EFM32G200F32G-E-QFN32 - 32MHz Cortex-M3 MCU | Silicon Labs
부품 번호: EFM32G200F32G-E-QFN32 ✓ 활성EFM32G200F32G-E-QFN32 개요
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, digital interfaces, timers, and analog or communication peripherals on one semiconductor device. The EFM32G200 family belongs to the ARM Cortex-M3 microcontroller, embedded processor, and semiconductor hierarchy. Silicon Labs positions the Gecko family for applications that need efficient processing, autonomous peripheral operation, and low standby consumption without sacrificing real-time control capability.
Three principal features distinguish the EFM32G200F32G-E-QFN32: a 32 MHz ARM Cortex-M3 core, 32 KB of program Flash, and 8 KB of RAM. The device also provides 24 digital I/O pins and two 16-bit timers. Low-power operation reaches 0.6 uA in Stop mode, while run-mode consumption is specified at 180 uA/MHz. These characteristics make the MCU suitable for portable sensing, industrial control, connected equipment, and embedded automation.
The Gecko architecture uses hardware features intended to reduce CPU workload, including a Wake-up Interrupt Controller and autonomous peripheral operation. Fast wake-up behavior helps systems react to external events without continuously running the processor. The MCU supports programming through its Cortex-M3 ecosystem and is identified by the manufacturer's product family and device ordering information.
Typical uses include battery-powered environmental sensors, building-control endpoints, compact industrial controllers, robotics modules, and IoT devices connected to external radios or sensors. The 32 KB Flash capacity is suitable for focused firmware rather than large graphical applications, while 8 KB of RAM supports modest protocol buffers and real-time control state.
PCB design should preserve the manufacturer's recommended power, decoupling, ground, and exposed-pad layout. Place the QFN exposed pad on a properly sized ground copper region, keep high-current return paths away from sensitive analog inputs, and follow the pin-description table in the manufacturer datasheet when assigning all 32 package pins.
This product page combines core specifications, package and memory comparisons, verified drop-in alternatives, and practical implementation guidance. It helps engineers distinguish ordering-code differences, plan firmware and peripheral requirements, and assess whether the EFM32G200F32G-E-QFN32 fits a low-power embedded design.
드롭인 대체품: EFM32G200F32G-E-QFN32 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EFM32G200F32G-E-QFN32 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Run Mode Current, Digital I/O Pins, Timers, RAM.
EFM32G200F32-QFN32
✅ 드롭인가격 문의
데이터시트 보기 →EFM32G200F32G-E-QFN32R
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32G200F16-QFN32
✅ 드롭인가격 문의
데이터시트 보기 →EFM32G200F32G-E-QFN32 최대 정격 & 전기적 특성
| Core Processor | ARM Cortex-M3, 32-bit single core |
| Maximum CPU Frequency | 32 MHz |
| Program Memory | 32 KB Flash |
| RAM | 8 KB |
| Digital I/O Pins | 24 pins |
| Timers | 2 x 16-bit |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Stop Mode Current | 0.6 uA |
| Run Mode Current | 180 uA/MHz |
| Wake-up Interrupt Controller | Integrated |
| Memory Protection Unit | Integrated |
| 패키지 | 32-QFN, 6 x 6 mm |
| Exposed Pad | Present |
| 실장 유형 | Surface mount |
EFM32G200F32G-E-QFN32 32-qfn, 6 x 6 mm 핀 구성 가이드
EFM32G200F32G-E-QFN32(32-qfn, 6 x 6 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EFM32G200F32G-E-QFN32.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EFM32G200F32G-E-QFN32 적합 용도: 6 애플리케이션s: Battery-Powered Environmental Sensor, Industrial Control Endpoint, IoT Sensor Node, Building Automation Sensor, Compact Robotics Controller, Portable Measurement Device.
Battery-Powered Environmental Sensor
The EFM32G200F32G-E-QFN32 is well suited to a battery-powered environmental sensor because its 32 MHz Cortex-M3 core can process measurements while the low-power architecture supports 0.6 uA Stop-mode operation. The 32 KB of Flash accommodates drivers, sampling control, filtering, and a compact communications protocol without external program memory. Two 16-bit timers can pace sensor sampling and sensor-control intervals, while 24 digital I/O pins allow connections to a digital sensor, status indicators, and a radio enable line. Keep the radio and sensor disabled during inactive periods to convert the low Stop-mode figure into meaningful battery life.
추천
Industrial Control Endpoint
Use the EFM32G200F32G-E-QFN32 as a compact industrial control endpoint for digital I/O, counting, monitoring, and local logic. Its two 16-bit timers are useful for pulse counting, periodic maintenance tasks, and timing external actuators, while the 24 available digital I/O pins reduce the need for external logic. The 32 MHz ARM Cortex-M3 core provides deterministic responsiveness, and 32 KB of Flash leaves room for communications, diagnostics, and control code. Its 1.98 V to 3.8 V operating range supports low-voltage industrial designs, subject to the final I/O voltage and environmental requirements.
추천
IoT Sensor Node
The EFM32G200F32G-E-QFN32 provides a practical foundation for an IoT sensor node requiring local processing and modest protocol support. Its Cortex-M3 core runs up to 32 MHz, while 32 KB of Flash accommodates networking code, drivers, and application logic and 8 KB of RAM supports compact receive and transmit buffers. The 24 digital I/O pins can connect sensors, interrupts, and radio-control signals. Fast wake-up behavior and Stop-mode current of 0.6 uA help reduce energy use during idle intervals. Select a radio carefully because radio current and duty cycle usually dominate total battery consumption.
추천
Building Automation Sensor
The EFM32G200F32G-E-QFN32 can manage a low-cost building-automation sensor that detects occupancy, temperature, or contact events. Two 16-bit timers support periodic sensing and debounce timing, while the 24 digital I/O pins accept multiple switches, alarm outputs, and bus signals. The 32 KB Flash capacity is useful for protocol stacks, threshold logic, calibration data, and diagnostic routines. Its low-power stop behavior allows the node to sleep between events, and fast wake-up reduces response latency. For wired building systems, verify that all connected interface levels remain compatible with the microcontroller's specified operating conditions.
추천
Compact Robotics Controller
The EFM32G200F32G-E-QFN32 is appropriate for a small robotics controller that handles sensors, simple actuators, and local coordination. The 32 MHz ARM Cortex-M3 core handles real-time control tasks, while the two 16-bit timers can generate precise pulse widths, sample control signals, or drive timing sequences. With 24 digital I/O pins, the controller can interface encoders, switches, motor-control commands, and status LEDs. The 32 KB Flash capacity supports compact motion logic and communication routines, but it is not intended for large robotics frameworks. Validate motor transients and grounding separately from the low-voltage digital controller.
추천
Portable Measurement Device
The EFM32G200F32G-E-QFN32 supports a portable measurement instrument where low standby power and compact size are important. Its 32 KB Flash can store firmware for acquisition control, calibration, display updates, and a serial protocol, while 8 KB of RAM handles sampled data and control state. The two 16-bit timers are useful for periodic acquisition and interface timing. Operating from 1.98 V to 3.8 V simplifies low-voltage design planning, although the selected sensor and display may require regulated rails. Use the exposed-pad land pattern correctly and validate analog measurement accuracy separately from the digital controller.
추천
추천 제품 요약
엔지니어링 참조 데이터: EFM32G200F32G-E-QFN32 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EFM32G200F32-QFN32 | EFM32G200F32G-E-QFN32R | EFM32G200F16-QFN32 |
|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 32-QFN (6x6 mm) | 32-QFN (6x6 mm) | 32-QFN (6x6 mm) | 32-QFN (6x6 mm) |
| Core Processor | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit |
| Maximum Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 16 KB |
| RAM | 8 KB | 8 KB | 8 KB | 8 KB |
| Digital I/O Pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Timers | 2 x 16-bit | 2 x 16-bit | 2 x 16-bit | 2 x 16-bit |
주요 차별점
- Twice the Flash memory of the reduced-memory family member (vs EFM32G200F16-QFN32)
- Identical core, memory, and package configuration (vs EFM32G200F32-QFN32)
- Direct reel-configured ordering option (vs EFM32G200F32G-E-QFN32R)
설계 노트
Implement the 32-QFN footprint according to the manufacturer package drawing, including the exposed ground pad, solderable perimeter pads, and thermal-via arrangement. Place input and bulk-decoupling capacitors close to their associated supply pins and connect the exposed pad to a continuous ground plane. Verify pad dimensions, paste volume, and reflow profile against the current EFM32G datasheet rather than copying a generic QFN footprint.
Plan the 1.98 V to 3.8 V supply rail so that voltage droop, startup sequencing, and peripheral load current remain inside the device limits. Place local high-frequency bypass capacitance near each supply connection and use additional bulk capacitance where the source is distant. For battery-powered designs, measure both active and sleep current because the 0.6 uA Stop specification excludes current drawn by external sensors, regulators, and radios.
Assign all 32 package pins from the datasheet pin-description table and keep exposed-pad vias away from sensitive signal paths where practical. Route high-current or switching signals away from oscillator, reset, and low-level sensor inputs. Provide a clean ground reference beneath the device and use short return paths for signal and bypass-capacitor connections. This reduces susceptibility to switching noise and improves repeatability in low-power sensing systems.
Do not treat the EFM32G200F16-QFN32 as a fully equivalent substitution when firmware exceeds 16 KB: its Flash capacity is 50% lower than the 32 KB available in the target. Likewise, a suffix change can affect reel configuration, revision identity, or ordering requirements even when the electrical specifications appear identical. Confirm the complete ordering code, lifecycle status, and firmware size before approving a replacement.
규정 준수 정보
The manufacturer product page and EFM32G family materials should be checked for current declarations. No specific compliance conclusion was added without an explicit product-level declaration.