FT4222HQ-D-R - USB 2.0 to Quad SPI/I2C Bridge | FTDI
부품 번호: FT4222HQ-D-R ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.5 | $4.50 |
| 10 | $4.05 | $40.50 |
| 100 | $3.6 | $360.00 |
| 500 | $3.2 | $1,600.00 |
| 1,000 | $2.85 | $2,850.00 |
FT4222HQ-D-R 개요
A USB bridge IC is a mixed-signal interface device that converts one serial bus protocol into another so a host CPU can talk to peripherals it cannot address natively. In the FT4222H the USB 2.0 PHY and protocol stack sit on one side, while the downstream side exposes configurable SPI (single/dual/quad mode) and an I2C master/slave controller. This places the part inside the broader hierarchy: USB bridge -> serial interface IC -> interface & connectivity -> mixed-signal semiconductor.
Key features include support for multi-voltage I/O (3.3 V, 2.5 V, or 1.8 V VCCIO), an integrated 5 V1 to 3.3 V LDO requiring no external regulator, 128 bytes of OTP memory for vendor information, and an external 12 MHz crystal that feeds the internal PLL. The VQFN-EP package provides a low-thermal-resistance pad that allows sustained USB bus-powered operation without external heatsinking. GPIOs are multiplexed with the SPI data lines, allowing flexible board design.
The FT4222H uses a Hi-Speed USB 2.0 PHY with on-chip termination and a serial-interface engine, offloading all protocol handling from the host MCU. Suspend/resume, remote wake-up, and bus-powered operation are handled in hardware, which is why the part is widely used in plug-and-play dongles, LCD/LED display controllers, and industrial sensor hubs.
Typical applications include USB-to-SPI display bridges for TFT/OLED panels, USB-to-I2C sensor hubs, industrial USB instrumentation, and evaluation modules for FPGA/CPLD programming. The combination of Quad-SPI throughput and I2C in a single chip is particularly useful when a single USB port must drive both a high-bandwidth display and a cluster of low-speed sensors.
When designing with this part, place the 12 MHz crystal within 5 mm of the XIN/XOUT pins and provide a solid ground pour under the exposed pad. Add 100 nF decoupling on each VCCIO rail and 4.7 uF on VBUS. The OTP memory is write-protected after the first programming cycle, so commit vendor data only once.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone FTDI datasheet, giving procurement and engineering teams a single reference for the FT4222HQ-D-R.
드롭인 대체품: FT4222HQ-D-R — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: FT4222HQ-D-R (동일 폼 팩터 및 풋프린트) — 차이점: Function, OTP Memory, Package, USB Speed.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
FT4222H
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
FT4222HQ-C-T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
FT4222HQ-D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
FT4222HQ-D-R 사양
| 기능 | USB 2.0 to Quad-SPI / I2C Bridge Controller |
| USB Speed | Hi-Speed (480 Mbps) / Full-Speed (12 Mbps) USB 2.0 |
| Downstream Interfaces | Quad-SPI (up to 4 SPI slaves), I2C master/slave |
| Maximum Throughput | 53.8 Mbps |
| I/O Voltage (VCCIO) | 1.8 V / 2.5 V / 3.3 V (multi-voltage) |
| Supply Voltage (VBUS) | 5 V (USB bus powered) |
| Internal Regulator | 5 V1 to 3.3 V LDO integrated |
| Clock Source | External 12 MHz crystal (internal PLL) |
| OTP Memory | 128 bytes one-time-programmable |
| GPIOs | Multiplexed with SPI data lines |
| 패키지 | VQFN-32 EP (5x5 mm) |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40C to +85C |
| RoHS 상태 | Compliant |
FT4222HQ-D-R 핀 구성
| 핀 1 | VCCIO — I/O supply voltage (1.8 V / 2.5 V / 3.3 V) |
| 핀 2 | GND — Ground |
| 핀 3 | XIN — 12 MHz crystal input |
| 핀 4 | XOUT — 12 MHz crystal output |
| 핀 5 | VBUS — USB 5 V supply input |
| 핀 6 | GND — Ground |
| 핀 7 | RESET — Active-low reset input |
| 핀 8 | TEST — Test pin (per datasheet, leave NC in production) |
| 핀 9 | DM — USB D- data line |
| 핀 10 | DP — USB D+ data line |
| 핀 11 | GND — Ground |
| 핀 12 | SCL — I2C clock (master/slave) |
| 핀 13 | SDA — I2C data (master/slave) |
| 핀 14 | MOSI — SPI Master Out / Slave In (data 0) |
| 핀 15 | MISO — SPI Master In / Slave Out (data 1) |
| 핀 16 | IO2 — SPI data 2 (Quad-SPI WP#) |
| 핀 17 | IO3 — SPI data 3 (Quad-SPI HOLD#) |
| 핀 18 | SPICS — SPI chip select (active low) |
| 핀 19 | SPICLK — SPI clock |
| 핀 20 | GPIO0 — General-purpose IO 0 / SPI data |
| 핀 21 | GPIO1 — General-purpose IO 1 / SPI data |
| 핀 22 | GPIO2 — General-purpose IO 2 / SPI data |
| 핀 23 | GPIO3 — General-purpose IO 3 / SPI data |
| 핀 24 | VCC — 3.3 V internal LDO output |
| 핀 25 | GND — Ground |
| 핀 26 | NC — Not connected (per datasheet) |
| 핀 27 | NC — Not connected (per datasheet) |
| 핀 28 | NC — Not connected (per datasheet) |
| 핀 29 | NC — Not connected (per datasheet) |
| 핀 30 | NC — Not connected (per datasheet) |
| 핀 31 | NC — Not connected (per datasheet) |
| 핀 32 | EP — Exposed thermal pad (connect to GND) |
일반적인 애플리케이션
FT4222HQ-D-R 적합 용도: 6 애플리케이션s: USB to TFT/OLED Display Bridge, USB to I2C Sensor Hub, FPGA/CPLD Configuration Flash Loader, Industrial USB Instrumentation, LED Matrix Driver Bridge, USB Evaluation Module for Prototyping.
USB to TFT/OLED Display Bridge
The FT4222HQ-D-R's Quad-SPI mode delivers up to 53.8 Mbps downstream, sufficient to refresh small TFT and OLED panels from a USB host at 30+ fps. Its integrated 5 V1 to 3.3 V LDO and configurable VCCIO (1.8 V / 2.5 V / 3.3 V) mean no external regulator is required to match common display logic levels. The FT4222HQ-D-R sits between the USB VBUS rail and the panel's SPI pins, with frame data pushed from the host driver through the FTDI D2XX/D3XX library. Trade-off: the FT4222HQ-D-R adds one USB enumeration step but eliminates the host MCU that would otherwise have to bit-bang SPI.
추천
USB to I2C Sensor Hub
The FT4222HQ-D-R's I2C master/slave controller lets a USB host read clusters of I2C sensors (temperature, humidity, accelerometers) up to 400 kHz. The configurable VCCIO rail matches 1.8 V and 3.3 V sensor logic levels without level shifters. Placed between VBUS and the sensor I2C bus, with 4.7 kohm pull-ups on SCL/SDA, the FT4222HQ-D-R acts as a bus master. Trade-off vs a CP2112: the FT4222HQ-D-R is more expensive but adds Quad-SPI for an attached flash logging IC.
추천
FPGA/CPLD Configuration Flash Loader
The FT4222HQ-D-R's Quad-SPI throughput (up to 53.8 Mbps) makes it a compact USB-to-SPI flash programmer for FPGA configuration memories (e.g., EPCQ16, EPCQ32). The 128-byte OTP memory can store vendor IDs and bitstream version tags, simplifying factory programming. Placed between USB and the FPGA configuration flash SPI pins, the FT4222HQ-D-R can re-program the flash in seconds vs minutes over UART. Trade-off: requires a host-side FT_Prog-style loader, but eliminates the need for a JTAG programmer on the manufacturing fixture.
추천
Industrial USB Instrumentation
The FT4222HQ-D-R's industrial temperature range (-40C to +85C) and Hi-Speed USB 2.0 make it a fit for industrial USB instruments that stream SPI ADC data to a host. The integrated 5 V1 to 3.3 V LDO and bus-powered operation simplify enclosure design. Placed at the USB-B connector with downstream SPI to a 24-bit ADC, the FT4222HQ-D-R delivers 53.8 Mbps throughput, sufficient for kilohertz-rate multi-channel acquisition. Trade-off: industrial users must use shielded cables and add ESD protection on USB DP/DM lines.
추천
LED Matrix Driver Bridge
The FT4222HQ-D-R can drive LED matrix drivers that use SPI (e.g., APA102, SK9822) at the maximum 53.8 Mbps downstream throughput, supporting thousands of pixels per USB update. Its multi-voltage VCCIO matches 5 V and 3.3 V LED driver levels. Placed between the USB host and the LED data line, the FT4222HQ-D-R replaces a dedicated MCU, reducing BOM cost. Trade-off: the FT4222HQ-D-R has only one Quad-SPI port, so multi-string panels need additional FT4222H ICs.
추천
USB Evaluation Module for Prototyping
The FTDI UMFT4222EV-D development module uses the FT4222HQ-D-R, giving designers a USB-to-SPI/I2C prototyping platform before committing to a custom PCB. The 12 MHz external crystal, decoupling, and exposed-pad solder footprint are pre-routed, accelerating firmware development. Placed on a breadboard with FTDI D2XX drivers loaded, the FT4222HQ-D-R validates USB enumeration and SPI timing. Trade-off: the eval module adds USB connector and crystal cost that a production design can integrate on-board.
추천
추천 제품 요약
엔지니어링 참조 데이터: FT4222HQ-D-R — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | FT4222H | FT4222HQ-C-T | FT4222HQ-D |
|---|---|---|---|---|
| Brand | FTDI | FTDI | FTDI | FTDI |
| Package | VQFN-32 EP (5x5 mm) | VQFN-32 EP (5x5 mm) - same | VQFN-32 EP (5x5 mm) - same | VQFN-32 EP (5x5 mm) - same |
| USB Speed | Hi-Speed USB 2.0 (480 Mbps) | Hi-Speed USB 2.0 (480 Mbps) | Hi-Speed USB 2.0 (480 Mbps) | Hi-Speed USB 2.0 (480 Mbps) |
| Downstream Interface | Quad-SPI + I2C | Quad-SPI + I2C | Quad-SPI + I2C | Quad-SPI + I2C |
| Max Throughput | 53.8 Mbps | 53.8 Mbps | 53.8 Mbps | 53.8 Mbps |
| Crystal Required | 12 MHz external | 12 MHz external | 12 MHz external | 12 MHz external |
| Packaging | Tape & Reel (-D-R) | Tray | Tape & Reel (-T) | Bulk |
| Operating Temperature | -40C to +85C | -40C to +85C | 0C to +70C (commercial) | -40C to +85C |
주요 차별점
- Quad-SPI + I2C in one USB bridge IC (vs FT2232H)
- Multi-voltage VCCIO (1.8 V / 2.5 V / 3.3 V) (vs FT232HL-REEL)
- Integrated 5 V1 to 3.3 V LDO with 128-byte OTP (vs FT4222HQ-C-T)
설계 노트
Place the 12 MHz crystal within 5 mm of the FT4222HQ-D-R XIN and XOUT pins, route traces symmetrically, and surround them with a ground pour. Add the crystal manufacturer's recommended load capacitors (commonly 12 pF to 33 pF) directly across XIN and XOUT to GND. The exposed thermal pad (pin 32/EP) MUST be soldered to a grounded copper pour for thermal dissipation and electrical reference.
The FT4222HQ-D-R integrates a 5 V1 to 3.3 V LDO, but a 4.7 uF low-ESR capacitor on VBUS is required for USB inrush and a 100 nF on VCCIO is required for downstream logic noise. If the downstream SPI bus runs above 30 MHz, add a 10 uF bulk on VCCIO. VBUS can be supplied directly from the USB connector; no external 5 V regulator is required for bus-powered designs.
The 128-byte OTP memory in the FT4222HQ-D-R is one-time-programmable: once written, it cannot be erased or rewritten. Verify vendor data before committing. Do not connect the TEST pin (pin 8) to any signal in production; leave it per datasheet guidance. Suspend current rises if the I2C bus is held low during USB suspend, so release SCL/SDA before the host suspends.
규정 준수 정보
RoHS compliant per DigiKey and Mouser listings. Not AEC-Q100 qualified (consumer/industrial USB bridge). Lead-free reflow compatible per FTDI datasheet. REACH compliance not explicitly stated; assume compliant per FTDI policy.
