals such as printers, data loggers, and digital signalling equipment. Housed in a compact plastic enclosure and billed by the manufacturer as the world's smallest Bluetooth® serial adapter, the LM048 delivers up to 100 m line-of-sight range using an onboard antenna while operating from either RS232 Pin 9 (4 V to 13 V) or a Mini-USB supply. A Bluetooth® serial adapter is a self-contained cable-replacement module that bridges a wired RS232 UART interface to a Bluetooth SPP/Serial Port Profile link. Inside the adapter, a Bluetooth baseband IC handles the v2.0/v2.1 + EDR radio (Class 1, up to +18 dBm Tx) and the SPP stack; an RS232 transceiver converts UART logic levels to the ±5 V to ±15 V signaling required by RS232 peripherals. Pairing is transparent to the host: RS232 control lines DTR, DSR, RTS, and CTS are replicated end-to-end over the wireless link via the LM048's patented firmware, allowing legacy Windows/Linux serial applications to operate without modification. The headline specifications include Bluetooth® v2.0/v2.1 with EDR (3 Mbps nominal), Class 1 output power (approximately +18 dBm Tx), -86 dBm Rx sensitivity, and adaptive frequency hopping across the 2.402 GHz to 2.480 GHz ISM band. The adapter accepts RS232-standard baud rates (typical coverage 1.2 kbps up to 460 kbps per public listings) and operates from -20 °C to +75 °C. Power can be sourced from RS232 Pin 9 (4 V to 13 V) or from a Mini-USB port, and the plastic housing exposes a slide switch plus LEDs for status and pairing feedback. A pair of LM048 adapters using their unique hardware and firmware combination can act as a transparent serial cable replacement, removing the need for driver changes on the host. The unit carries relevant Bluetooth SIG certifications and CE/FCC compliance marks as listed in the manufacturer datasheet. Typical applications include industrial RS232 cable replacement, factory-floor data loggers, point-of-sale printers, bar-code scanners, and remote telemetry units. Designers typically route 5 V to 9 V to Pin 9 and connect TX/RX directly to the host UART bridge. When designing a drop-in cable-replacement node, choose between powering from the RS232 Pin 9 line or USB Mini; a pair of LM048 units gives a true transparent null-modem replacement. Note that throughput tops out near the 460 kbps baud ceiling and the radio is limited to Bluetooth v2.0/v2.1 + EDR, not BLE 5.x. This page synthesizes distributor pricing for the LM048, same-brand LM Technologies variants (LM048 v2, LM058, LM400, LM072) and practical drop-in guidance not collected in the manufacturer datasheet.
LM068 - Bluetooth 5.0 Dual Mode RS232 Serial Adapter | LM Technologies
The LM Technologies LM068 is a Bluetooth 5.0 Dual Mode RS232 Serial Adapter packaged as a standalone module with an embedded Bluetooth 5.0 stack. It operates with a supply voltage of 4V to 12V, supports data rates up to 3 Mbps, and is designed to replace wired RS232 cables between a master (DTE) device and slave (DCE) devices such as printers, data loggers, and digital signalling instruments. The adapter runs on an internal microcontroller paired with an 8 Mbit flash memory for application storage, enabling firmware configurability through the LM149v2 host utility. A Bluetooth serial adapter is a self-contained wireless bridge that replaces a legacy UART/RS232 cable with a Bluetooth link. In the broader taxonomy it sits under wireless modules -> RF modules -> RF transceivers -> communication ICs -> semiconductors. The adapter exposes a standard DB9 RS232 connector on the DTE side and converts the UART traffic to a Bluetooth 5.0 link on the slave side. Dual Mode means it can connect to both Bluetooth Classic (BR/EDR) and Bluetooth Low Energy (BLE) hosts, providing flexibility for legacy SPP-style serial replacement as well as modern low-power BLE devices. Key features of the LM068 include Bluetooth 5.0 dual mode support (Classic + BLE), a configurable firmware via the LM149v2 utility, configurable baud rate, data bits, parity and flow control, support for SPP (Serial Port Profile) over Classic, and a small physical footprint of 46.3 mm x 34 mm x 16 mm. The power input is versatile: USB-Mini, DB9, or an external AC adaptor. Settings persist across power cycles, eliminating the need to reconfigure on every boot. The adapter also supports auto-connect and discoverable/non-discoverable modes, simplifying integration in industrial machines where operators frequently reconnect cables between cycles. The internal architecture pairs a microcontroller with a Bluetooth 5.0 module, with the MCU handling profile bridging and configuration. Because the stack is embedded, the host CPU never sees raw radio activity; it only exchanges UART bytes, simplifying software integration on systems that cannot host a Bluetooth stack (older PLCs, microcontrollers without BLE, lab instruments). Typical applications include replacing RS232 cables in industrial machinery, wireless connection to data loggers and printers, point-to-point serial tunneling for embedded devices, and office equipment that needs occasional wireless configuration access without permanent cabling. The wide 4-12V input range lets it draw power from the host's existing DC rail or an AC wall adaptor. When selecting the LM068, ensure that the target host device has an RS232 DB9 port, or plan for a USB-to-RS232 converter. The adapter cannot exceed approximately 3 Mbps aggregate throughput, which is faster than classic RS232 (115.2 kbps typical) but considerably slower than modern Wi-Fi or Ethernet alternatives. Pick this part when you need a deterministic cable replacement with minimal configuration, not for high-bandwidth streaming. This page synthesizes distributor availability, configuration guidance and drop-in alternative notes that complement the manufacturer's datasheet. Compared to bare Bluetooth modules the LM068 is a finished adapter with connectors and firmware, so its alternatives must also be finished serial adapters in the same form factor, not bare radio modules.
LM509 - Bluetooth 5.4 Dual Mode Class 1 USB Adapter | LM Technologies
The LM Technologies LM509 is a Bluetooth 5.4 dual mode Class 1 USB adapter that provides plug-and-play wireless connectivity for host computers. Housed in an ultra-small form-factor USB dongle, it supports Bluetooth 2.x, 4.x, and 5.x profiles, enabling communication with iOS, Android, printers, keyboards, speakers, and headphones using both Bluetooth Classic (BR/EDR) and Bluetooth Low Energy (LE) radio paths. According to the LM Technologies LM509 datasheet, the adapter is compatible with Linux as well as Windows 10 through Windows 11 host platforms. Background knowledge: Bluetooth dual mode adapters are external peripherals that aggregate a Bluetooth Classic radio (for legacy audio, HID, and SPP profiles) and a Bluetooth Low Energy radio (for modern IoT, beacon, and low-power sensor profiles) onto a single USB endpoint. They are classified as Class 1 when their transmit output power reaches up to +20 dBm and supports an indoor range of roughly 30 meters, which extends coverage well beyond the Class 2 limit (~10 m) used in most laptops. Bluetooth 5.4 itself is a core specification released by the Bluetooth SIG that adds PAwR (Periodic Advertising with Responses), LE-Game-Controller profile support, and encrypted advertisement data, in addition to the 2x throughput and 4x range improvements of Bluetooth 5.0. Key specifications of the LM509 include its dual-mode Bluetooth 5.4 radio, Class 1 transmit power, USB Type-A plug-and-play interface, and OS coverage from Windows 10/11 to mainline Linux kernels. The adapter exposes dual radio paths (BR/EDR + LE) so a host can pair both legacy audio peripherals and modern BLE sensors simultaneously. Bluetooth 5.4 features supported include advertising extensions, periodic advertising with responses, and LE audio metadata. The product is supplied as a finished, end-user-ready module, not a bare silicon IC. Its architecture centers on a Bluetooth 5.4 SoC paired with a Class 1 RF front-end, USB 2.0 device controller, and integrated PCB antenna or external RF chain depending on the SKU variant. The completed enclosure is tested by the manufacturer for EMC and RF conformance, which removes RF tuning work from the integrator. Typical use cases include adding wireless audio and HID connectivity to industrial PCs, providing BLE data uplink for IoT gateways, and acting as a development dongle during Bluetooth firmware bring-up. For successful deployment, verify that the host OS supplies USB HID/Bluetooth enumeration support and that Class 1 radio emissions comply with the regional ETSI/FCC/IC radio regulations at the installation site. The USB bus supplies the device with 5 V at roughly 100 mA, so no external power is required.