ATMEGA88-20AI - 8-bit AVR MCU 20MHz 8KB Flash TQFP-32 | Microchip
부품 번호: ATMEGA88-20AI ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.15 | $2.15 |
| 10 | $1.93 | $19.30 |
| 100 | $1.72 | $172.00 |
| 500 | $1.54 | $770.00 |
| 1,000 | $1.38 | $1,380.00 |
ATMEGA88-20AI 개요
An 8-bit AVR microcontroller is a single-chip computer that executes an advanced RISC instruction set, combining program memory, data memory, timers, analog-to-digital conversion, and serial communication peripherals on one die. Within the power-management hierarchy of embedded systems, the ATmega family sits at the entry-to-mid range of Microchip (formerly Atmel) MCU offerings, below the ATmega328 and ATmega2560 families.
Key features include 131 powerful instructions with mostly single-cycle execution, 32 general purpose working registers, 23 general purpose I/O lines, and picoPower technology for low static power consumption. On-chip peripherals comprise three flexible timer/counters with compare modes, a 10-bit 8-channel ADC, a programmable serial USART, a byte-oriented Two-Wire Interface (TWI/I2C), and an SPI serial port.
Technical depth comes from the AVR Harvard architecture with single-level pipelining, allowing one instruction per clock cycle. The device supports DebugWIRE on-chip debugging through the reset line, In-System Programming (ISP) with read-while-write Flash, and offers brown-out detection, power-on reset, and internal calibrated RC oscillator options at 8 MHz and 128 kHz. Operation spans 1.8 V to 5.5 V with 20 MHz performance guaranteed at 4.5 V to 5.5 V.
Typical applications include industrial sensor nodes and motor control boards (the industrial -40C to +85C temperature grade suits factory environments), consumer appliance user interfaces, and battery-powered instrumentation where picoPower sleep modes extend battery life.
A key design consideration: maximum clock frequency scales with VCC - 20 MHz is only guaranteed above 4.5 V, so designs running at 3.3 V must limit the clock to roughly 13.3 MHz or account for derating.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-09-19.
드롭인 대체품: ATMEGA88-20AI — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATMEGA88-20AI (동일 폼 팩터 및 풋프린트) — 차이점: Package, Throughput, Operating Temperature, Communication Interfaces, Supply Voltage Range.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATMEGA88-20AU
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.33 / 개
데이터시트 보기 →ATMEGA88P-20AU
✅ 드롭인✓ 재고 있음
$3.15 / 개
데이터시트 보기 →ATMEGA88A-20AU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATMEGA48-20AU
✅ 드롭인✓ 재고 있음
$1.68 / 개
데이터시트 보기 →ATMEGA88-15AT
✅ 드롭인✓ 재고 있음
$1.15 / 개
데이터시트 보기 →ATMEGA88-15AD
✅ 드롭인✓ 재고 있음
$1.55 / 개
데이터시트 보기 →ATMEGA88-20AI 최대 정격 & 전기적 특성
| Core Processor | AVR 8-bit RISC |
| Core Size | 8-bit |
| Speed | 20 MHz |
| Flash Program Memory | 8 KB (4K x 16) |
| EEPROM | 512 B |
| SRAM | 1 KB |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Max Clock at Full Voltage | 20 MHz at 4.5 V to 5.5 V |
| GPIO Count | 23 |
| ADC Resolution | 10-bit, 8 channels |
| Communication Interfaces | USART, SPI, TWI (I2C) |
| Timers | Two 8-bit, one 16-bit |
| MIPS Throughput | Up to 20 MIPS at 20 MHz |
| 동작 온도 | -40C to +85C |
| 패키지 | 32-TQFP (7x7 mm) |
| 실장 유형 | Surface Mount |
| On-Chip Debug | DebugWIRE |
| Programming | ISP, read-while-write Flash |
| Reset/Brown-out | Power-on Reset, Brown-out Detect/Reset |
ATMEGA88-20AI 핀 구성
| 핀 1 | PD3 (PCINT19/OC2B/INT1) — Port D bit 3, pin-change interrupt, Timer2 output compare B, external interrupt 1 |
| 핀 2 | PD4 (PCINT20/XCK/T0) — Port D bit 4, pin-change interrupt, USART external clock, Timer0 clock input |
| 핀 3 | GND — Ground |
| 핀 4 | VCC — Digital supply voltage |
| 핀 5 | GND — Ground |
| 핀 6 | VCC — Digital supply voltage |
| 핀 7 | PB6 (PCINT6/XTAL1/TOSC1) — Port B bit 6; crystal oscillator pin 1 or timer oscillator input |
| 핀 8 | PB7 (PCINT7/XTAL2/TOSC2) — Port B bit 7; crystal oscillator pin 2 or timer oscillator output |
| 핀 9 | PD5 (PCINT21/OC0B/T1) — Port D bit 5, pin-change interrupt, Timer0 output compare B, Timer1 clock input |
| 핀 10 | PD6 (PCINT22/OC0A/AIN0) — Port D bit 6, Timer0 output compare A, analog comparator positive input |
| 핀 11 | PD7 (PCINT23/AIN1) — Port D bit 7, analog comparator negative input |
| 핀 12 | PB0 (PCINT0/CLKO/ICP1) — Port B bit 0, system clock output, Timer1 input capture |
| 핀 13 | PB1 (PCINT1/OC1A) — Port B bit 1, Timer1 output compare A (PWM) |
| 핀 14 | PB2 (PCINT2/SS/OC1B) — Port B bit 2, SPI slave select, Timer1 output compare B |
| 핀 15 | PB3 (PCINT3/OC2A/MOSI) — Port B bit 3, Timer2 output compare A, SPI master output |
| 핀 16 | PB4 (PCINT4/MISO) — Port B bit 4, SPI master input |
| 핀 17 | PB5 (PCINT5/SCK) — Port B bit 5, SPI serial clock |
| 핀 18 | AVCC — ADC supply voltage |
| 핀 19 | ADC6 — ADC input channel 6 (dedicated analog input) |
| 핀 20 | AREF — Analog reference voltage for ADC |
| 핀 21 | GND — Ground |
| 핀 22 | ADC7 — ADC input channel 7 (dedicated analog input) |
| 핀 23 | PC0 (PCINT8/ADC0) — Port C bit 0, pin-change interrupt, ADC channel 0 |
| 핀 24 | PC1 (PCINT9/ADC1) — Port C bit 1, pin-change interrupt, ADC channel 1 |
| 핀 25 | PC2 (PCINT10/ADC2) — Port C bit 2, pin-change interrupt, ADC channel 2 |
| 핀 26 | PC3 (PCINT11/ADC3) — Port C bit 3, pin-change interrupt, ADC channel 3 |
| 핀 27 | PC4 (PCINT12/SDA/ADC4) — Port C bit 4, TWI data line, ADC channel 4 |
| 핀 28 | PC5 (PCINT13/SCL/ADC5) — Port C bit 5, TWI clock line, ADC channel 5 |
| 핀 29 | PC6 (PCINT14/RESET) — Reset input / DebugWIRE line; active-low with internal pull-up |
| 핀 30 | PD0 (PCINT16/RXD) — Port D bit 0, USART receiver input |
| 핀 31 | PD1 (PCINT17/TXD) — Port D bit 1, USART transmitter output |
| 핀 32 | PD2 (PCINT18/INT0) — Port D bit 2, external interrupt 0 |
일반적인 애플리케이션
ATMEGA88-20AI 적합 용도: 6 애플리케이션s: Industrial Sensor Nodes, Motor Control and Actuator Boards, Consumer Appliance UI Boards, Battery-Powered Portable Instrumentation, Embedded Serial-to-Protocol Bridges, HVAC and Environmental Control.
Industrial Sensor Nodes
The ATMEGA88-20AI fits industrial sensor nodes because its -40C to +85C grade survives factory-floor temperature swings, and its 10-bit 8-channel ADC digitizes multiple analog sensors (pressure, temperature bridges, potentiometers) without external conversion hardware. In a typical node, the MCU samples sensors through the ADC, applies linearization in the 8 KB Flash, and streams readings over the USART or TWI bus to a gateway at up to 20 MIPS throughput. PicoPower sleep modes reduce idle current between periodic samples, and the brown-out detector guards against data corruption during supply sags common in long cable runs. Budget roughly 8 KB for code and 1 KB for buffers and protocol state.
추천
Motor Control and Actuator Boards
Small brushed-DC and stepper motor boards benefit from the ATMEGA88-20AI's three timer/counters (two 8-bit, one 16-bit) that generate independent PWM channels with compare modes, while the 16-bit timer provides precise speed measurement via input capture. At 20 MHz the core delivers 20 MIPS, sufficient for closed-loop PI control at kilohertz loop rates. The 23 GPIO lines drive H-bridge gate circuitry through the port registers, and the 10-bit ADC reads back current-sense shunt voltages for torque limiting. In-system programming allows field firmware updates of control profiles without removing the board, and the industrial temperature rating suits enclosed motor-driver enclosures with limited airflow.
추천
Consumer Appliance UI Boards
Washer, oven, and HVAC front-panel controllers are a classic ATmega88 use case: the MCU scans keypads via GPIO interrupts, drives segment LCDs or LEDs with timer PWM dimming, and manages buzzer feedback, all within 1 KB SRAM and 8 KB Flash. The internal 8 MHz calibrated RC oscillator removes the crystal and its cost from cost-sensitive boards, while the TWI interface talks to external EEPROM or touch controllers. The 1.8-5.5 V range tolerates unregulated transformer-derived supplies, and the brown-out reset prevents corrupted settings during brownout events. Industrial-grade temperature tolerance also adds margin in hot appliance interiors near heating elements.
추천
Battery-Powered Portable Instrumentation
Handheld meters and loggers exploit the ATMEGA88-20AI's 1.8 V minimum supply to run directly from two alkaline cells (3.0 V nominal) to end-of-life at 1.8 V, and its picoPower sleep modes - Power-down in particular - drop current to microamp levels between measurements. The ADC Noise Reduction mode lets conversions run with the CPU clock stopped, improving analog accuracy in noisy motor-driven environments. Designers should clock the part at roughly 8 MHz or less when operating at 3 V, since the 20 MHz rating applies only from 4.5 V to 5.5 V. The 512 B EEPROM preserves calibration constants and logged min/max data across battery changes.
추천
Embedded Serial-to-Protocol Bridges
The ATMEGA88-20AI converts between serial protocols using its hardware USART, SPI, and TWI interfaces running concurrently. A common bridge topology accepts RS-232/RS-485 frames on the USART, parses them in the 1 KB SRAM buffer, and relays register data to TWI peripherals (RTC, DAC, port expanders) or SPI devices (Flash, sensors) at 20 MIPS execution speed. Hardware flow control and framing-error detection in the USART improve link robustness in electrically noisy cabinets. Self-programming Flash supports bootloader-based firmware field upgrades over the serial link itself, letting deployed bridges receive protocol updates without physical access - a key advantage in installed industrial wiring harnesses.
추천
HVAC and Environmental Control
Thermostat and ventilation controllers pair the ATMEGA88-20AI's 10-bit ADC with NTC thermistor dividers for multi-zone temperature sensing, while timer PWM drives tripper or triac outputs for damper motors and fan speed control. The Power-save sleep mode with the asynchronous timer allows the MCU to wake on a 32.768 kHz crystal timebase for timed schedules, conserving power between wake events. TWI connects external humidity or CO2 sensors, and the industrial -40C to +85C rating covers rooftop equipment enclosures. With only 8 KB of Flash, control logic and a simple UI state machine must be coded efficiently, but no RTOS overhead is needed.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATMEGA88-20AI — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATMEGA88-20AU | ATMEGA88P-20AU | ATMEGA48-20AU |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP (7x7 mm) | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same |
| Flash Memory | 8 KB | 8 KB | 8 KB | 4 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 512 B |
| EEPROM | 512 B | 512 B | 512 B | 256 B |
| Max Clock Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Sleep-Mode Power | Standard AVR sleep modes | Standard AVR sleep modes | picoPower - lowest sleep current | Standard AVR sleep modes |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
| Operating Temperature | -40C to +85C (industrial) | Industrial grade | Industrial grade | Industrial grade |
주요 차별점
- Full 8 KB Flash with self-programming bootloader support (vs ATMEGA48-20AU)
- Lowest long-term power option is the P-variant (vs ATMEGA88P-20AU)
- 20 MHz speed grade for headroom-critical control loops (vs ATMEGA88-15AT)
- Industrial temperature grade as standard (vs Commercial-grade TQFP variants)
설계 노트
Respect the clock-versus-voltage derating: the ATMEGA88-20AI guarantees 20 MHz only from 4.5 V to 5.5 V. At 3.3 V the safe ceiling is roughly 13.3 MHz (estimated: linear 0.9-20 MHz/V interpolation from the datasheet speed-grade curves). Running a full 20 MHz crystal on a 3.3 V rail risks out-of-spec execution and flash-write errors. If your design must run 3.3 V at high speed, either lower the crystal to 12-13 MHz or level-shift to a 5 V supply. Verify against the current Microchip ATmega88 datasheet speed curves before finalizing.
Place a 100 nF ceramic decoupling capacitor across each VCC/GND pin pair (pins 4-3 and 6-5) within 2 mm of the pins, plus a 100 nF cap on AVCC (pin 18) with a 10 uH series inductor or ferrite bead from VCC to AVCC to isolate ADC noise. Tie AREF (pin 20) to ground through 100 nF when using internal reference, or filter the external reference. Connect AVCC to VCC even if the ADC is unused - the datasheet requires AVCC present for correct digital operation.
PC6/RESET (pin 29) doubles as the DebugWIRE interface - enabling DebugWIRE via the DWEN fuse disables external reset, and recovering requires a high-voltage parallel programmer. Always keep ISP header access (PB3/MOSI, PB4/MISO, PB5/SCK, RESET) on production boards for field firmware updates. When using PB6/PB7 as GPIO instead of a crystal, confirm the CKOUT/fuse settings; wrong fuse programming of the clock source is the most common cause of 'bricked' ATmega88 boards.
At 5 V and 20 MHz with GPIO loads of 20 mA per pin, estimated worst-case power dissipation stays under 0.5 W, and the 32-TQFP theta_JA of approximately 100 C/W (typical 7x7 TQFP on 4-layer board - verify in package datasheet) yields under 50 C junction rise, safe at +85 C ambient. Avoid loading many I/O pins to their 40 mA absolute maximum simultaneously; the total device current limit governs, not the per-pin rating.
규정 준수 정보
RoHS and lead-free status per standard Microchip commercial MCU offering; verify REACH and conflict-minerals declarations on the Microchip product compliance portal for this exact ordering code.
