ATXMEGA8E5-M4N - 32MHz 8KB AVR Microcontroller | Microchip
부품 번호: ATXMEGA8E5-M4N ✓ 활성ATXMEGA8E5-M4N 개요
An 8-bit microcontroller is a compact embedded-processing device built around a central processing unit, memory, and programmable peripherals. Within the Microchip product hierarchy, the ATxmega8E5 belongs to the AVR XMEGA family of 8/16-bit microcontrollers. This family combines a high-performance, low-power AVR enhanced RISC architecture with event handling, mixed-signal control, communications, and timing resources suited to compact embedded systems.
The ATXMEGA8E5-M4N includes an eight-channel event system and a programmable multi-level interrupt mechanism according to the Microchip product-page summary. Its 8 KB of ISP flash supports in-system programming, while read-while-write operation can permit programming while the application remains active. Separate boot-code storage provides 2 KB for startup code, and the combination of 1 KB SRAM and 512 bytes of EEPROM supports working state and retained configuration data.
The device runs at a maximum frequency of 32 MHz. This performance level is useful for protocol handling, timing-intensive control, and connected embedded functions without moving the design to a larger processor. Its 1.6 V to 3.6 V supply range permits use with common 3.3 V system rails, while the 105 °C maximum operating temperature provides an extended temperature option for demanding industrial equipment.
Typical uses include compact industrial controllers, IoT sensor nodes, building-control endpoints, low-power data acquisition units, communication modules, and small motor or actuator controllers. The small 4 mm by 4 mm UQFN package supports space-constrained designs, although its fine pitch and exposed thermal pad require careful PCB assembly and thermal management.
For implementation, place the decoupling capacitors close to the supply and ground pins, follow the manufacturer's recommended external-component arrangement, and provide programming access through the supported AVR interface. Verify the complete 32-pin signal map against the ATxmega8E5 datasheet before assigning alternate functions or designing a new footprint. Confirm that adjacent components, communication transceivers, and regulators meet the device's voltage and timing requirements.
This product page combines the Microchip family specifications, exact ATXMEGA8E5-M4N order-code details, package information, and engineering-oriented design guidance. It also distinguishes the specified 32-UQFN device from package variants that cannot replace it directly, helping designers assess footprint compatibility before committing a PCB or production BOM.
드롭인 대체품: ATXMEGA8E5-M4N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATXMEGA8E5-M4N (동일 폼 팩터 및 풋프린트) — 차이점: Package, EEPROM, Product Type, SRAM, Core Architecture.
ATXMEGA8E5-MU
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ATXMEGA8E5-M4N 최대 정격 & 전기적 특성
| Microcontroller Family | AVR XMEGA |
| Architecture | 8/16-bit AVR enhanced RISC |
| Maximum CPU Frequency | 32 MHz |
| Program Flash Memory | 8 KB |
| Boot Code Section | 2 KB |
| EEPROM | 512 bytes |
| SRAM | 1 KB |
| Flash Programming | In-system programming |
| Read-While-Write Flash | Supported |
| Event System | 8 channels |
| Operating Voltage Range | 1.6 V to 3.6 V |
| Maximum Operating Temperature | 105 °C |
| 패키지 | 32-UQFN, 4 mm x 4 mm |
| 실장 유형 | Surface mount |
| Product Environmental Designation | Green |
| Programmable Interrupt Levels | Multi-level |
| 핀 수 | 32 pins |
ATXMEGA8E5-M4N 32-uqfn, 4 mm x 4 mm 핀 구성 가이드
ATXMEGA8E5-M4N(32-uqfn, 4 mm x 4 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATXMEGA8E5-M4N.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATXMEGA8E5-M4N 적합 용도: 6 애플리케이션s: Industrial Sensor and Control Node, IoT Edge Sensor Node, Building Automation Endpoint, Communication Protocol Converter, Compact Data Acquisition Module, Battery-Powered Embedded Controller.
Industrial Sensor and Control Node
The ATXMEGA8E5-M4N fits compact industrial sensing and control nodes that process several digital or timer-driven channels while maintaining a small board footprint. Its 32 MHz maximum clock supports responsive protocol handling and control logic, while the eight-channel event system can coordinate sensors and outputs without relying on constant polling. The 1 KB SRAM and 512-byte EEPROM are adequate for modest configuration and working data, but designers should budget memory before adding history logging. Operating from 1.6 V to 3.6 V simplifies integration with regulated low-voltage rails, and the 105 °C rating supports extended-temperature equipment when the surrounding components are also qualified.
추천
IoT Edge Sensor Node
The ATXMEGA8E5-M4N can serve as the local control MCU in a small IoT sensor node that gathers measurements, performs threshold decisions, and prepares data for a communications module. Its 32 MHz processing rate provides headroom for lightweight digital filtering and serial protocols, while the eight-channel event system helps link timers, external inputs, and communication activity. The 8 KB program memory is suitable for compact firmware, and the 2 KB boot section can hold initialization or recovery routines. A 3.3 V system architecture fits the stated 1.6 V to 3.6 V operating range, provided the radio and sensors remain within compatible voltage limits.
추천
Building Automation Endpoint
ATXMEGA8E5-M4N is appropriate for compact building-automation endpoints that coordinate switches, sensors, timing functions, and a low-speed communications interface. Its event system can link periodic measurements with asynchronous inputs, reducing the processing burden associated with simple polling architectures. The 32 MHz clock gives adequate margin for protocol handling and control logic, while 512 bytes of EEPROM can retain calibration values, device addresses, or configuration flags. The 4 mm by 4 mm 32-UQFN package helps reduce terminal-block or DIN-rail controller size. Firmware and SRAM requirements must be checked carefully because 8 KB and 1 KB are modest for complex gateway functions.
추천
Communication Protocol Converter
The ATXMEGA8E5-M4N can support a small protocol-conversion or interface-control product when the design requires deterministic event timing and moderate protocol-processing load. The eight-channel event system is useful for coordinating serial transfers, timer events, and control signals, while the 32 MHz CPU provides processing margin for framing and state management. Its 1 KB SRAM must be sized against transmit buffers, receive queues, and the communication stack, and the 8 KB flash limit favors compact protocols or a dedicated companion transceiver. The 1.6 V to 3.6 V range permits integration into low-voltage interface boards, subject to the external transceiver requirements.
추천
Compact Data Acquisition Module
ATXMEGA8E5-M4N is suitable for a compact data-acquisition module that samples digital inputs, timestamps events, and forwards selected measurements over a serial link. The 32 MHz clock and programmable multi-level interrupt structure support time-sensitive acquisition routines, while the eight-channel event system can coordinate timers and peripheral events. The 1 KB SRAM is the principal design constraint for buffering, so continuous logging generally requires external storage or a higher-memory MCU. The device's 1.6 V to 3.6 V operating range supports low-voltage analog and sensor front ends, and the 105 °C maximum temperature can assist in extended-temperature industrial installations.
추천
Battery-Powered Embedded Controller
The ATXMEGA8E5-M4N can be used in a battery-powered embedded controller when its low-power operating modes and event-driven architecture align with the duty cycle. Sleeping between infrequent measurements can reduce energy consumption, while the event system allows timers and external activity to wake the device selectively. The 1.6 V minimum operating voltage is useful for direct connection to suitably regulated low-voltage power systems, while 1 KB SRAM limits simultaneous data buffering. Firmware should use the 2 KB boot-code section for initialization rather than large application functions, and the complete power path must be sized for peak processing current rather than average sleep current.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATXMEGA8E5-M4N — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Brand | Microchip Technology |
| Package | 32-UQFN, 4 mm x 4 mm |
| Maximum CPU Frequency | 32 MHz |
| Program Flash Memory | 8 KB |
| Boot Code Section | 2 KB |
| EEPROM | 512 bytes |
| SRAM | 1 KB |
| Operating Voltage Range | 1.6 V to 3.6 V |
| Maximum Operating Temperature | 105 °C |
| Event System | 8 channels |
주요 차별점
- Compact 32-UQFN implementation (vs ATXMEGA64A1-CUR)
- Event-driven control architecture (vs ATXMEGA64A1-CUR)
- Extended-temperature order configuration (vs ATXMEGA8E5-M4N)
설계 노트
Use the complete 32-UQFN land pattern from the manufacturer package drawing, including the exposed thermal-pad connection and its via arrangement. Confirm the terminal definitions against the ATxmega8E5 pin-description table because alternate functions and reserved positions must not be assigned from memory. Place the required supply-decoupling capacitor immediately beside the power and ground terminals, preserve a short return path for high-current transitions, and route programming signals so they remain accessible without creating long antenna-like traces around the MCU.
Design the supply for the ATXMEGA8E5-M4N's 1.6 V to 3.6 V operating range and the highest applicable transient current, not merely the average active current. A 3.3 V rail is within the device's range, but the regulator must also tolerate the voltage tolerance of the selected power source and startup behavior of the connected loads. Check the maximum clock, analog peripherals, communications interface, and output loads together. Place bulk energy storage near the rail origin and local ceramic decoupling beside the package to limit supply disturbance during instruction execution and peripheral activity.
The 32-UQFN package requires deliberate heat spreading because its small body limits the available surface area. Connect the exposed pad to a properly designed ground or thermal plane, use multiple thermal vias when permitted by the manufacturer layout, and avoid placing heat-generating regulators or power components directly beneath the MCU. The stated 105 °C maximum operating temperature does not remove the need for junction-temperature margin. Validate the final enclosure, ambient temperature, copper area, via count, switching loss, and neighboring heat sources under worst-case operating conditions.
Do not substitute another ATxmega8E5 package suffix without checking the physical footprint and pin mapping. Likewise, do not treat a functionally similar AVR device as a drop-in replacement when its memory organization, voltage limits, peripheral pins, or boot behavior differs. A valid substitution review must cover the 32-UQFN 4 mm by 4 mm footprint, all 32 positions, power and ground locations, programming signals, exposed-pad requirements, clock options, and peripheral assignments. Confirm production firmware and boot-loader compatibility before releasing an alternate part number.
규정 준수 정보
The distributor listing describes the ATXMEGA8E5-M4N as Green, but no specific RoHS, REACH, halogen-free, conflict-minerals, or automotive-qualification declaration was identified. Confirm compliance documents for the exact order code before procurement.