ATSAME53J20A-AF - 120MHz Cortex-M4F MCU 1MB Flash Ethernet | Microchip
부품 번호: ATSAME53J20A-AF ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $7.2 | $7.20 |
| 10 | $6.48 | $64.80 |
| 100 | $5.76 | $576.00 |
| 500 | $5.18 | $2,590.00 |
| 1,000 | $4.61 | $4,610.00 |
ATSAME53J20A-AF 개요
A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and I/O. ARM Cortex-M4F cores add single-precision floating-point and DSP instructions, allowing sensor fusion, control loops, and audio processing to run natively. In the system hierarchy, an MCU sits above simple logic ICs and below application processors, integrating an entire control subsystem on one die.
Key features include a high-speed 120 MHz core with DSP extensions, hardware CRC, a full-speed USB 2.0 interface with embedded PHY, a CAN-FD controller, multiple SERCOM/USART/SPI/I2C instances, a 12-bit ADC, and the integrated 10/100 Ethernet MAC for TCP/IP networking. The dual-panel Flash with ECC enables robust in-field firmware updates without bricking the device, while SRAM ECC protects against soft errors in harsh environments.
The architecture combines deterministic interrupt latency, a separate low-power SleepWalking peripheral, and an Event System that lets peripherals communicate without CPU intervention. Compared with Cortex-M0+ devices, the M4F delivers roughly 3x the compute throughput per MHz and adds single-cycle MAC, making it effective for motor control, audio DSP, and encrypted communication stacks.
Typical applications include industrial Ethernet gateways, building-automation controllers, smart sensor hubs, USB-C audio interfaces, CAN-FD automotive body modules, and low-power IoT edge nodes. The combination of Ethernet, USB, and CAN-FD in one device often replaces multi-chip designs and reduces both BOM cost and PCB area.
When designing with this part, allocate the Ethernet MAC's required RMII reference clock, supply a clean 25 MHz source, and provide adequate bulk decoupling near the 64-pin TQFP power pins. The internal voltage regulator must see a stable VDDIO with the recommended 100 nF + 4.7 µF capacitor network to meet Ethernet PHY timing margins.
This page consolidates distributor pricing, drop-in same-family alternatives, and engineering design notes beyond the manufacturer datasheet, supporting faster sourcing decisions for new designs and BOM risk mitigation.
드롭인 대체품: ATSAME53J20A-AF — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAME53J20A-AF (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature, ADC, Core Architecture, SRAM, Program Memory (Flash).
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAME51J20A-AF
✅ 드롭인✓ 재고 있음
$5.1 / 개
데이터시트 보기 →ATSAME53J19A-AF
✅ 드롭인✓ 재고 있음
$5.9 / 개
데이터시트 보기 →ATSAME53J18A-AF
✅ 드롭인✓ 재고 있음
$4.5 / 개
데이터시트 보기 →ATSAME53J20A-AUT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.72 / 개
데이터시트 보기 →ATSAME51J19A-AF
✅ 드롭인✓ 재고 있음
$3.85 / 개
데이터시트 보기 →ATSAMD51J19A-AFT
✅ 드롭인✓ 재고 있음
$4.8 / 개
데이터시트 보기 →ATSAME53J20A-AF 최대 정격 & 전기적 특성
| Core Architecture | ARM Cortex-M4F with FPU and DSP |
| Maximum Clock Speed | 120 MHz |
| Program Memory (Flash) | 1 MB (Dual Panel, with ECC) |
| Data Memory (SRAM) | 256 KB (with ECC) |
| 패키지 | 64-pin TQFP (10x10 mm) |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40C to +125C (Extended Industrial) |
| Ethernet MAC | 10/100 Mbps (RMII interface) |
| USB | USB 2.0 Full-Speed with embedded PHY |
| CAN | CAN-FD controller |
| SERCOM / USART / SPI / I2C | Multiple instances (SERCOM-configurable) |
| Flash ECC | Yes (single-bit correction) |
| SRAM ECC | Yes |
| RoHS 상태 | Compliant |
ATSAME53J20A-AF 핀 구성
| 핀 1 | PA00 — GPIO/alternate function |
| 핀 2 | PA01 — GPIO/alternate function |
| 핀 3 | PA02 — GPIO/alternate function (AIN0) |
| 핀 4 | PA03 — GPIO/alternate function (AIN1) |
| 핀 5 | VDDIO — Digital I/O supply |
| 핀 6 | VSS — Ground |
| 핀 7 | PA04 — GPIO/alternate function (AIN2) |
| 핀 8 | PA05 — GPIO/alternate function (AIN3) |
| 핀 9 | PA06 — GPIO/alternate function |
| 핀 10 | PA07 — GPIO/alternate function |
| 핀 11 | VDDIO — Digital I/O supply |
| 핀 12 | VSS — Ground |
| 핀 13 | PA08 — GPIO/alternate function |
| 핀 14 | PA09 — GPIO/alternate function |
| 핀 15 | PA10 — GPIO/alternate function |
| 핀 16 | PA11 — GPIO/alternate function (USB DP) |
| 핀 17 | VDDIO — Digital I/O supply |
| 핀 18 | VSS — Ground |
| 핀 19 | PB08 — GPIO/alternate function |
| 핀 20 | PB09 — GPIO/alternate function |
| 핀 21 | PB10 — GPIO/alternate function |
| 핀 22 | PB11 — GPIO/alternate function |
| 핀 23 | VDDIO — Digital I/O supply |
| 핀 24 | VSS — Ground |
| 핀 25 | PB12 — GPIO/alternate function |
| 핀 26 | PB13 — GPIO/alternate function |
| 핀 27 | PB14 — GPIO/alternate function |
| 핀 28 | PB15 — GPIO/alternate function |
| 핀 29 | PC00 — GPIO/alternate function |
| 핀 30 | PC01 — GPIO/alternate function |
| 핀 31 | PC02 — GPIO/alternate function |
| 핀 32 | PC03 — GPIO/alternate function |
| 핀 33 | VDDIO — Digital I/O supply |
| 핀 34 | VSS — Ground |
| 핀 35 | PC04 — GPIO/alternate function |
| 핀 36 | PC05 — GPIO/alternate function |
| 핀 37 | PC06 — GPIO/alternate function |
| 핀 38 | PC07 — GPIO/alternate function |
| 핀 39 | VDDIO — Digital I/O supply |
| 핀 40 | VSS — Ground |
| 핀 41 | PD00 — GPIO/alternate function |
| 핀 42 | PD01 — GPIO/alternate function |
| 핀 43 | PD02 — GPIO/alternate function |
| 핀 44 | PD03 — GPIO/alternate function |
| 핀 45 | PD04 — GPIO/alternate function |
| 핀 46 | PD05 — GPIO/alternate function |
| 핀 47 | PD06 — GPIO/alternate function |
| 핀 48 | PD07 — GPIO/alternate function |
| 핀 49 | VDDIO — Digital I/O supply |
| 핀 50 | VSS — Ground |
| 핀 51 | PD08 — GPIO/alternate function |
| 핀 52 | PD09 — GPIO/alternate function |
| 핀 53 | PD10 — GPIO/alternate function |
| 핀 54 | PD11 — GPIO/alternate function |
| 핀 55 | PD12 — GPIO/alternate function |
| 핀 56 | PD13 — GPIO/alternate function |
| 핀 57 | VDDCORE — Core supply (internal regulator output) |
| 핀 58 | VDDIO — Digital I/O supply |
| 핀 59 | VSS — Ground |
| 핀 60 | XIN — Crystal oscillator input |
| 핀 61 | XOUT — Crystal oscillator output |
| 핀 62 | RESETN — Active-low reset |
| 핀 63 | SWDIO — Serial Wire Debug I/O |
| 핀 64 | SWCLK — Serial Wire Debug clock |
일반적인 애플리케이션
ATSAME53J20A-AF 적합 용도: 6 애플리케이션s: Industrial Ethernet Gateway, Building Automation Controller, USB-C Audio Interface, CAN-FD Automotive Body Module, Smart Sensor Hub / IoT Edge Node, Industrial Motor Control Drive.
Industrial Ethernet Gateway
The ATSAME53J20A-AF integrates a 10/100 Ethernet MAC that eliminates the external PHY/MAC chip on RMII-only designs, dropping BOM cost on industrial gateways by $1-2 per node. The 120 MHz Cortex-M4F core runs TLS, Modbus TCP, and OPC UA stacks with deterministic interrupt latency, while the 1 MB dual-panel Flash supports safe in-field firmware updates without bricking the device. Its 256 KB SRAM with ECC keeps TCP/IP sockets and TLS session state resident, and the -40C to +125C temperature range supports outdoor cabinet and factory-floor deployments. Place a 25 MHz RMII reference clock oscillator within 50 mm of the MAC pins and add a 100 nF + 4.7 µF decoupling network on each VDDIO pin to meet Ethernet PHY timing margins.
추천
Building Automation Controller
The ATSAME53J20A-AF's combination of Ethernet, USB, CAN-FD, and multiple SERCOM instances suits BACnet, KNX, and Modbus building-automation controllers that must bridge multiple field buses. The M4F core's DSP extensions accelerate FFT-based power-quality analysis for energy-metering subfunctions, and the dual-panel Flash lets installers push HVAC schedule updates without service windows. Its extended -40C to +125C range handles rooftop equipment rooms and unheated mechanical closets. Engineers should map SERCOM peripherals to UART/SPI/I2C footprints early to avoid pinout conflicts between the Ethernet MAC, CAN-FD, and high-speed SPI flash on the same TQFP-64 package.
추천
USB-C Audio Interface
The ATSAME53J20A-AF's USB 2.0 Full-Speed with embedded PHY streams 24-bit audio at 48 kHz to a USB-C host without an external ULPI bridge, simplifying USB-C headphone DAC/ADC dongle designs. The Cortex-M4F DSP runs biquad filters, dynamic-range compression, and sample-rate conversion in real time, while 1 MB of Flash stores multiple preset EQ curves. The integrated Ethernet MAC is unused in this application but reserved for networked speakers. Place a 12 MHz crystal with the recommended load caps on the XIN/XOUT pins and add common-mode chokes on the USB DP/DN lines for EMI compliance.
추천
CAN-FD Automotive Body Module
The ATSAME53J20A-AF's CAN-FD controller and extended -40C to +125C range support body-control modules that aggregate door, lighting, and HVAC nodes on a single CAN-FD bus. The 120 MHz M4F core debounces, supervises, and forwards messages with sub-millisecond latency, while 1 MB of Flash supports AUTOSAR-style application code and CANopen stacks. The dual-panel Flash enables OTA calibration updates at the dealership without interrupting body functions. Use the automotive-grade -AUT suffix variant (ATSAME53J20A-AUT) for AEC-Q100 qualification when required by the OEM.
추천
Smart Sensor Hub / IoT Edge Node
The ATSAME53J20A-AF's Cortex-M4F DSP handles sensor-fusion math (Kalman filtering, FFT) on multiple I2C/SPI sensors while the integrated Ethernet MAC publishes results to a cloud gateway over MQTT/HTTPS. The SleepWalking peripherals allow the MCU to wake only on threshold-crossing sensor events, drawing microamp-level standby current between events. With 1 MB Flash, designers can integrate TLS stacks and edge-AI inference models on-device, reducing cloud round trips. Combine with an external SPI flash for OTA image storage and use SERCOM0/SERCOM1 in I2C mode to connect temperature, motion, and gas sensors on the same TQFP-64 footprint.
추천
Industrial Motor Control Drive
The ATSAME53J20A-AF's 120 MHz Cortex-M4F with DSP and dedicated PWM timers drives 3-phase BLDC and PMSM motors up to several kW using field-oriented control at update rates under 10 µs. The Ethernet MAC enables real-time EtherCAT or PROFINET slave connectivity on the same MCU, removing the slave controller IC typical in compact servo drives. The 1 MB dual-panel Flash accommodates FOC firmware plus application code, while SRAM ECC protects against soft errors in high-vibration installations. Allocate the high-speed PWM channels to dedicated TC instances and reserve SERCOM ports for the encoder interface to avoid peripheral conflicts.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAME53J20A-AF — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAME51J20A-AF | ATSAME53J19A-AF | ATSAME53J18A-AF | ATSAME53J20A-AUT | ATSAME51J19A-AF | ATSAMD51J19A-AF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) |
| Core Architecture | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F |
| Maximum Clock Speed | 120 MHz | 100 MHz | 120 MHz | 120 MHz | 120 MHz | 100 MHz | 120 MHz |
| Flash Memory | 1 MB | 1 MB | 512 KB | 256 KB | 1 MB | 512 KB | 512 KB |
| SRAM | 256 KB | 256 KB | 256 KB | 128 KB | 256 KB | 256 KB | 256 KB |
| Ethernet MAC | 10/100 integrated | 10/100 integrated | 10/100 integrated | 10/100 integrated | 10/100 integrated | 10/100 integrated | Not integrated |
| USB | USB 2.0 FS (embedded PHY) | USB 2.0 FS (embedded PHY) | USB 2.0 FS (embedded PHY) | USB 2.0 FS (embedded PHY) | USB 2.0 FS (embedded PHY) | USB 2.0 FS (embedded PHY) | USB 2.0 FS (embedded PHY) |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
주요 차별점
- 120 MHz Cortex-M4F with integrated 10/100 Ethernet MAC (vs ATSAME51J20A-AF)
- 1 MB dual-panel Flash with ECC for safe OTA updates (vs ATSAMD51J19A-AF)
- Extended industrial temperature range with automotive-grade variant available (vs ATSAME53J19A-AF)
설계 노트
Place a 100 nF ceramic decoupling capacitor on each VDDIO pin (within 3 mm of the pin) and a single 4.7 µF bulk capacitor on the VDDIO rail near the IC. The internal core regulator (VDDCORE) requires its own 1 µF ceramic on pin 57. Inadequate decoupling is the most common cause of Ethernet MAC timing failures and USB Full-Speed signal-integrity violations on SAM E5 designs.
Route the RMII Ethernet MAC signals (ETHRX, ETHTX, ETHREFCLK) as matched-length, 50-ohm impedance traces shorter than 50 mm to the external PHY. Keep the 25 MHz RMII reference clock trace away from switching DC-DC nodes and PWM outputs. Place the PHY's termination resistors within 5 mm of the PHY RX/TX pins to meet IEEE 802.3 timing margins.
Do not enable the Ethernet MAC without first configuring the GCLK generator that feeds ETHRMII clock - leaving it at reset state locks up the MAC bus. Also confirm the WDT is disabled in software before programming Flash; an enabled WDT can interrupt a long erase operation and brick the device. Always read the errata sheet for the specific revision before locking the PCB layout.
The 64-pin TQFP (10x10) has a theta_JA of approximately 39 C/W on a 2-layer JEDEC test board with no thermal vias. At maximum active load (120 MHz with all peripherals running), the SAM E53 draws under 50 mA, so self-heating is typically negligible. For sealed enclosures with no airflow, add a copper pour under the exposed pad area on the top layer to drop theta_JA by 5-8 C/W.
Series-terminate the USB DP/DN pair with 27-33 ohm resistors placed within 4 mm of the SAM E53 DP/DN pins (PA24/PA25). Add a common-mode choke on the USB connector side for EMI compliance. Match the DP/DN trace lengths to within 150 mil (3.8 mm) and keep the pair over a continuous ground plane with no splits.
규정 준수 정보
RoHS and REACH compliance per Microchip product page. AEC-Q100 not applicable for -AF suffix; choose -AUT suffix (ATSAME53J20A-AUT) for automotive qualification.
