ATSAME51J20A-MU-EFP - 120MHz Cortex-M4F MCU 1MB Flash | Microchip
부품 번호: ATSAME51J20A-MU-EFP ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $8.62 | $8.62 |
| 10 | $7.69 | $76.90 |
| 100 | $6.45 | $645.00 |
| 500 | $5.82 | $2,910.00 |
| 1,000 | $5.34 | $5,340.00 |
ATSAME51J20A-MU-EFP 개요
A microcontroller (MCU) is a single-chip computer that combines a processor core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M4F core is a mainstream 32-bit processor family augmented by a single-precision FPU and DSP extensions, designed for deterministic real-time control. SAM E51 microcontrollers sit inside the broader hierarchy: ARM Cortex-M -> 32-bit MCU -> embedded microcontroller -> semiconductor. SAME51 also features FPU and DSP extensions that accelerate floating-point math in motor control and signal processing code.
Key specifications include 120 MHz core clock, 1 MB dual-panel Flash with ECC, 256 KB SRAM, and a 64-pin VQFN package with 9x9 mm body and an exposed thermal pad. The device integrates a 12-bit ADC, DAC, SERCOM peripherals, USB 2.0 Full-Speed with on-chip PHY, CAN-FD, and a 2-channel 16-bit timer/counter for PWM generation. Integrated SD/MMC host controller and I2S audio interfaces enable storage and digital audio applications.
Architecturally, the SAM E51 uses a multi-AHB bus matrix with separate code and system buses, allowing simultaneous Flash fetch and DMA transfers without contention. Error-Correction Code on Flash and SRAM improves reliability in industrial environments. The device operates from 1.71V to 3.6V and includes an on-chip voltage regulator, POR, and brown-out detector.
Typical applications include industrial control and Human-Machine Interface (HMI) panels, low-cost motor drives (BLDC, FOC, stepper), IoT edge nodes with USB and CAN connectivity, and consumer devices requiring graphical LCD or audio playback. Its wide peripheral set also suits home automation gateways and Building Automation controllers.
When designing with this MCU, place at least four 100 nF decoupling capacitors near the supply pins, plus a bulk 4.7 uF on VDDIN, and solder the exposed thermal pad with multiple thermal vias to the ground plane for thermal dissipation. Use the SAME51 header file and the MPLAB Harmony 3 framework to configure SERCOM, ADC, and timer peripherals, which avoids register-level bugs.
This page consolidates distributor pricing, verified drop-in alternatives, and design notes not typically found in the manufacturer datasheet, helping procurement and firmware teams make informed decisions for production.
드롭인 대체품: ATSAME51J20A-MU-EFP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAME51J20A-MU-EFP (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Operating Voltage, CAN, USB.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAME51J19A-MU-EFP
✅ 드롭인✓ 재고 있음
$4.85 / 개
데이터시트 보기 →ATSAME51J20A-MU
✅ 드롭인✓ 재고 있음
$7.65 / 개
데이터시트 보기 →ATSAME51J20A-AUT-EFP
✅ 드롭인✓ 재고 있음
$5.42 / 개
데이터시트 보기 →ATSAME51J19A-MUT-EFP
✅ 드롭인✓ 재고 있음
$2.43 / 개
데이터시트 보기 →ATSAME51J19A-AUT-EFP
✅ 드롭인✓ 재고 있음
$6.45 / 개
데이터시트 보기 →ATSAME51G19A-MU-EFP
✅ 드롭인✓ 재고 있음
$5.2 / 개
데이터시트 보기 →ATSAME51J20A-MU-EFP 최대 정격 & 전기적 특성
| Core | ARM Cortex-M4F with FPU and DSP extensions |
| Core Clock Speed | 120 MHz |
| Program Memory | 1 MB dual-panel Flash with ECC |
| SRAM | 256 KB |
| Operating Voltage | 1.71 V to 3.6 V |
| 패키지 | 64-pin VQFN (9x9 mm) with exposed pad |
| 실장 유형 | Surface Mount |
| Supply Voltage (VDDIN) | 3.3 V typical |
| USB | USB 2.0 Full-Speed Device/Host with on-chip PHY |
| CAN | CAN-FD |
| 동작 온도 | -40 C to +85 C (industrial) |
| MSL 레벨 | 3 |
| RoHS 상태 | Compliant |
ATSAME51J20A-MU-EFP 64-pin vqfn (9x9 mm) with exposed pad 핀 구성 가이드
ATSAME51J20A-MU-EFP(64-pin vqfn (9x9 mm) with exposed pad 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATSAME51J20A-MU-EFP.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATSAME51J20A-MU-EFP 적합 용도: 6 애플리케이션s: Industrial Human-Machine Interface (HMI) Panels, BLDC and FOC Motor Control, USB-Connected IoT Edge Devices, Building Automation and HVAC Controllers, Consumer Audio Products, CAN-FD Automotive ECUs.
Industrial Human-Machine Interface (HMI) Panels
The ATSAME51J20A-MU-EFP drives industrial HMI panels using its 120 MHz Cortex-M4F core and 1 MB Flash to render graphics, manage touch input, and run communication stacks. The integrated USB Full-Speed and CAN-FD peripherals connect directly to industrial controllers without external transceivers, while 256 KB SRAM holds framebuffers and protocol buffers. The 1.71-3.6V supply range tolerates 24V industrial rails stepped down with a switching regulator. Typical HMI tasks - parsing Modbus TCP, debouncing capacitive touch, and animating icons - consume less than 60% of CPU, leaving headroom for predictive-maintenance algorithms.
추천
BLDC and FOC Motor Control
The ATSAME51J20A-MU-EFP is well-suited for sensorless BLDC and Field-Oriented Control (FOC) motor drives thanks to dedicated Timer/Counter for Control (TCC) modules with complementary PWM outputs and dead-time insertion. The Cortex-M4F core executes FOC math at 120 MHz with hardware floating point, closing current loops well under 10 microseconds. Its 12-bit ADC synchronizes with PWM for precise current sampling, and the integrated op-amps (where present on the family) reduce external analog components. Designers typically pair the MCU with a 3-phase gate driver like the MCP8024 to drive MOSFET bridges up to several hundred watts.
추천
USB-Connected IoT Edge Devices
The ATSAME51J20A-MU-EFP serves USB-connected IoT edge nodes, leveraging its USB 2.0 Full-Speed port with on-chip PHY to communicate with a host without external transceivers. The 120 MHz Cortex-M4F processes sensor data and runs encryption (AES via crypto accelerator on the family) before forwarding to the host. The 1 MB Flash stores both application and bootloader, supporting dual-bank live firmware updates critical for deployed edge nodes. With industrial temperature range and ECC memory, the MCU is a dependable bridge between local sensors and USB-attached gateways.
추천
Building Automation and HVAC Controllers
In building automation controllers, the ATSAME51J20A-MU-EFP handles HVAC sequences with multiple temperature sensors, manages Modbus or BACnet over RS-485, and drives relay outputs. The Cortex-M4F executes complex control algorithms while CAN-FD connects to other building subsystems like elevators or access control. With 256 KB SRAM, it can buffer multiple communication transactions in parallel. The wide 1.71-3.6V operating range handles power-supply fluctuations common in long cable runs of building networks, and the dual-bank Flash enables safe field firmware upgrades.
추천
Consumer Audio Products
The ATSAME51J20A-MU-EFP powers consumer audio products, decoding audio from SD cards or USB and outputting via I2S to a DAC. The Cortex-M4F's DSP extensions accelerate MP3/AAC decoding and equalizer computations, while the 256 KB SRAM buffers audio frames without dropouts. The integrated USB device port allows easy firmware updates and HID control from a host PC. The wide operating voltage range supports both battery-powered and mains-powered designs, and the small 64-pin VQFN package fits into compact portable enclosures.
추천
CAN-FD Automotive ECUs
The ATSAME51J20A-MU-EFP serves CAN-FD-enabled automotive Electronic Control Units, integrating the CAN-FD controller for high-bandwidth vehicle network communication. For AEC-Q100 qualified deployments, the ATSAME51J20A-AUT-EFP variant is the drop-in replacement with automotive qualification. The 1 MB dual-bank Flash supports ASIL-relevant firmware partitioning and live updates, while ECC memory detects bit flips from vehicle EMI. The 120 MHz core with FPU handles automotive sensor fusion and diagnostics in real time, making this MCU a reliable choice for body and chassis ECUs.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAME51J20A-MU-EFP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAME51J19A-MU-EFP | ATSAME51J20A-MU | ATSAME51J20A-AUT-EFP | ATSAME51G19A-MU-EFP |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | VQFN-64 (9x9 mm) | VQFN-64 (9x9 mm) | VQFN-64 (9x9 mm) | VQFN-64 (9x9 mm) | VQFN-64 (9x9 mm) |
| Core | Cortex-M4F 120 MHz | Cortex-M4F 120 MHz | Cortex-M4F 120 MHz | Cortex-M4F 120 MHz | Cortex-M4F 120 MHz |
| Flash Memory | 1 MB | 512 KB | 1 MB | 1 MB | 512 KB |
| SRAM | 256 KB | 192 KB | 256 KB | 256 KB | 192 KB |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| AEC-Q100 Qualified | No | No | No | Yes | No |
| Packaging | Tray | Tray | Tray | Tape and Reel | Tray |
주요 차별점
- 1 MB dual-bank Flash with ECC (vs ATSAME51J19A-MU-EFP)
- AEC-Q100 automotive qualification option (vs ATSAME51J20A-MU)
- J-series peripheral set vs G-series (vs ATSAME51G19A-MU-EFP)
설계 노트
Place at least four 100 nF decoupling capacitors close to the VDD pins, plus a single bulk 4.7 uF ceramic capacitor on VDDIN. The exposed thermal pad under the VQFN package must be soldered to the PCB ground plane with multiple thermal vias (typically 9 in a 3x3 array, 0.3 mm diameter) to dissipate power and provide a low-impedance ground return. Estimated: at 120 MHz full operation with USB active, total supply current can reach 80 mA - the bulk cap prevents voltage droop during USB suspend/resume transitions.
Do not enable dual-bank Flash until the bootloader is verified, because misconfigured bank switching can lock the device. Use the SAM-BA bootloader or Atmel-ICE for initial programming before locking the security bit. Ensure the NVMCTRL (Non-Volatile Memory Controller) configuration matches the chosen row size (typically 256 bytes for SAME51), otherwise Flash writes will silently fail. Estimated: programming failures due to incorrect row size cost hours of debug time.
Route the 32 kHz crystal traces symmetrically with short lengths and keep them away from switching signals to minimize stray capacitance, which detunes the low-frequency oscillator. The HS USB DP/DM traces must be 90 ohm differential with no stubs, and route them on the top layer directly above a continuous ground pour. Estimated: USB signal integrity issues commonly trace back to poor DP/DM impedance control rather than MCU silicon problems.
규정 준수 정보
RoHS compliant per distributor listings. Standard variant is not AEC-Q100 qualified - select ATSAME51J20A-AUT-EFP for automotive. Halogen-free status not explicitly stated in web data.
