DG408DYZ - 8:1 CMOS Analog Multiplexer | Renesas Electronics
부품 번호: DG408DYZ ✓ 활성DG408DYZ 개요
An analog multiplexer is a switch matrix that routes one of several signal sources onto a shared output path. The DG408 belongs to the analog switch and multiplexer hierarchy, where its CMOS construction supports low power consumption and wide input voltage range compared with relay-based selectors. Its 8:1 configuration gives an eight-channel instrument, data-acquisition system, or automated test fixture a compact way to share one analog front end among multiple sources.
The device uses three address lines for binary channel selection and an active-low or active-high ENABLE control according to the manufacturer logic specification. A TTL/CMOS-compatible decoder accepts standard logic levels, while the internal voltage reference establishes stable switching thresholds across supply conditions. Because the analog paths are bidirectional, the same DG408DYZ can be used to route a common signal toward one of eight external terminals as well as to select an incoming source.
The DG408 series is documented as a drop-in replacement for the popular DG508A and DG509A families. Renesas also positions the DG408 and DG409 as pin-compatible single-ended 8-channel and differential 4-channel options respectively. The industrial DG408DYZ grade is suited to test and measurement, data acquisition, signal routing, control systems, and industrial interface boards where a SOIC footprint and deterministic logic decoding are preferred.
Bidirectional operation simplifies PCB routing because the channel pins are not restricted to a dedicated input or output role. Nevertheless, keep all external analog nodes within the absolute maximum ratings listed in the manufacturer datasheet, and use input protection networks when signals can exceed the selected supply rails. Account for the 100 ohm maximum on-resistance when calculating source impedance, especially when driving high-impedance sensors or precision measurement chains.
This page combines the manufacturer family information with distributor specifications, package details, equivalent-device references, and practical design guidance. It also identifies where a drop-in comparison should focus on package geometry, logic decoding, channel count, on-resistance, signal range, and temperature grade rather than on the DG408 name alone.
드롭인 대체품: DG408DYZ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DG408DYZ (동일 폼 팩터 및 풋프린트) — 차이점: Package, On-Resistance, Channel Matching, Multiplexer Configuration, Switch Architecture.
DG408DY+
✅ 드롭인가격 문의
데이터시트 보기 →DG408DY+
✅ 드롭인가격 문의
데이터시트 보기 →DG408DY+
✅ 드롭인가격 문의
데이터시트 보기 →DG408DY+
✅ 드롭인가격 문의
데이터시트 보기 →TSX-310
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG408DYZ 사양
| Multiplexer Configuration | Single 8:1 |
| Number of Circuits | 1 circuit |
| Number of Channels | 8 channels |
| On-Resistance | 100 ohm maximum |
| Analog Signal Direction | Bidirectional |
| Switch Architecture | Eight analog switches with TTL/CMOS-compatible digital decode |
| Process Technology | CMOS |
| Logic Threshold Reference | Internal voltage reference |
| Device Selection Control | ENABLE input |
| 패키지 | 16-pin SOIC |
| 실장 유형 | Surface mount |
| 동작 온도 범위 | -40 C to +85 C |
| Industrial Grade | Yes |
| Legacy Compatibility | Drop-in replacement for DG508A and DG509A series devices |
DG408DYZ 16-pin soic 핀 구성 가이드
DG408DYZ(16-pin soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: DG408DYZ.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DG408DYZ 적합 용도: 6 애플리케이션s: Multichannel Data Acquisition, Automated Test Equipment Signal Routing, Industrial Sensor Interface, Programmable Signal Conditioning, Battery-Powered Monitoring Equipment, Communication and RF Signal Routing.
Multichannel Data Acquisition
The DG408DYZ fits a data-acquisition front end that selects among eight analog sources with one shared amplifier chain. Its bidirectional analog paths allow either source selection or common-signal distribution, while the TTL/CMOS-compatible decoder and ENABLE input can be driven directly by a microcontroller or FPGA. The published 100 ohm maximum on-resistance must be included in the source-impedance budget, especially when measuring high-impedance sensors. Use the manufacturer pin table to assign tracks and confirm the allowed signal range before routing external inputs.
추천
Automated Test Equipment Signal Routing
In automated test equipment, the DG408DYZ can route one of eight test points, excitation nodes, or instrument channels through a common fixture interface. The ENABLE input allows a controller to disable the mux during fixture transitions, while the binary decoder selects the active path. Because the analog channels are bidirectional, the same device can also distribute a reference or stimulus to one selected branch. Maintain consistent impedance across all eight routes so switching does not create measurement errors, and include protection ahead of externally accessible nodes.
추천
Industrial Sensor Interface
The DG408DYZ can consolidate eight analog sensor outputs onto a single controller input, reducing the number of separate front-end channels in industrial monitoring equipment. Its -40 C to +85 C industrial temperature range suits equipment exposed to variable ambient conditions, and the TTL/CMOS-compatible control inputs simplify interfacing with standard digital logic. The 100 ohm maximum on-resistance can become significant with high-impedance sensors, so place a low-input-impedance buffer after the mux when full-scale accuracy is required. Keep sensor returns and mux ground paths within the device's rated common-mode limits.
추천
Programmable Signal Conditioning
A programmable signal-conditioning system can use the DG408DYZ to route different amplifier, filter, or reference taps into a common processing chain. This approach makes the board flexible without requiring a separate connector for every source and allows software to configure the channel address through the digital decoder. Bidirectional operation supports feedback-style measurements as well as source selection. The mux's 100 ohm maximum on-resistance introduces channel-dependent loading unless all branches are matched, so characterize the complete network and place any precision amplifier immediately after the selected node.
추천
Battery-Powered Monitoring Equipment
Portable monitoring equipment can use the DG408DYZ to reduce the number of analog inputs handled by a low-power controller. The CMOS multiplexer is designed for low-power operation, and the ENABLE control lets firmware disable the device when no channel needs to be observed. The shared-output topology also reduces board area compared with eight separate signal paths. Verify supply-current behavior and analog signal limits in the manufacturer datasheet for the intended battery voltage, and use a buffered output when the source impedance approaches the mux's 100 ohm maximum on-resistance.
추천
Communication and RF Signal Routing
The DG408DYZ can select low-level analog branches in communication equipment, instrumentation, or controlled test paths where a compact SOIC multiplexer is preferred. Bidirectional channels make it possible to route a common signal toward one of eight destinations as well as select a source for a receiver chain. The 100 ohm maximum on-resistance is modest for precision measurement but must be checked against the termination and noise requirements of the application. Keep sensitive traces away from digital address and ENABLE lines, and confirm the permitted signal swing in the manufacturer datasheet.
추천
추천 제품 요약
엔지니어링 참조 데이터: DG408DYZ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DG408DY | DG408DY+ | DG408DY | DG408DY+ | TSX-310 |
|---|---|---|---|---|---|---|
| Manufacturer | Renesas Electronics | Renesas Electronics | Renesas Electronics | Vishay Intertechnology | Vishay Intertechnology | Texas Instruments |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Multiplexer Configuration | Single 8:1 | Single 8:1 | Single 8:1 | 8-channel | 8-channel | 8:1 analog multiplexer |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Maximum On-Resistance | 100 ohm | 100 ohm | 100 ohm | 100 ohm class | 100 ohm class | Approximately 80 ohm |
| Analog Channel Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
| Operating Temperature Range | -40 C to +85 C | Industrial grade | Industrial grade | Industrial grade | Industrial grade | -40 C to +85 C |
| Logic Compatibility | TTL/CMOS-compatible decode with ENABLE input | TTL/CMOS-compatible decode with ENABLE input | TTL/CMOS-compatible decode with ENABLE input | TTL/CMOS-compatible decode | TTL/CMOS-compatible decode | TTL/CMOS-compatible control |
| Legacy Replacement Target | DG508A and DG509A series | DG508A/DG509A family | DG508A/DG509A family | High-performance CMOS mux family | High-performance CMOS mux family | 8-channel analog multiplexer |
주요 차별점
- Single-ended 8-channel multiplexing with bidirectional analog paths (vs TSX-310)
- Documented compatibility with established DG508A and DG509A designs (vs TSX-310)
- Internal threshold reference and ENABLE control in the same 16-pin SOIC (vs MAX4634)
설계 노트
Treat the mux on-resistance as part of the source impedance. At the 100 ohm maximum, attenuation and thermal noise become more significant when the selected branch drives a high-impedance amplifier. Place a low-input-impedance buffer after the mux when the sensor impedance is high, and keep channel routing geometry similar so switching does not create gain or phase discontinuities between channels.
Route the eight analog paths as compact, mutually separated traces and connect the multiplexer ground reference to the quiet analog ground region. Keep the address and ENABLE traces away from sensitive analog nets. Because the channels are bidirectional, provide input protection at external connectors and ensure every external node remains inside the absolute maximum ratings in the manufacturer datasheet.
Do not assume that every part labeled DG408 is interchangeable solely from its multiplex ratio. Check the 16-pin SOIC pin map, supply-voltage range, ENABLE polarity, address convention, analog signal range, and switching specifications. Also verify the exact orderable suffix and packing method, because tape-and-reel, tube, and temperature-grade order codes can describe different purchasing configurations of the same device family.
규정 준수 정보
The industrial temperature grade is documented, but no specific RoHS, REACH, halogen-free, or conflict-minerals declaration was identified in the available manufacturer and distributor records.