DSPIC33EP64MC506-E/PT - 16-bit DSC 64KB Flash 60MHz | Microchip
부품 번호: DSPIC33EP64MC506-E/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $7.2 | $7.20 |
| 10 | $6.55 | $65.50 |
| 100 | $5.9 | $590.00 |
| 500 | $5.35 | $2,675.00 |
| 1,000 | $4.85 | $4,850.00 |
DSPIC33EP64MC506-E/PT 개요
A digital signal controller combines the compute throughput of a digital signal processor with the peripheral integration and deterministic control flow of a microcontroller. Within the power management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33E family a leading choice for closed-loop motor control, digital power conversion, and sensor signal processing where a single chip must execute control loops, filtering mathematics, and communication tasks simultaneously.
Key features include motor-control PWM (MCPWM) outputs with complementary modes and dead-time insertion, a quadrature encoder interface (QEI) for position feedback, a CAN 2.0B controller for industrial networking, three on-chip operational amplifiers, and four comparators. The 16-channel 10/12-bit ADC supports high-speed sampling of phase currents and bus voltages for field-oriented control (FOC) algorithms.
The dsPIC33E core implements an enhanced Harvard architecture with DSP instructions (MAC, DSP multiply-accumulate), a 16x16 multiplier, and 40-bit accumulators, enabling single-cycle MAC operations critical for real-time current-loop bandwidth. The CMOS process delivers low active power with 3.0V to 3.6V supply operation.
Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, servo amplifiers, AC-DC and DC-DC digital power supplies, and industrial automation nodes using CAN bus. The 53 general-purpose I/O pins and 16-channel ADC make it well matched to multi-motor boards and sensor-dense systems.
Design consideration: budget the VCAP core-regulator capacitor exactly per the manufacturer datasheet; omitting or misplacing it is the most common cause of startup instability on the dsPIC33E family.
This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: DSPIC33EP64MC506-E/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DSPIC33EP64MC506-E/PT (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature, Package, Timers, Core, Core Architecture.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
DSPIC33EP64MC506-I/PT
✅ 드롭인✓ 재고 있음
$4.11 / 개
데이터시트 보기 →DSPIC33EP256MC506-I/PT
✅ 드롭인✓ 재고 있음
$5.95 / 개
데이터시트 보기 →DSPIC33EP128MC506-I/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DSPIC33EP32MC506-I/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DSPIC33EP64GS506-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DSPIC33EP64MC506-E/PT 최대 정격 & 전기적 특성
| Core | dsPIC33E, 16-bit DSC |
| Core Clock Speed | 60 MHz |
| Flash Program Memory | 64 KB (22K x 24) |
| SRAM Data Memory | 8 KB |
| 공급 전압 | 3 V to 3.6 V |
| I/O Pins | 53 general-purpose I/O |
| ADC | 16-channel, 10/12-bit |
| Op Amps | 3 on-chip |
| Comparators | 4 |
| PWM | Motor Control PWM (MCPWM) |
| Quadrature Encoder Interface | Yes (QEI) |
| CAN | CAN 2.0B controller |
| Timers | 5 timers |
| 동작 온도 | -40C to +125C (E, extended) |
| 패키지 | 64-pin TQFP (10x10 mm), 0.5 mm pitch (PT) |
| 실장 유형 | Surface Mount |
| Process Technology | CMOS |
| Life Cycle Stage | Active |
DSPIC33EP64MC506-E/PT 64-pin tqfp (10x10 mm), 0.5 mm pitch (pt) 핀 구성 가이드
DSPIC33EP64MC506-E/PT(64-pin tqfp (10x10 mm), 0.5 mm pitch (pt) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: DSPIC33EP64MC506-E/PT.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DSPIC33EP64MC506-E/PT 적합 용도: 6 애플리케이션s: BLDC / PMSM Motor Drives, Digital Power Conversion (SMPS), Industrial Automation / CAN Nodes, Servo Amplifiers and Motion Control, Sensor Signal Processing, Automotive-Adjacent and Heavy Equipment Controllers.
BLDC / PMSM Motor Drives
The DSPIC33EP64MC506-E/PT is purpose-built for field-oriented control (FOC) of brushless DC and permanent-magnet synchronous motors. Its motor-control PWM module generates complementary outputs with programmable dead-time for three-phase bridges, the QEI decodes encoder position feedback directly, and the 16-channel 10/12-bit ADC synchronously samples phase currents and DC bus voltage. With the 60 MHz DSP core executing single-cycle MAC operations, current loops can close at PWM frequency while maintaining sensorless or sensited algorithms. The three on-chip op amps amplify low-side shunt signals, reducing external BOM cost. Extended -40C to +125C operation suits drive units in industrial cabinets and outdoor equipment.
추천
Digital Power Conversion (SMPS)
For digital switch-mode power supplies - AC-DC front ends, LLC converters, and high-density DC-DC bricks - the dsPIC33EP64MC506 executes voltage- and current-loop compensation digitally at 60 MHz. Although the GS506 variant is the SMPS-specialized sibling, the MC506's MCPWM module with high-resolution duty control and its fast comparators support peak-current-mode and burst-mode schemes. The 12-bit ADC monitors output voltage and input conditions for power-good sequencing and fault shutdown via hardware limits. The CAN interface enables PMBus-style supervisory control in rack power systems. For a pure digital-power BOM consolidation, designers may cross-consider DSPIC33EP64GS506-I/PT on the same 64-TQFP footprint.
추천
Industrial Automation / CAN Nodes
In factory automation, the DSPIC33EP64MC506-E/PT serves as an intelligent actuator or sensor node: the CAN 2.0B controller handles deterministic industrial networking at up to 1 Mbps, while 53 general-purpose I/O with peripheral remapping lets one chip drive relays, read quadrature encoders, and sequence I/O without external glue logic. The extended temperature rating permits mounting inside motor housings and switchgear. The DSP engine filters analog signals (vibration, current signatures) for predictive maintenance analytics at the edge, reducing upward bandwidth demands on the CAN backbone.
추천
Servo Amplifiers and Motion Control
Servo drives require tight coordination of position, velocity, and current cascades; the DSPIC33EP64MC506-E/PT closes these cascades on one die. The QEI module interfaces with incremental encoders for high-resolution position feedback, while the MCPWM module drives the power stage with dead-time-protected complementary outputs. The 60 MHz core's DSP instruction set implements PI/PID and notch filters for mechanical resonance suppression in software. With 3 op amps and 4 comparators on-chip, analog front-end count is minimized, and the extended -40C to +125C rating covers drive enclosures without forced-air cooling assumptions.
추천
Sensor Signal Processing
The DSPIC33EP64MC506-E/PT excels as an embedded DSP front end for analog sensors. Its 16-channel 10/12-bit ADC with simultaneous multi-channel scanning captures arrays of strain, pressure, or current sensors, while the on-chip op amps provide programmable-gain amplification ahead of conversion. The 40-bit accumulator DSP engine executes FIR/IIR filtering, RMS computation, and FFT windows in real time at 60 MHz, enabling condition monitoring and measurement products without a separate DSP. The 64-pin TQFP provides 53 I/O, ample for multiplexed sensor banks, and the 8KB SRAM buffers waveform captures for CAN or UART upload.
추천
Automotive-Adjacent and Heavy Equipment Controllers
Heavy equipment and off-highway subsystem controllers benefit from the E-grade (-40C to +125C) temperature rating of the DSPIC33EP64MC506-E/PT, tolerating engine-bay and hydraulic-compartment temperatures that defeat industrial-grade parts. The CAN 2.0B interface integrates with vehicle J1939-style networks, the MCPWM drives hydraulic valves and DC motors, and the 12-bit ADC reads pressure and temperature transducers. Robust 5V-tolerant-style I/O design practices with external conditioning let the 3.3V DSC bridge legacy 24V industrial signaling through optocouplers or level shifters on a single-controller PCB.
추천
추천 제품 요약
엔지니어링 참조 데이터: DSPIC33EP64MC506-E/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DSPIC33EP64MC506-I/PT | DSPIC33EP256MC506-I/PT | DSPIC33EP128MC506-I/PT | DSPIC33EP32MC506-I/PT | DSPIC33EP64GS506-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Program Memory | 64 KB | 64 KB | 256 KB | 128 KB | 32 KB | 64 KB |
| Core Speed | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz |
| Temperature Range | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) |
| Peripheral Focus | MCPWM + QEI, motor control, 3 op amps, 4 comparators, CAN | MCPWM + QEI, motor control, CAN - identical | MCPWM + QEI, motor control, CAN - identical | MCPWM + QEI, motor control, CAN - identical | MCPWM + QEI, motor control, CAN - identical | SMPS/digital-power PWM set (differs) |
| Lifecycle Status | Active | Active | Active | Active | Active | Active |
주요 차별점
- Extended temperature rating for harsh enclosures (vs DSPIC33EP64MC506-I/PT)
- Right-sized 64KB Flash minimizes cost (vs DSPIC33EP256MC506-I/PT)
- Motor-control peripheral integration reduces BOM (vs DSPIC33EP64GS506-I/PT)
설계 노트
The dsPIC33EP64MC506 requires a 3.0V-3.6V supply with an on-chip core regulator decoupled at the VCAP pin. Estimated: a typical 3.3V rail with 100 mA average controller current implies ~0.33W device dissipation - modest, but supply ripple should be kept low for ADC accuracy. Use a dedicated 3.3V LDO or filtered buck output for the analog supply (AVDD) with an RC or ferrite filter from the digital rail to preserve the 12-bit ADC effective number of bits.
For motor-control layouts on the 64-TQFP, keep the MCPWM gate-driver traces short and routed away from the QEI encoder inputs to prevent PWM switching edges from corrupting position counts. Place 0.1uF decoupling capacitors at every VDD pin within 2-3 mm, and one bulk 10uF near the controller. Tie AVSS to a quiet analog ground island connected to the digital ground at a single point under the ADC.
The most common dsPIC33E startup failure is omitting or undersizing the VCAP core-regulator capacitor specified in the Microchip datasheet - symptoms include intermittent resets at high temperature. Also note that MCLR requires a proper pull-up and programmer connector for in-circuit debugging with PICkit/ICD tools; omitting this access forces socketed production programming.
규정 준수 정보
RoHS compliant and lead-free per Mouser/DigiKey distributor listings for the /PT TQFP tray package. REACH and halogen-free status should be confirmed against Microchip product compliance documentation. Not AEC-Q100 automotive qualified (note: Octopart comparison lists the dsPIC33EP series as carrying AEC-Q100-related automotive references for some variants - verify with Microchip for automotive builds).
