Microchip Technology

ATSAML10D15A-YU - 32MHz Cortex-M23 MCU, 32KB Flash | Microchip

부품 번호: ATSAML10D15A-YU ✓ 활성
3.3 V Vdss Less than 25 uA/MHz Id 24-pin SSOP Package 32 MHz Speed 32 KB Memory
MOQ: 1 |

ATSAML10D15A-YU 개요

The Microchip Technology ATSAML10D15A-YU is a 32-bit Arm Cortex-M23 microcontroller operating up to 32 MHz, with 32 KB of flash memory, 8 KB of SRAM, and 2048 bytes of data EEPROM in a 24-pin SSOP package. It combines a low-power RISC core with a 10-bit DAC, five 12-bit ADCs, SERCOM serial interfaces, and an enhanced peripheral touch controller.

A microcontroller is a programmable system-on-chip that integrates a CPU core, nonvolatile program memory, working memory, and peripherals into one component. The ATSAML10 family belongs to the Arm Cortex-M23 microcontroller hierarchy, combining deterministic interrupt handling with energy-efficient operation for embedded control systems. The Cortex-M23 core provides an Arm Thumb instruction set and event-oriented peripherals suited to low-power sensing and control equipment.

Key device characteristics include active-mode consumption below 25 uA/MHz and sleep-mode consumption below 100 nA. The analog section includes five 12-bit ADCs and one 10-bit DAC, while eight DMA channels reduce CPU involvement during data transfers. Three timers support periodic control functions, and the SERCOM peripherals provide configurable serial communication capability. An ISO7816 smart-card interface and event system extend the device beyond basic sensor-and-actuator control.

The 24-SSOP package keeps the board footprint compact while providing external signal access through 24 pins. Internal flash supports firmware storage, while the 8 KB SRAM provides working space for protocol stacks, control loops, and buffered measurements. The dedicated EEPROM area can retain calibration values, configuration data, or counters without consuming RAM.

Typical uses include low-power sensor nodes, smart card readers, capacitive-touch interfaces, industrial control modules, battery-powered instruments, and compact communication equipment. The combination of low active and sleep current makes the device suitable for designs where the average power budget is dominated by long idle periods rather than continuous computation.

When designing the board, follow the pin-description and decoupling tables in the manufacturer datasheet. Place the specified input, output, and VDD bypass capacitors close to their assigned pins, preserve the exposed analog and digital ground strategy described by Microchip, and program unused inputs to defined states.

This page combines device specifications, verified distributor availability information, same-family drop-in candidates, application guidance, and comparison data to support component selection, PCB planning, firmware preparation, and sourcing decisions.

드롭인 대체품: ATSAML10D15A-YU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: ATSAML10D15A-YU (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Active Mode Current, Package, Sleep Mode Current, Core.

Microchip Technology
ADC: 12-bit
Active Mode Current: < 25 uA/MHz
Package: 24-SSOP (0.209", 5.30 mm width)
비교 대상: ATSAML10D15A-YU →
Microchip Technology
ADC: 12-bit, up to 20 channels
Active Mode Current: <25 uA/MHz
Package: 24-SSOP
비교 대상: ATSAML10D15A-YU →

ATSAML10D15A-YUT

✅ 드롭인
Microchip Technology
📦 24-SSOP
ARM Cortex-M23 32-bit · 32 MHz · 32 KB (32K x 8) · 8 KB · 24-SSOP (0.209", 5.30 mm width) · < 25 uA/MHz · < 100 nA

가격 문의

데이터시트 보기 →

ATSAML10D16A-YU

✅ 드롭인 ⚠️ 사양 미검증
Microchip Technology
📦 24-SSOP
ARM Cortex-M23 (ARMv8-M) · 32 MHz · 64 KB (64K x 8) · 16 KB · 24-SSOP · 24 · 1.62 V to 3.63 V · <25 uA/MHz

가격 문의

데이터시트 보기 →

ATSAML10D17A-YU

✅ 드롭인 ⚠️ 사양 미검증
📦 24-SSOP
Same-family 24-SSOP Cortex-M23 configuration with a different memory configuration from the 32 KB-flash target, requiring firmware footprint verification.

📋 참조 대체품 (카탈로그에 없음)

ATSAML10D18A-YU

✅ 드롭인 ⚠️ 사양 미검증
📦 24-SSOP
Same-family 24-SSOP Cortex-M23 pin arrangement, but the flash configuration is larger than the 32 KB target, so the firmware image and bill of materials change.

📋 참조 대체품 (카탈로그에 없음)

ATSAML10D15A-YU 최대 정격 & 전기적 특성

Core Arm Cortex-M23, 32-bit
Maximum CPU Frequency 32 MHz
Program Flash Memory 32 KB
SRAM 8 KB
Data EEPROM 2048 bytes
ADC 5 x 12-bit
DAC 1 x 10-bit
DMA Channels 8
Timers 3
Active Mode Current Less than 25 uA/MHz
Sleep Mode Current Less than 100 nA
공급 전압 3.3 V
패키지 24-pin SSOP
실장 유형 Surface Mount
Peripheral Touch Controller Yes
Serial Interfaces SERCOM
Smart Card Interface ISO7816
Analog Features ADC, DAC, OPAMP, AC
Event System Yes

ATSAML10D15A-YU 24-pin ssop 핀 구성 가이드

ATSAML10D15A-YU(24-pin ssop 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.

ATSAML10D15A-YU의 24-pin ssop 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: ATSAML10D15A-YU.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

ATSAML10D15A-YU 적합 용도: 6 애플리케이션s: Low-Power Sensor Node, Smart Card and Secure Reader, Capacitive-Touch User Interface, Industrial Process Monitoring, Battery-Powered Handheld Instrument, Compact Communication Controller.

🧩

Low-Power Sensor Node

The ATSAML10D15A-YU fits periodic environmental sensing because its Cortex-M23 core operates at up to 32 MHz while consuming less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. Its five 12-bit ADC channels can sample resistive sensors, thermistors, or external analog front ends, and the eight DMA channels reduce processor involvement when transferring measurements. The 32 KB flash and 8 KB SRAM are suitable for compact acquisition and filtering code, although both should be checked against the final firmware size. A duty-cycled acquisition strategy keeps the radio and sensor off between samples, making the device appropriate for battery-powered monitoring in environmental, agricultural, and equipment-maintenance systems.

🔒

Smart Card and Secure Reader

The ATSAML10D15A-YU is suitable for smart-card reader and secure-access peripherals because the ATSAML10 family includes an ISO7816 smart-card interface alongside the general-purpose Cortex-M23 core. This allows one controller to coordinate card detection, protocol handling, host communication, and user-interface functions without a separate interface device. The 32 KB flash can hold a compact protocol stack and application firmware, while the 10-bit DAC and five 12-bit ADCs support analog supervision or signal-level monitoring. Because smart-card systems are sensitive to timing and signal integrity, engineers should use the Microchip reference circuitry and pin guidance when defining connector protection, clocking, and grounding.

🧩

Capacitive-Touch User Interface

The enhanced peripheral touch controller in the ATSAML10D15A-YU allows capacitive-touch detection without relying on discrete sensing hardware in suitable applications. Its 32 MHz Cortex-M23 core can scan touch inputs, apply filtering, update indicators, and forward events over a serial interface, while less-than-100 nA sleep operation supports products that idle between user interactions. The five 12-bit ADCs remain useful for monitoring touch- or knob-position analog signals and for verifying sensor conditions. Grounding and electrode layout strongly affect touch performance, so follow the manufacturer application guidance for guard traces, shield geometry, and the relationship between analog, digital, and supply return paths.

🏭

Industrial Process Monitoring

The ATSAML10D15A-YU can act as the local controller in a distributed process-monitoring node, converting several analog inputs and coordinating local outputs. Five 12-bit ADCs allow multiplexed sensing of pressure, temperature, or level signals, while three timers support periodic sampling, timeout, and actuator sequencing. The eight DMA channels can move peripheral data with reduced CPU overhead, and SERCOM provides a configurable path to a host or sensor network. Its low active and sleep current figures are beneficial in remote installations, although field-rugged designs must also satisfy electromagnetic-interference, isolation, and extended-temperature requirements beyond the base device specifications.

📱

Battery-Powered Handheld Instrument

The ATSAML10D15A-YU suits compact handheld instruments where both processing capability and standby consumption matter. The 32-bit Cortex-M23 core can execute control logic, calibration routines, and menu handling at up to 32 MHz, while the 2048-byte EEPROM provides a place for serial numbers, calibration constants, or configuration flags. Sleep current below 100 nA allows the design to remain in a low-power state between user actions or measurement cycles. The 10-bit DAC can generate an analog reference or control signal, and the ADC bank supports front-panel sensing. Designers should define the regulator, display, and analog-signal paths so that the low-power MCU benefit is not overwhelmed by other always-on loads.

🌐

Compact Communication Controller

The ATSAML10D15A-YU can serve as a low-power protocol controller for connected sensors, gateways, and compact peripheral nodes. Its configurable SERCOM peripherals support serial communication duties, while the Cortex-M23 core handles framing, buffering, protocol state, and local configuration. The 32 KB flash and 8 KB SRAM are adequate for lightweight stacks and application logic when the protocol implementation is size-conscious. Eight DMA channels can offload transfers between the serial interface and memory, helping preserve responsiveness during bursts. A communications design should confirm the target interface voltage levels and timing, then implement the recommended decoupling and ground-return arrangement to prevent serial edges or switching activity from disturbing the analog section.

What are the key specifications of ATSAML10D15A-YU?
The ATSAML10D15A-YU integrates a 32-bit Arm Cortex-M23 core, 32 KB of flash, 8 KB of SRAM, and 2048 bytes of EEPROM in a 24-pin SSOP package. According to the Microchip product page, it also provides five 12-bit ADCs, one 10-bit DAC, eight DMA channels, three timers, SERCOM interfaces, and an enhanced peripheral touch controller.
What is the operating voltage of ATSAML10D15A-YU?
The ATSAML10D15A-YU operates from a 3.3 V supply. The manufacturer listings identify the part as a 3.3 V, 24-pin SSOP microcontroller. Check the electrical-characteristics and recommended-operating-conditions tables in the Microchip datasheet for the precise core and peripheral voltage limits before applying power.
What can replace ATSAML10D15A-YU?
The closest same-footprint substitute is ATSAML10D15A-YUT, which retains the ATSAML10D15A device configuration and 24-SSOP pin arrangement while using a different shipping format. Other ATSAML10D-family devices can support redesigns when their flash, SRAM, and peripheral configurations are acceptable. Verify the complete pin table and firmware requirements before replacing an assembled design.
Is ATSAML10D15A-YU the same as ATSAML10D15A-YUT?
The ATSAML10D15A-YU and ATSAML10D15A-YUT refer to the same 24-pin SSOP ATSAML10D15A device configuration, with the ordering suffix distinguishing the supplied packing format. Both listings identify 32 KB flash, 8 KB SRAM, and a 32 MHz Cortex-M23 core. Confirm the required packing format when placing the order.
Where can I download the ATSAML10D15A-YU datasheet PDF?
The ATSAML10D15A-YU datasheet and supporting documents are available from the Microchip ATSAML10D15A product page. Use the manufacturer's Documents and Resources section to locate the current product data sheet, errata, pin definition tables, electrical characteristics, and programming guidance before finalizing the hardware design.
Where can I find the ATSAML10D15A-YU pinout?
The authoritative ATSAML10D15A-YU pin assignment is presented in the pin-description table of the Microchip ATSAML10D15A datasheet. The device uses a 24-pin SSOP package, so verify the 24-pin numbering, power pins, ground pins, and analog or debug functions directly against that table before assigning PCB nets.
How much power does the ATSAML10D15A-YU use?
Microchip specifies active-mode consumption below 25 uA/MHz and sleep-mode consumption below 100 nA for the ATSAML10 family. Actual system consumption also depends on clock configuration, enabled peripherals, analog activity, and the time the processor remains awake, so measure the complete operating mode required by your product.
Is ATSAML10D15A-YU suitable for a battery-powered sensor node?
Yes, the ATSAML10D15A-YU is suitable for battery-powered sensor nodes when its sleep current and analog capabilities meet the power budget. Its less-than-100 nA sleep specification, 12-bit ADC channels, and eight DMA channels support periodic, low-energy measurement. The final battery life also depends on sensor load, radio activity, and wake-up frequency.
What is the difference between ATSAML10D15A-YU and ATSAML10D16A-YU?
Both devices use the same low-power Arm Cortex-M23 product family, but their memory configurations differ, so firmware image size and board requirements must be reviewed before substitution. The exact flash and SRAM comparison should be taken from the manufacturer data sheets for each orderable part. Confirm peripheral availability and the complete pin configuration for the finished design.
When should I choose ATSAML10D15A-YU instead of another ATSAML10 variant?
Choose the ATSAML10D15A-YU when a 32 MHz Cortex-M23 design needs 32 KB of flash, 8 KB of SRAM, five 12-bit ADCs, a 10-bit DAC, and a compact 24-pin SSOP footprint. Select a larger-memory family member when firmware growth or working-memory demand exceeds those limits, or choose another variant when temperature, qualification, or package requirements differ.
What is the best drop-in replacement for ATSAML10D15A-YU?
The best same-footprint replacement identified for the ATSAML10D15A-YU is ATSAML10D15A-YUT, subject to confirming the packing format required by the assembly process. Both are 24-SSOP ATSAML10D15A configurations with a 32 MHz Cortex-M23 core, 32 KB flash, and 8 KB SRAM. Review the manufacturer pin table before production substitution.
Can ATSAML10D16A-YU replace ATSAML10D15A-YU?
The ATSAML10D16A-YU can serve as a redesign option within the same 24-SSOP ATSAML10 family when its memory and peripheral configuration satisfy the product requirements. It should not be treated as an automatic drop-in change because memory capacity and device configuration can affect firmware, timing, and certification. Compare both data sheets and re-run production test coverage.
Where to buy ATSAML10D15A-YU online?
ATSAML10D15A-YU can be ordered through the Request a Quote form on this page. The form supports exact-MPN inquiries, quantity requirements, and delivery planning, allowing the XAIPART team to confirm supply position and lot traceability. Request the current lead time and minimum order quantity with the quotation.
What is the price of ATSAML10D15A-YU?
The current commercial terms for ATSAML10D15A-YU are handled through the Request a Quote form on this page. Submit the required quantity, packing preference, delivery location, and target schedule to receive current pricing and availability confirmation. The form is the appropriate route for volume quotes and production scheduling.
What is the lead time for ATSAML10D15A-YU and is it in stock?
Current lead time, stock allocation, and minimum order quantity for ATSAML10D15A-YU should be confirmed through the Request a Quote form on this page. Provide the required quantity and target delivery date so scheduling can be evaluated against current component availability. Published distributor inventory totals can change without notice and should not be treated as a reservation.

엔지니어링 참조 데이터: ATSAML10D15A-YU — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the ATSAML10D15A-YU when the design needs a compact, low-power Cortex-M23 controller with 32 KB flash, 8 KB of SRAM, five 12-bit ADCs, a 10-bit DAC, and an ISO7816-capable peripheral set. It is particularly attractive for battery-operated sensor nodes, smart-card readers, capacitive-touch interfaces, and compact protocol controllers. The ATSAML10D15A-YUT is the closest configuration-equivalent choice when a different production packing format is needed. The higher-density ATSAML10D16A-YU, ATSAML10D17A-YU, and ATSAML10D18A-YU can serve same-family redesigns when their memory configurations match firmware growth, but each substitution requires a comparison of programming requirements, timing, peripherals, and validation coverage. For designs that require a larger package, different memory balance, or a different core architecture, evaluate another MCU rather than assuming that same-family naming guarantees a drop-in replacement.

대체품과의 비교

파라미터 이 제품 ATSAML10D15A-YUT ATSAML10D16A-YU ATSAML10D17A-YU ATSAML10D18A-YU
Package 24-SSOP 24-SSOP 24-SSOP 24-SSOP 24-SSOP
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
CPU Core Arm Cortex-M23, 32-bit Arm Cortex-M23, 32-bit Arm Cortex-M23, 32-bit Arm Cortex-M23, 32-bit Arm Cortex-M23, 32-bit
Maximum CPU Frequency 32 MHz 32 MHz 32 MHz 32 MHz 32 MHz

주요 차별점

  • Matches the ATSAML10D15A electrical configuration exactly (vs ATSAML10D15A-YUT)
  • Combines seven analog converters in one compact package (vs ATSAML10D16A-YU)
  • Eight DMA channels support autonomous peripheral data movement (vs ATSAML10D17A-YU)
  • Very low sleep-mode current for portable products (vs ATSAML10D18A-YU)

설계 노트

Design the 3.3 V supply path for the current required by the Cortex-M23 core, active analog conversion, and any attached load. Follow the Microchip recommended operating conditions and decoupling guidance for each supply pin. Place the prescribed bypass capacitors close to the package pins and keep the return current through the board's ground plane rather than through narrow signal traces.

Use the 24-SSOP footprint and verify pad dimensions against the current Microchip land pattern before routing. Separate analog inputs from switching or high-current signals, maintain the recommended analog-ground connection strategy, and provide short, direct paths for communications and debug functions. The SSOP lead pitch also makes careful solder-paste and assembly-process control important.

Do not select a higher-density ATSAML10 memory variant solely by the base device name. Flash capacity, SRAM, peripheral availability, and the associated orderable suffixes can change the firmware image, pin requirements, and validation scope. Compare the complete manufacturer data sheets and regenerate the production programming and test steps whenever the exact orderable MPN changes.

The five 12-bit ADCs and 10-bit DAC should be connected using the reference-ground and filtering methods shown in the Microchip application guidance. Place anti-alias or reconstruction components close to the relevant pins, avoid routing sensitive analog nets beneath digital activity, and evaluate the noise contribution of regulators and communication transceivers before establishing the measurement-resolution budget.

Although the device is characterized for low active-mode consumption, the total board temperature rise depends on the complete supply voltage, clock rate, duty cycle, ambient temperature, and PCB copper area. Validate the highest expected operating frequency and analog workload in the assembled enclosure, and keep the SSOP footprint clear of thermal barriers that would trap heat around the device.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer or distributor results. Review the Microchip product-page compliance documents and material-declaration records for the exact orderable MPN before release.

데이터 검증일: 2026-11-15 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

ATSAML10D15A-YU datasheet ATSAML10D15A-YU pinout ATSAML10D15A-YU datasheet pdf ATSAML10D15A-YU specifications ATSAML10D15A 24-SSOP pinout ATSAML10D15A-YU price ATSAML10D15A-YU stock ATSAML10D15A-YU equivalent ATSAML10D15A-YU replacement ATSAML10D15A-YU vs ATSAML10D15A-YUT Microchip ATSAML10D15A-YU ATSAML10D15A-YU footprint ATSAML10D15A low power sensor node ATSAML10D15A smart card interface

관련 부품 & 용어

Microchip Technology ATSAML10D15A-YU ATSAML10D15A-YUT ATSAML10D16A-YU ATSAML10D17A-YU ATSAML10D18A-YU Arm Cortex-M23 microcontroller 32-bit microcontroller Arm Cortex-M core embedded microcontroller semiconductor 24-SSOP SSOP package surface mount SMD program flash memory SRAM data EEPROM 12-bit ADC 10-bit DAC DMA channels SERCOM peripheral touch controller ISO7816 low-power mode RoHS REACH AEC-Q100
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기