ATTINY261A-MN - 20MHz AVR Microcontroller | Microchip
부품 번호: ATTINY261A-MN ✓ 활성ATTINY261A-MN 개요
What is an 8-bit AVR microcontroller? It is a compact RISC-based embedded controller that executes instructions from embedded Flash memory and uses general-purpose registers, timers, interrupts, and serial or analog peripherals to control electronic products. Within the embedded-product hierarchy, the ATTINY261A belongs to the AVR family, the 8-bit microcontroller class, and the broader power-management and embedded-control semiconductor category. Its picoPower implementation emphasizes efficient operation in small control systems.
Key device features include 2 KB of Flash organized as 1 K by 16 bits, 128 B of EEPROM, 128 B of internal SRAM, 32 working registers, and 16 general-purpose I/O lines. Peripherals described for this family include an 8-bit timer/counter with compare modes, PWM support, a prescaler, and a high-speed 8/10-bit timer/counter. The operating supply range is 1.8 V to 5.5 V, allowing operation across low-voltage and conventional 5 V embedded systems.
The ATTINY261A architecture combines an 8-bit AVR instruction set with Harvard-style separate program and data-memory organization and a reduced instruction cycle time. The 20 MHz operating capability provides practical headroom for event timing, digital control, and low-cost communication peripherals. Compared with larger AVR devices, its 2 KB Flash capacity favors compact firmware rather than graphical interfaces, large protocol stacks, or extensive data logging.
Typical uses include motor and valve control, lighting systems, small appliance controllers, industrial interface modules, and compact sensor nodes. Its 16 I/O lines, PWM-capable timers, and flexible 1.8 V to 5.5 V supply range make it useful when a board must combine control outputs with low-voltage sensing. Firmware and peripheral configuration should be selected with the 2 KB program-memory constraint in mind.
PCB planning must account for the 5 mm by 5 mm VQFN footprint, exposed thermal-pad requirements, and manufacturer land-pattern guidance. Place decoupling capacitors close to the supply pins and reserve adequate ground-plane area beneath the device to support both electrical return paths and thermal performance. Confirm final pad dimensions against the current manufacturer package drawing before fabrication.
This product page combines the manufacturer product information, package and memory details, drop-in family comparisons, and implementation guidance for engineers evaluating the ATTINY261A-MN in compact embedded systems.
드롭인 대체품: ATTINY261A-MN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATTINY261A-MN (동일 폼 팩터 및 풋프린트) — 차이점: EEPROM, Flash Memory, Timer/Counter, General-Purpose I/O Lines, General-Purpose Working Registers.
ATTINY261A-SU
✅ 드롭인가격 문의
데이터시트 보기 →ATTINY461A-SU
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ATTINY861A-SU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATTINY261A-MN 최대 정격 & 전기적 특성
| Product Type | 8-bit AVR RISC-based microcontroller |
| Architecture | AVR enhanced RISC |
| Technology | picoPower |
| 최대 클록 주파수 | 20 MHz |
| Flash Memory | 2 KB (1 K x 16 bits) |
| EEPROM | 128 B |
| Internal SRAM | 128 B |
| General-Purpose I/O Lines | 16 |
| General-Purpose Working Registers | 32 |
| 동작 공급 전압 | 1.8 V to 5.5 V |
| Nominal Supply Options | 2.5 V, 3.3 V, and 5 V |
| Timer/Counter | 8-bit with compare modes, PWM, and prescaler |
| High-Speed Timer/Counter | 8/10-bit |
| Instruction Set | 123 powerful AVR instructions |
| 패키지 | 32-VQFN, 5 mm x 5 mm |
| 실장 유형 | Surface mount |
| Program Memory Type | In-system self-programmable Flash |
ATTINY261A-MN 32-vqfn, 5 mm x 5 mm 핀 구성 가이드
ATTINY261A-MN(32-vqfn, 5 mm x 5 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATTINY261A-MN.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATTINY261A-MN 적합 용도: 6 애플리케이션s: Compact Motor Control, LED Lighting Controller, Small Appliance Controller, Industrial Valve and Relay Interface, Battery-Powered Sensor Interface, Embedded Control and Signal Interface.
Compact Motor Control
The ATTINY261A-MN fits compact motor-control and position-control designs because its 16 general-purpose I/O lines can support control signals, switches, and sensors, while its timer resources include an 8-bit timer/counter with compare modes, PWM, and a prescaler. At up to 20 MHz, the microcontroller can execute timing logic and closed-loop control routines without a larger processor. Place it beside a suitable gate driver or H-bridge, connect the motor position sensor to an available timer or ADC-capable peripheral, and preserve separate analog and digital grounding. The 2 KB Flash limit makes concise fixed-point control code preferable to feature-heavy motion algorithms.
추천
LED Lighting Controller
The ATTINY261A-MN is appropriate for programmable LED lighting because its PWM-capable timer/counter supports dimming and patterned output while 16 I/O lines provide room for mode buttons, indicators, and fault signals. The device operates from 1.8 V to 5.5 V, allowing it to share a regulated rail with compatible LED-driver circuitry. Implement current limiting and constant-current conversion outside the MCU, and synchronize dimming updates to the timer rather than relying on blocking delays. Its 2 KB Flash is sufficient for compact lighting tables, fade sequences, and basic schedules, but large animation libraries may require a higher-memory controller.
추천
Small Appliance Controller
The ATTINY261A-MN works well in small appliances where a compact controller manages buttons, relays, heaters, fans, and status indicators. Its 128 B of SRAM and 128 B of EEPROM provide enough working space for compact state machines and retained settings, while 16 I/O lines offer flexible peripheral assignment. The 20 MHz clock supports responsive debouncing and timing logic, and the 1.8 V to 5.5 V operating range permits integration with several common supply arrangements. Use appropriate flyback protection for inductive loads and keep mains-connected switching circuitry isolated from the low-voltage controller section.
추천
Industrial Valve and Relay Interface
The ATTINY261A-MN can act as the low-power controller in a compact valve, relay, or actuator interface module. Sixteen I/O lines allow a mixture of command outputs and status inputs, while the 8-bit and 8/10-bit timer resources support pulse timing, debounce intervals, and periodic monitoring. Operating down to 1.8 V provides flexibility when the interface electronics use a regulated low-voltage rail. Separate field-side drivers from logic ground where isolation is required, select components for the coil voltage and switching current, and validate timing behavior across the complete operating-temperature range.
추천
Battery-Powered Sensor Interface
The ATTINY261A-MN is useful in a small sensor-interface node because its picoPower AVR architecture targets efficient embedded operation and its 1.8 V to 5.5 V supply range accommodates low-energy rails. Sixteen I/O lines can support digital sensors, interrupt inputs, and status indicators without an external I/O expander. The 128 B of SRAM is suitable for compact sampling and filtering routines, while EEPROM can retain calibration flags or configuration values. Avoid continuous high-frequency clocking when the application permits, use the MCU sleep modes appropriately, and confirm timer and peripheral behavior at the lowest operating voltage.
추천
Embedded Control and Signal Interface
The ATTINY261A-MN supports compact embedded signal-interface products that coordinate switches, inputs, timing, and status outputs. Its 20 MHz AVR RISC core can process protocol framing or control logic, while 16 I/O lines and multiple timer resources distribute timing tasks across dedicated peripherals. The 32-VQFN, 5 mm by 5 mm package minimizes board area in modules with limited space. Keep firmware within the 2 KB Flash budget, use interrupt-driven transfers where appropriate, and route externally exposed signals through protection networks. Review every alternate-function assignment against the manufacturer pin-description table before finalizing the PCB.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATTINY261A-MN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATTINY261A-SU | ATTINY461A-SU | ATTINY861A-SU |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) |
| Architecture | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 2 KB | 2 KB | 4 KB | 8 KB |
| EEPROM | 128 B | 128 B | 128 B | 128 B |
| Internal SRAM | 128 B | 128 B | 128 B | 128 B |
| Operating Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| General-Purpose I/O Lines | 16 | 16 | 16 | 16 |
| Timer Resources | 8-bit timer/counter and 8/10-bit high-speed timer/counter | 8-bit timer/counter and 8/10-bit high-speed timer/counter | 8-bit timer/counter and 8/10-bit high-speed timer/counter | 8-bit timer/counter and 8/10-bit high-speed timer/counter |
주요 차별점
- Lower Flash requirement for compact control firmware (vs ATTINY861A-SU)
- Intermediate firmware capacity option (vs ATTINY461A-SU)
- Direct family-device alignment for related controls (vs ATTINY261A-SU)
설계 노트
Use the exact 32-VQFN land pattern from the manufacturer package drawing and verify pin-one orientation against the PCB footprint. Place the required bypass capacitors next to the supply and ground pins, maintain short return paths, and provide thermal-via structures beneath the exposed pad as recommended. The 5 mm by 5 mm package is compact, but incorrect pad geometry or exposed-pad connection can prevent reliable assembly and heat transfer.
Design the supply rail for the selected operating point within the 1.8 V to 5.5 V device range. Check input, output, and I/O voltage limits against the datasheet rather than assuming every pin is 5 V tolerant. Decouple the MCU locally and keep switching-regulator and motor-driver switching nodes away from sensitive input traces. Where a 3.3 V rail powers both the MCU and peripherals, confirm that each peripheral meets the same brownout and supply constraints.
Account for the ATTINY261A-MN’s 2 KB Flash limit before committing to firmware architecture. Excess code size can prevent programming or leave insufficient room for boot and configuration routines. Compile with the exact device definition in the toolchain, verify the selected clock and fuse settings, and include a recovery path for programming. Do not substitute a higher-memory family member without reviewing timer mappings, peripheral availability, and application code assumptions.
For designs using the timer inputs, external sensor lines, or communication signals, assign pins from the manufacturer’s alternate-function tables before routing the PCB. Keep oscillator, reset, and sensitive analog connections short and follow the reference layout. If the board also contains relays, motors, or LEDs, separate their return currents from the MCU ground path where possible and place protection components close to the connector or driver stage.
규정 준수 정보
The current Microchip Technology product information should be used for declarations concerning RoHS, REACH, lead-free status, halogen-free status, conflict minerals, and automotive qualification.