ATMEGA16-16MC - 8-bit AVR MCU 16MHz 16KB Flash 44-VQFN | Microchip
부품 번호: ATMEGA16-16MC ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.2 | $3.20 |
| 10 | $2.88 | $28.80 |
| 100 | $2.46 | $246.00 |
| 500 | $2.15 | $1,075.00 |
| 1,000 | $1.9 | $1,900.00 |
ATMEGA16-16MC 개요
An AVR ATmega microcontroller is an 8-bit reduced-instruction-set (RISC) MCU that executes most of its 131 powerful instructions in a single clock cycle. In the broader system hierarchy, an MCU combines a CPU core, program memory (Flash), data memory (SRAM and EEPROM), and peripherals such as timers, USART, SPI, and ADC into a single integrated circuit, forming the backbone of embedded control systems.
Key features include the Advanced RISC architecture with 32 general-purpose working registers, an 8-channel 10-bit analog-to-digital converter, and a JTAG interface for on-chip debugging and boundary-scan. The self-programming Flash enables bootloader firmware updates in the field, while the hardware USART, SPI, and two-wire interface (I2C/TWI) cover most embedded communication requirements.
Architecturally, the ATmega16 uses a Harvard bus structure that separates instruction and data paths, allowing one instruction to execute while the next is fetched. Six of the eight 8-bit timers/PWM channels (two 8-bit and one 16-bit timer with PWM outputs) support motor control, LED dimming, and precise waveform generation with minimal CPU overhead.
Typical applications include industrial automation nodes, building control and HVAC boards, hobby and educational embedded platforms, and consumer appliance controllers, where the combination of 10-bit ADC, hardware serial ports, and 5V operation simplifies system design.
For design, note that the -16 speed grade requires a supply of 4.5V to 5.5V; decouple VCC/AVCC with 100 nF ceramics placed directly at the package pins, and route the JTAG header for in-system debugging.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: ATMEGA16-16MC — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATMEGA16-16MC (동일 폼 팩터 및 풋프린트) — 차이점: EEPROM, Package, SRAM, Supply Voltage, ADC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATMEGA16-16MU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATMEGA16A-MU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATMEGA32A-MU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATMEGA324PA-MU
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.05 / 개
데이터시트 보기 →ATMEGA8535-16MU
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.52 / 개
데이터시트 보기 →ATMEGA16-16MC 최대 정격 & 전기적 특성
| Core Architecture | 8-bit AVR RISC |
| 최대 클록 주파수 | 16 MHz |
| Throughput | up to 16 MIPS at 16 MHz |
| Flash Program Memory | 16 KB (8K x 16), self-programming |
| SRAM | 1 KB |
| EEPROM | 512 Byte |
| Instructions | 131 instructions, most single-cycle |
| ADC | 8-channel 10-bit |
| Timers/Counters | Two 8-bit and one 16-bit with PWM |
| Communication Interfaces | USART, SPI, TWI (I2C) |
| Debug Interface | JTAG for on-chip debug and boundary scan |
| 공급 전압 | 4.5 V to 5.5 V (-16 speed grade) |
| 패키지 | 44-VQFN (7x7 mm), MLF-44 |
| 실장 유형 | Surface Mount |
ATMEGA16-16MC 44-vqfn (7x7 mm), mlf-44 핀 구성 가이드
ATMEGA16-16MC(44-vqfn (7x7 mm), mlf-44 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATMEGA16-16MC.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATMEGA16-16MC 적합 용도: 6 애플리케이션s: Industrial Automation Control Nodes, Appliance and HVAC Control Boards, Educational and Prototyping Platforms, Building Control and Sensor Networks, Motor and PWM Actuator Control, Legacy System Maintenance and BOM Continuity.
Industrial Automation Control Nodes
The ATMEGA16-16MC fits industrial automation nodes that need deterministic 8-bit control with robust 5V I/O. Its 16 MIPS throughput at 16 MHz and 131-instruction single-cycle RISC core execute PID control loops and Modbus-style polling without external glue logic, while the 8-channel 10-bit ADC reads potentiometers, current shunts, and temperature sensors directly. The hardware USART handles RS-485 fieldbus traffic, and SPI connects isolated I/O expanders. Typical deployment is between a 5V regulated rail and optocoupled field wiring, where the 44-VQFN 7x7 mm package saves board area versus DIP alternatives. JTAG on-chip debug shortens commissioning time on production fixtures.
추천
Appliance and HVAC Control Boards
Consumer appliance and HVAC controller boards benefit from the ATMEGA16-16MC's combination of 512 B EEPROM for storing user settings and calibration data, a 10-bit ADC for NTC temperature sensing, and PWM timer outputs for triac or fan control. The 5V operating range tolerates noisy appliance power rails, and the self-programming 16 KB Flash supports field firmware updates via bootloader over the hardware USART. At a typical 8-16 MHz clock, the MCU handles button scanning, display multiplexing, and sensor averaging concurrently. The MLF-44 package's exposed pad improves thermal and ground integrity in sealed enclosures with limited airflow.
추천
Educational and Prototyping Platforms
Universities and maker platforms use the ATmega16 family as a teaching vehicle because its 131-instruction AVR RISC core, 32 registers, and peripheral set map cleanly onto embedded-systems curricula. The ATMEGA16-16MC's JTAG interface allows full on-chip debugging - breakpoints, single-stepping, and register inspection - which is superior to print-based debugging in lab settings. Its 8-channel 10-bit ADC supports lab exercises in signal acquisition, and the hardware USART connects to PC terminals for bootloader exercises. Breadboard-friendly TQFP-44 adapter boards accept the same code base as the VQFN-16MC version, simplifying the transition from prototype to production package.
추천
Building Control and Sensor Networks
Building automation sensor nodes use the ATMEGA16-16MC's TWI (I2C) master/slave interface to poll humidity, light, and occupancy sensors, while the 10-bit ADC digitizes analog occupancy and temperature channels. The 16 KB Flash accommodates a lightweight protocol stack and application logic, and 1 KB SRAM buffers network packets. On battery-backed nodes, designers typically choose the ATMEGA16-8 speed grade variant for 2.7V operation; the -16MC part suits mains-powered nodes where the 4.5-5.5V rail and 16 MHz speed give headroom for fast response to occupancy events. The USART links the node to RS-485 trunk cabling.
추천
Motor and PWM Actuator Control
The ATMEGA16-16MC generates up to six PWM channels from its two 8-bit timers and one 16-bit timer, making it suitable for DC motor speed control, servo positioning, and LED dimming actuator boards. At 16 MHz, 8-bit PWM resolution yields roughly 62.5 kHz carrier frequencies suitable for quiet motor drive, while the 16-bit timer supports low-frequency servo updates with precise 1 us-class resolution. The 10-bit ADC closes the loop by sampling current-sense shunts or back-EMF, and the JTAG debug port helps tune control loop constants on live hardware. The exposed-pad VQFN-44 package aids ground return for switching loads.
추천
Legacy System Maintenance and BOM Continuity
Production lines with existing ATmega16-based designs use the ATMEGA16-16MC to keep PCBs in build without redesign. Because the -16MC shares the MLF-44/VQFN-44 footprint with the ATMEGA16-16MU and the pin-compatible ATMEGA16A-MU successor, boards can be second-sourced or die-upgraded with zero layout change, and firmware compiled for the original ATmega16 runs unchanged on the A-variant. Engineering teams should verify fuse settings and ADC calibration on first articles, since the enhanced die improves analog linearity. Maintaining JTAG programming fixtures unchanged also preserves production test investment for legacy assemblies.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATMEGA16-16MC — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATMEGA16-16MU | ATMEGA16A-MU | ATMEGA32A-MU | ATMEGA324PA-MU | ATMEGA8535-16MU |
|---|---|---|---|---|---|---|
| Package | 44-VQFN (MLF-44, 7x7 mm) | 44-VQFN (MLF-44) - same | 44-VQFN (MLF-44) - same | 44-VQFN (MLF-44) - same | 44-VQFN (MLF-44) - same | 44-VQFN (MLF-44) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Program Memory | 16 KB | 16 KB | 16 KB | 32 KB | 32 KB | 8 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 2 KB | 2 KB | 512 B |
| EEPROM | 512 B | 512 B | 512 B | 1 KB | 1 KB | 512 B |
| Maximum Clock / Throughput | 16 MHz / 16 MIPS | 16 MHz / 16 MIPS | 16 MHz / 16 MIPS | 16 MHz / 16 MIPS | 20 MHz / 20 MIPS | 16 MHz / 16 MIPS |
| ADC | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit |
| Debug Interface | JTAG on-chip debug | JTAG | JTAG | JTAG | JTAG + debugWIRE | JTAG |
| Core Type | AVR 8-bit RISC (legacy megaAVR) | AVR legacy | AVR enhanced | AVR legacy | AVR enhanced (picoPower) | AVR legacy |
주요 차별점
- Legacy megaAVR with JTAG on-chip debug (vs ATMEGA8535-16MU)
- Lowest-cost 16 KB option in the footprint family (vs ATMEGA32A-MU)
- Proven legacy compatibility (vs ATMEGA324PA-MU)
설계 노트
The -16 speed grade requires a 4.5V-5.5V supply. Decouple every VCC pin and AVCC with 100 nF ceramic capacitors placed within 2 mm of the package pins, plus 4.7-10 uF bulk per rail. Power AVCC through a 10 ohm resistor and 100 nF filter from the main 5V rail to improve the 10-bit ADC's effective resolution, and keep the analog ground return separated from the PWM/motor ground until the exposed pad. Estimated: a 16 MHz ATmega16 drawing about 15 mA active plus 20 mA of I/O load dissipates under 200 mW in the MLF-44, so no heatsinking is needed.
Solder the MLF-44 exposed die pad to a grounded copper pour with an array of thermal vias; the pad is the principal ground connection and leaving it floating is a common source of erratic USART and ADC behavior on QFN designs. Keep the XTAL1/XTAL2 crystal traces under 10 mm with ground guard rings, and route SPI/USART away from ADC inputs. Provide a 2x5 JTAG header footprint even if unused - enabling JTAG as GPIO later via fuse requires only a fuse change, not a respin.
Three frequent ATmega16 pitfalls: (1) forgetting that at 16 MHz the -16 grade needs 4.5V-5.5V - running from 3.3V causes brown-out resets at temperature extremes; (2) leaving the JTAG interface fuse-enabled unknowingly consumes PC2-PC5 as debug pins instead of GPIO; (3) EEPROM writes during brown-out corrupt data - enable the BOD (brown-out detection) fuse, set around 4.0V, before allowing self-programming bootloaders to write Flash or EEPROM in the field.
규정 준수 정보
Compliance status for the ATMEGA16-16MC suffix was not stated in the reviewed sources. The related ATMEGA16-16MU is described as a GREEN package variant in the FindIC comparison. Request official RoHS/REACH certificates from Microchip or the distributor before production.
