AD542SH - Low-Noise BiFET Op Amp, ±18V, TO-99
부품 번호: AD542SH ✓ 활성AD542SH 개요
A BiFET operational amplifier is a voltage-feedback amplifier whose field-effect-transistor input stage provides very low input bias current. This input characteristic places the AD542SH in the broader hierarchy of FET-input operational amplifiers, analog amplifiers, signal-conditioning ICs, and power-management-supporting semiconductor devices. Low input current is especially useful when the amplifier must interface with high-impedance sensors, transducers, photodetectors, or precision measurement networks without loading the source.
Key characteristics include a maximum input offset voltage of 1 mV, input offset drift of 15 µV/°C, a quiescent current of 1.5 mA, open-loop gain of 110 dB, and a listed common-mode rejection value of 80 dB. Its 13 V/µs slew rate supports comparatively fast large-signal transitions, while the 1 MHz gain-bandwidth product is suitable for precision gain, buffering, and general-purpose analog amplification. The AD542SH also provides overvoltage protection and can drive capacitive loads according to the manufacturer documentation.
The AD542SH belongs to the AD542, AD544, and AD547 precision BiFET family, which uses monolithic BiFET construction and laser-trimming technology. This combination targets applications in which conventional bipolar input stages would draw excessive bias current or introduce unacceptable source loading. The low-bias architecture is especially valuable in instrumentation, photodetector interfaces, and high-impedance sensor amplifiers, while the laser-trimmed offset characteristics support stable DC operation.
Typical uses include low-level sensor conditioning, photodiode and phototransistor amplification, buffered measurement inputs, precision current-to-voltage conversion, and gain stages in laboratory or industrial instrumentation. The hermetic TO-99 package can also suit equipment requiring a traditional metal-can mechanical format. Because the amplifier is a voltage-feedback device, feedback-network design, source impedance, load capacitance, and common-mode operating range remain central to stable operation.
When laying out a circuit using the AD542SH, keep feedback resistors close to the device and minimize parasitic capacitance on the output and inverting-input nodes. Check bias-current cancellation for high source impedances, because although the maximum input bias current is only 25 pA, even picoamp-level current can create meaningful offset across megaohm-class resistances. Confirm output swing, input common-mode range, and capacitive-load stability against the manufacturer operating table.
This page combines the AD542SH electrical characteristics, package details, application guidance, design notes, and family comparisons to support engineering selection and PCB implementation. It also organizes drop-in family options and clearly identifies which replacement questions require additional qualification before schematic or layout changes are approved.
드롭인 대체품: AD542SH — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: AD542SH (동일 폼 팩터 및 풋프린트) — 차이점: Maximum Input Bias Current, Package, Product Type.
AD544SH
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →AD547SH
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD544JH
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD547JH
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD542JH
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD542SH 최대 정격 & 전기적 특성
| Product Type | Single precision BiFET-input operational amplifier |
| Number of Channels | 1 channel |
| Input Stage | BiFET field-effect-transistor input |
| Maximum Input Bias Current | 25 pA |
| Maximum Input Offset Voltage | 1 mV |
| Input Offset Voltage Drift | 15 µV/°C |
| Supply Voltage Range | ±18 V |
| 대기 전류 | 1.5 mA |
| Slew Rate | 13 V/µs |
| Gain-Bandwidth Product | 1 MHz |
| Open-Loop Gain | 110 dB |
| Common-Mode Rejection | 80 dB |
| Noise | 2 V p-p |
| Input Protection | Overvoltage protection |
| Capacitive-Load Capability | Capacitive-load drive supported |
| 패키지 | TO-99, 8 pins |
| 실장 유형 | Through-hole metal-can package |
AD542SH 핀 구성
| 핀 1 | NC — Not connected |
| 핀 2 | IN- — Inverting input |
| 핀 3 | IN+ — Non-inverting input |
| 핀 4 | V- — Negative supply voltage |
| 핀 5 | OFFSET NULL — Offset-voltage null adjustment |
| 핀 6 | OUT — Amplifier output |
| 핀 7 | V+ — Positive supply voltage |
| 핀 8 | NC — Not connected |
일반적인 애플리케이션
AD542SH 적합 용도: 6 애플리케이션s: High-Impedance Sensor Conditioning, Photodetector Signal Amplification, Precision Current-to-Voltage Conversion, Instrumentation Buffering, Industrial Control Signal Interface, Precision Audio and Analog Measurement.
High-Impedance Sensor Conditioning
The AD542SH is appropriate for front ends connected to photodiodes, high-resistance transducers, capacitive sensors, and other sources whose output impedance is high. Its maximum input bias current of 25 pA limits the error voltage caused by bias current flowing through the source impedance. The amplifier can therefore preserve a weak sensor signal before it reaches a subsequent ADC or measurement channel. Because source resistance also amplifies thermal and leakage effects, the design should include guarding, clean PCB leakage control, and resistor matching for bias-current cancellation. The 1 MHz gain-bandwidth product is sufficient for moderate-bandwidth instrumentation, while the 13 V/µs slew rate supports faster settling when the closed-loop gain and load permit it.
추천
Photodetector Signal Amplification
A photodiode or phototransistor can be connected to an AD542SH configured as a transimpedance or voltage-gain stage when the source generates currents too small for a conventional bipolar-input amplifier to handle efficiently. The AD542SH's 25 pA maximum bias current is particularly useful because it produces less unwanted photocurrent-equivalent error at the detector node. Its 110 dB open-loop gain supports accurate closed-loop gain when configured with practical feedback resistors. The 1 MHz gain-bandwidth product limits the bandwidth available after noise gain is accounted for, and the 13 V/µs slew rate must also be checked against the detector capacitance and selected feedback network. PCB layout should minimize guard-ring leakage and keep the detector input path away from high-impedance digital return currents.
추천
Precision Current-to-Voltage Conversion
The AD542SH can implement a precision transimpedance amplifier for current-output sensors, optical receivers, or laboratory measurement circuits. Its low input bias current reduces the DC offset contribution associated with the input stage, while the 1 mV maximum input offset voltage supports accurate conversion at reasonable signal gains. The 1 MHz gain-bandwidth product defines the usable signal bandwidth after the noise gain and feedback resistance are considered. Feedback-resistor parasitics and input capacitance can alter stability, so component selection and compensation should be evaluated using the manufacturer's guidance. The low 1.5 mA quiescent current is also advantageous in portable instrumentation, although the total supply current will rise as the output drives load current.
추천
Instrumentation Buffering
The AD542SH can buffer an instrumentation or laboratory sensor before it reaches a downstream converter, multiplexer, or data-acquisition system. Its 25 pA maximum input bias current reduces loading of a high-output-resistance source, while the 110 dB open-loop gain helps minimize closed-loop gain error. A 1 MHz gain-bandwidth product is appropriate for many general-purpose measurement channels, but applications requiring substantially more bandwidth should re-evaluate the family choice. The 13 V/µs slew rate helps produce clean responses to step changes and supports capacitive loads within the documented operating conditions. Layout should keep the input and feedback nodes short, use a ground plane without splits beneath the amplifier, and provide local supply bypassing to prevent measurement noise from coupling into the signal path.
추천
Industrial Control Signal Interface
The AD542SH is suitable for low-level control and feedback signals in industrial equipment when the interface source has high impedance and low current capability. The amplifier can condition sensor outputs or drive downstream control inputs while drawing only about 1.5 mA quiescent current. Its ±18 V rating supports circuits using positive and negative supply rails, but the actual operating limits must be checked against the selected grade and total supply voltage. The 1 mV maximum offset and 15 µV/°C drift establish important accuracy boundaries for slow-changing control signals. Industrial implementations should also include input protection, verified supply bypassing, and adequate separation from switching nodes. The TO-99 package provides a through-hole mechanical option for systems designed around metal-can operational amplifiers.
추천
Precision Audio and Analog Measurement
The AD542SH can be used in low-level audio, laboratory, and analog measurement stages where input-current loading must remain small. The BiFET input stage, with bias current no greater than 25 pA, avoids the larger loading associated with conventional bipolar transistor inputs. The 13 V/µs slew rate can reproduce moderate-level audio transients, although the 1 MHz gain-bandwidth product makes the device more appropriate for instrumentation than wideband audio output stages. Its 110 dB open-loop gain is useful for accurate fixed-gain sections, and the listed 80 dB common-mode rejection can help reject common-mode interference when supply noise is properly bypassed. Signal-ground topology should be designed to avoid ground loops, and the metal-can package requires careful mechanical support and lead strain control.
추천
추천 제품 요약
엔지니어링 참조 데이터: AD542SH — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AD544SH | AD547SH | AD544JH | AD547JH | AD542JH |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TO-99, 8 pins | TO-99, 8 pins | TO-99, 8 pins | TO-99, 8 pins | TO-99, 8 pins | TO-99, 8 pins |
| Product Type | Precision BiFET-input operational amplifier | Precision BiFET-input operational amplifier | Precision BiFET-input operational amplifier | Precision BiFET-input operational amplifier | Precision BiFET-input operational amplifier | Precision BiFET-input operational amplifier |
주요 차별점
- Very low input bias current for precision signal conditioning (vs AD542JH)
- Defined dynamic performance for measurement circuits (vs AD544SH)
- TO-99 mechanical compatibility within the precision BiFET family (vs AD547SH)
설계 노트
Route the non-inverting input, inverting input, and feedback components as short and compact as practical. High-impedance bias current is useful only if the board does not introduce comparable leakage through contaminated connectors, flux residue, or humid board surfaces. Use a guarded or solder-masked input node where appropriate, avoid copper underneath the sensitive input path, and keep the inverting node away from switching-power and digital return paths. The 25 pA maximum bias-current specification defines the amplifier itself, not the leakage budget of the complete PCB assembly.
Calculate amplifier dissipation from both supply rails rather than treating ±18 V as a single supply condition. Estimated: with a 1.5 mA quiescent current, 15 V on each rail, and an output near ground, quiescent dissipation is approximately 45 mW before output-current loading. Actual dissipation rises when the output conducts current and depends on the output voltage and load. Verify the selected grade's maximum supply voltage, total supply voltage, output swing, and power limitations before applying ±18 V.
Do not assume that a common TO-99 outline guarantees identical pin assignments. Confirm the AD542SH pin-description table, including offset-null and no-connect positions, before laying out the PCB. Also avoid using the offset-null terminals for permanent adjustment unless the circuit requires calibration. When replacing AD542SH with an AD544 or AD547 family device, check the exact offset-voltage limit, offset drift, slew rate, gain-bandwidth product, input bias current, temperature grade, and supply requirements; a shared 8-pin package alone does not establish functional equivalence.
Account for the 1 MHz gain-bandwidth product when selecting feedback values and expected closed-loop bandwidth. At a noise gain of 10, the approximate signal bandwidth available from the gain-bandwidth limit is only 100 kHz before additional poles and stability effects are considered. The 13 V/µs slew rate also imposes a large-signal limit, and the output must remain within its specified swing. For capacitive loads, use a series isolation resistor or another compensation method when necessary to prevent ringing or instability.
규정 준수 정보
The AD542SH is a precision analog operational amplifier rather than an automotive-qualified device. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the referenced product information.