DSPIC33FJ64GP306-I/PT - 16-bit DSC 40MIPS 64KB Flash | Microchip
부품 번호: DSPIC33FJ64GP306-I/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $5.52 | $5.52 |
| 10 | $5.1 | $51.00 |
| 100 | $4.72 | $472.00 |
| 500 | $4.35 | $2,175.00 |
| 1,000 | $4.05 | $4,050.00 |
DSPIC33FJ64GP306-I/PT 개요
A Digital Signal Controller blends the control capabilities of a microcontroller (MCU) with the mathematical throughput of a digital signal processor (DSP) in a single chip. In the semiconductor hierarchy, the DSC sits above general-purpose MCUs for math-intensive control loops and below application processors, making the dsPIC33F family a middle path between Microchip's PIC24 MCUs and dedicated DSPs, with seamless migration between the two.
Key features include a 16-bit modified Harvard architecture executing at 40 MIPS (operating frequency up to 40 MHz), 64 KB self-programming Flash, single-cycle multiply-accumulate DSP engine, and rich connectivity covering I2C, SPI, UART/USART, IrDA and LIN. Peripheral sets include AC'97 audio, DMA, I2S, input capture/output compare channels, and brown-out detect/reset, enabling compact single-chip control designs.
Technically, the dsPIC33F core integrates a DSP engine with dual 40-bit accumulators and hardware divide support, alongside a flexible clock system with on-chip PLL, low-jitter oscillators and fail-safe clock monitoring. The GP (General Purpose) variant emphasizes broad peripheral balance rather than motor-control-specific PWM modules of the MC variants.
Typical applications include digital power supplies and LED drivers, audio signal processing, sensor fusion and industrial automation nodes, and general embedded control where DSP-class math is required without a second processor.
For design, connect all VDD/VSS and AVDD/AVSS pins, and note that multiple PGECx/PGEDx pin pairs exist - use any pair, but keep ICSPCLK and ICSPDAT on the same selected pair for programming and debugging.
This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in same-family alternatives, pinout data, and practical design notes in one citable reference.
드롭인 대체품: DSPIC33FJ64GP306-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DSPIC33FJ64GP306-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature, Package, Mounting Type, Connectivity, Core Architecture.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
DSPIC33FJ64GP306A-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DSPIC33FJ128GP306-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$4.55 / 개
데이터시트 보기 →DSPIC33FJ32GP306-I/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DSPIC33FJ256GP306-I/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DSPIC33FJ256GP506AT-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$4.95 / 개
데이터시트 보기 →DSPIC33FJ64GP306-I/PT 최대 정격 & 전기적 특성
| Core | dsPIC33F (16-bit) |
| Max Speed | 40 MIPS |
| Operating Frequency | 40 MHz |
| Flash Program Memory | 64 KB |
| Core Size | 16-bit |
| Operating Voltage | 3.0 V to 3.6 V |
| 동작 온도 | -40C to +85C (TA) |
| Connectivity | I2C, SPI, UART/USART, IrDA, LIN |
| Peripherals | AC'97, Brown-out Detect/Reset, DMA, I2S |
| 패키지 | 64-TQFP (10x10 mm) |
| 실장 유형 | Surface Mount |
| Programming | ICSP (In-Circuit Serial Programming) |
| Debug Interfaces | Multiple PGECx/PGEDx pairs (use as a pair) |
| Migration Path | Seamless to PIC24 MCU and dsPIC30F DSC in similar packages |
| Family | dsPIC33F General Purpose (GP) |
| Supply Voltage Nominal | 3.3 V |
DSPIC33FJ64GP306-I/PT 핀 구성
| 핀 1 | MCLR — Master clear reset (active low), programming voltage input |
| 핀 2 | AN0/VREF+/CN2/RB0 — Analog input 0 / ADC positive reference / change notification |
| 핀 3 | AN1/VREF-/CN3/RB1 — Analog input 1 / ADC negative reference |
| 핀 4 | AN2/SS1/LVDIN/CN4/RB2 — Analog input 2 / SPI1 slave select / low-voltage detect input |
| 핀 5 | AN3/INDX/CN5/RB3 — Analog input 3 / quadrature index input |
| 핀 6 | AN4/QEA/IC7/CN6/RB4 — Analog input 4 / quadrature A / input capture 7 |
| 핀 7 | AN5/QEB/IC8/CN7/RB5 — Analog input 5 / quadrature B / input capture 8 |
| 핀 8 | AN6/OCFA/RB6 — Analog input 6 / output compare fault A |
| 핀 9 | AN7/RB7 — Analog input 7 / digital I/O |
| 핀 10 | VDD — Positive supply (3.0-3.6 V) |
| 핀 11 | VSS — Ground reference |
| 핀 12 | AN8/RB8 — Analog input 8 / digital I/O |
| 핀 13 | AN9/RB9 — Analog input 9 / digital I/O |
| 핀 14 | AN10/T2CK/RC0 — Analog input 10 / Timer 2 external clock |
| 핀 15 | AN11/T3CK/RC1 — Analog input 11 / Timer 3 external clock |
| 핀 16 | AN12/T4CK/RC2 — Analog input 12 / Timer 4 external clock |
| 핀 17 | AN13/T5CK/RC3 — Analog input 13 / Timer 5 external clock |
| 핀 18 | AN14/CN1/RC4 — Analog input 14 / change notification |
| 핀 19 | AN15/OCFB/CN0/RC5 — Analog input 15 / output compare fault B |
| 핀 20 | VSS — Ground reference |
| 핀 21 | OSC1/CLKI/RC12 — Crystal oscillator input / external clock input |
| 핀 22 | OSC2/CLKO/RC15 — Crystal oscillator output / clock output |
| 핀 23 | VDD — Positive supply (3.0-3.6 V) |
| 핀 24 | SOSCI/CN1/RC13 — Secondary oscillator input (32.768 kHz) / change notification |
| 핀 25 | SOSCO/T1CK/CN0/RC14 — Secondary oscillator output / Timer 1 external clock |
| 핀 26 | RF2/U1RX/SDI2 — UART1 receive / SPI2 data input |
| 핀 27 | RF3/U1TX/SDO2 — UART1 transmit / SPI2 data output |
| 핀 28 | RF7/SDI1 — SPI1 data input |
| 핀 29 | RF0 — General-purpose I/O (UART2/CN remappable per PPS) |
| 핀 30 | RF1 — General-purpose I/O (UART2/CN remappable per PPS) |
| 핀 31 | RD8 — Digital I/O PORTD |
| 핀 32 | RD9 — Digital I/O PORTD |
| 핀 33 | RD10 — Digital I/O PORTD |
| 핀 34 | RD11 — Digital I/O PORTD |
| 핀 35 | VSS — Ground reference |
| 핀 36 | VDD — Positive supply (3.0-3.6 V) |
| 핀 37 | RF6/SDO1 — SPI1 data output |
| 핀 38 | RF5/SCK1 — SPI1 serial clock |
| 핀 39 | RF4/SDA1 — I2C1 data (open drain) |
| 핀 40 | RE0 — Digital I/O PORTE |
| 핀 41 | RE1 — Digital I/O PORTE |
| 핀 42 | RE2 — Digital I/O PORTE |
| 핀 43 | RE3 — Digital I/O PORTE |
| 핀 44 | RE4 — Digital I/O PORTE |
| 핀 45 | RE5 — Digital I/O PORTE |
| 핀 46 | RE6 — Digital I/O PORTE |
| 핀 47 | RE7 — Digital I/O PORTE |
| 핀 48 | AVDD — Analog positive supply - must be connected for ADC |
| 핀 49 | AVSS — Analog ground - must be connected for ADC |
| 핀 50 | RG2 — Digital I/O PORTG |
| 핀 51 | RG3 — Digital I/O PORTG |
| 핀 52 | RD12 — Digital I/O PORTD / change notification |
| 핀 53 | RD13 — Digital I/O PORTD / change notification |
| 핀 54 | RG0 — Digital I/O PORTG |
| 핀 55 | RG1 — Digital I/O PORTG |
| 핀 56 | RD0 — Digital I/O PORTD |
| 핀 57 | RD1 — Digital I/O PORTD |
| 핀 58 | RD2 — Digital I/O PORTD |
| 핀 59 | RD3 — Digital I/O PORTD |
| 핀 60 | RD4 — Digital I/O PORTD |
| 핀 61 | VSS — Ground reference |
| 핀 62 | VDD — Positive supply (3.0-3.6 V) |
| 핀 63 | RD5 — Digital I/O PORTD |
| 핀 64 | RD6 — Digital I/O PORTD |
일반적인 애플리케이션
DSPIC33FJ64GP306-I/PT 적합 용도: 6 애플리케이션s: Digital Power Supplies, Audio Signal Processing, Industrial Automation and Control Nodes, Sensor Fusion and Data Acquisition, Motor-adjacent Embedded Control, Portable and Battery-Powered Instruments.
Digital Power Supplies
The DSPIC33FJ64GP306-I/PT fits digitally controlled power supplies because its 40 MIPS 16-bit core with single-cycle multiply-accumulate executes PID and compensation algorithms at switching frequencies that a standard MCU cannot sustain. ADC input channels (AN0-AN15) sample output voltage and current, while output-compare channels and DMA keep feedback loops deterministic. Running at 3.0-3.6 V with brown-out detect, the DSC supervises its own rail integrity in mission-critical converters. Placed as the supervisory controller between the feedback divider and gate-driver inputs, it adds programmable soft-start, fault logging and adaptive control that fixed-function PWM controllers lack. The trade-off is firmware development effort versus analog-controller simplicity.
추천
Audio Signal Processing
The DSPIC33FJ64GP306-I/PT is well suited to embedded audio because it integrates AC'97 and I2S interfaces alongside a DSP engine that performs single-cycle MAC operations, enabling FIR/IIR filtering, mixing and effects at 40 MIPS. For a Bluetooth-speaker or intercom product, the DSC connects directly to an audio codec via I2S, processes the stream in firmware, and manages system control on the same chip - eliminating a separate MCU. At 64 KB Flash, mid-complexity effect chains fit; use the 128 KB GP306 sibling for heavier processing. The trade-off versus a dedicated audio DSP is lower raw throughput, offset by lower system cost and single-chip integration.
추천
Industrial Automation and Control Nodes
In factory automation, the DSPIC33FJ64GP306-I/PT serves as an intelligent sensor/actuator node: its -40C to +85C rating survives panel environments, the 64-TQFP provides abundant I/O through PORTB/PORTC/PORTD/PORTE/PORTF/PORTG, and connectivity covers I2C, SPI, UART, IrDA and LIN for PLC backbones and field buses. The DMA engine offloads data movement so the 40 MIPS core focuses on control algorithms, while input-capture channels timestamp encoder or sensor pulses in hardware. Deployed between analog sensors (on AN0-AN15) and a RS-485/LIN transceiver, the DSC implements local decision logic with deterministic timing. The industrial temperature suffix -I makes it appropriate for unconditioned factory floors.
추천
Sensor Fusion and Data Acquisition
The DSPIC33FJ64GP306-I/PT handles multi-sensor data acquisition because its 16-channel ADC input set (AN0-AN15) with external VREF+ support samples several analog sources synchronously, and the DSP engine executes calibration, filtering and FFT tasks in real time at 40 MIPS. In a vibration-monitoring or predictive-maintenance node, accelerometer and microphone signals enter through analog channels, DMA streams samples to RAM without CPU intervention, and the accumulated results ship over UART or SPI to a host. The 64 KB Flash stores both firmware and calibration tables; the 128 KB variant fits more buffers or on-device FFT tables. Brown-out detect guarantees data integrity through supply dips.
추천
Motor-adjacent Embedded Control
While the MC-series dsPIC33F parts carry dedicated motor PWM modules, the general-purpose DSPIC33FJ64GP306-I/PT still drives motion and positioning subsystems - such as stepper drivers, DC-servo supervisory loops, and BLDC host controllers - using output-compare channels and quadrature interfaces (QEA/QEB and INDX on RB3-RB5) that decode encoder feedback in hardware. At 40 MIPS, the DSC closes current loops fast enough for small motor applications while managing communication with a higher-level controller over LIN, UART or SPI. Designers needing 3-phase high-resolution PWM should step to the MC family, but for supervisory motion logic the GP306 offers the same core in a flexible general-purpose I/O arrangement.
추천
Portable and Battery-Powered Instruments
The DSPIC33FJ64GP306-I/PT suits handheld instruments - measurement meters, portable loggers, test accessories - by combining 3.0-3.6 V single-rail operation, integrated brown-out supervision, and a fail-safe clock system with PLL from a crystal or internal oscillator. The 64-TQFP 10x10 mm footprint balances I/O density against board area, and ICSP programming via any PGECx/PGEDx pair simplifies field firmware updates with two-wire tools like MPLAB SNAP. Its 40 MIPS DSP engine performs on-device averaging, filtering and unit conversion so raw readings upload over UART/USB-bridge links. Versus a PIC24 MCU, the added DSP headroom lets the same firmware grow into spectrum or waveform analysis features later.
추천
추천 제품 요약
엔지니어링 참조 데이터: DSPIC33FJ64GP306-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DSPIC33FJ64GP306A-I/PT | DSPIC33FJ128GP306-I/PT | DSPIC33FJ32GP306-I/PT | DSPIC33FJ256GP306-I/PT | DSPIC33FJ256GP506AT-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Speed | dsPIC33F, 40 MIPS | dsPIC33F, 40 MIPS | dsPIC33F, 40 MIPS | dsPIC33F, 40 MIPS | dsPIC33F, 40 MIPS | dsPIC33F, 40 MIPS |
| Flash Memory | 64 KB | 64 KB | 128 KB | 32 KB | 256 KB | 256 KB |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C (I grade) |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
주요 차별점
- Cost-optimized 64 KB point in the GP306 pinout (vs DSPIC33FJ256GP306-I/PT)
- Base-revision errata risk vs A-step (vs DSPIC33FJ64GP306A-I/PT)
- Right-sized memory for mid-complexity firmware (vs DSPIC33FJ128GP306-I/PT)
설계 노트
Connect ALL VDD (pins 10, 23, 36, 62), VSS (pins 11, 20, 35, 61), AVDD (pin 48) and AVSS (pin 49) pins. Per Northern Software dsPIC33FJ64GP306 guidance and Microchip programming documentation, leaving even one power pin unconnected can cause ICSP programming to fail. Decouple each VDD pin pair with 0.1 uF ceramic capacitors placed within 2-3 mm of the pin, plus one bulk 10 uF capacitor per supply domain. Keep the analog ground island under AVSS/AN pins separate from the digital return until a single star point.
The device offers multiple PGECx/PGEDx programming pin pairs. You may use any pair, but ICSPCLK (PGECx) and ICSPDAT (PGEDx) must be on the SAME selected pair - mixing PGEC2 with PGED1 will fail silently during programming. Route the chosen pair to your programming header with short traces and avoid loading them with LEDs or pull-downs. Also configure MCLR with a 10k pull-up to VDD; MCLR doubles as the high-voltage programming entry pin, so do not clamp it with a diode to VDD.
Operate from a regulated 3.3 V rail within the 3.0-3.6 V datasheet window. Estimated: at 40 MIPS with moderate I/O loading, core current is typically in the tens of mA range - budget the rail using your firmware's measured current, not the headline 40 MIPS figure. The secondary oscillator (SOSCI/SOSCO, pins 24-25) can run a 32.768 kHz crystal for RTCC while the primary 40 MHz clock derives from OSC1/OSC2 (pins 21-22) with the internal PLL; ensure crystal load capacitors match the crystal datasheet, typically 10-15 pF.
For ADC accuracy, keep analog traces (AN0-AN15, pins 2-19) away from SPI/UART switching lines on PORTF/PORTG, and reference the ADC divider to the clean AVDD/AVSS domain (pins 48-49). Use VREF+ (pin 2) with a precision reference such as a bandgap-based IC if better than the supply-rail-referenced accuracy is needed. The 64-TQFP exposed-lead footprint needs standard 0.2 mm pitch land patterns per IPC-7351 practices; verify paste stencil aperture to prevent bridging on the fine-pitch corner pins.
규정 준수 정보
Lead-free standard for current Microchip production; -I temperature grade indicates industrial -40C to +85C. Automotive AEC-Q100 status not stated in provided data - use the AT-suffix variant for automotive needs. RoHS/REACH certificates should be requested from Microchip.
