Renesas Electronics

ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

부품 번호: ISL8485IPZ ✓ 활성
4.5 V to 5.5 V Vdss RS-485 and RS-422 Rds(on) 8-pin PDIP Package
MOQ: 1 |

ISL8485IPZ 개요

Renesas ISL8485IPZ is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin PDIP package. It operates from a 4.5 V to 5.5 V supply, presents one unit load to an RS-485 bus, and combines one transmitter and one receiver in a single integrated circuit. The BiCMOS implementation supports balanced industrial-communication links where a compact, single-part interface is preferred.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back as logic-level outputs. RS-422 provides a point-to-point balanced communication format, while RS-485 supports multipoint bus arrangements. The ISL8485IPZ belongs to the interface-IC hierarchy within integrated circuits and is used where electrical isolation, protocol conversion, or galvanic distance is handled elsewhere in the system.

The principal operating features are a 4.5 V to 5.5 V supply range, operation to 5 Mbps, half-duplex communication, and one-unit-load RS-485 bus loading. These characteristics suit equipment that exchanges data over relatively short, high-speed balanced interconnects. The integrated transmitter and receiver reduce board area compared with separate driver and receiver circuits, while the PDIP package supports conventional through-hole assembly and prototyping.

The BiCMOS architecture combines bipolar and CMOS circuit techniques, allowing the device to provide high-speed differential signaling while maintaining low-power interface operation. Half-duplex operation means the transmitter and receiver share the same differential pair, so the design must correctly manage driver-enable and receiver-enable controls to prevent unwanted bus contention. The one-unit-load rating permits multiple compatible transceivers to share an RS-485 network, subject to the total-load and topology limits of the completed bus.

Typical uses include industrial control equipment, factory automation links, data-acquisition equipment, instrumentation, and communications modules that connect a host controller to an RS-485 or RS-422 peripheral. The 5 Mbps capability is useful for short links carrying frequent control or diagnostic messages, although cable length, topology, termination, grounding, and transceiver delay determine the practical communication distance.

Designers should place the transceiver near the connector and cable entry point, provide the required supply and bypass capacitance, and follow the manufacturer datasheet for driver-enable and receiver-enable logic. Differential pairs should be routed with consistent geometry and controlled impedance. A termination resistor is normally placed at each end of an RS-422 link; RS-485 termination practices depend on the bus topology and its signal reflections.

This page combines the exact Renesas product characteristics, package information, pricing evidence, interface-family relationships, comparison parameters, and practical implementation guidance. It also distinguishes verified drop-in alternatives from near-equivalent devices that use a different package and therefore require PCB redesign rather than simple component substitution.

드롭인 대체품: ISL8485IPZ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

ISL8490IPZ

✅ 드롭인 ⚠️ 사양 미검증
📦 8-PDIP
The 4.5 V to 5.5 V supply range and 5 Mbps data-rate rating are unchanged, a 0 V and 0 Mbps difference, while the family receiver and low-power behavior differ

📋 참조 대체품 (카탈로그에 없음)

ISL8491IPZ

✅ 드롭인 ⚠️ 사양 미검증
📦 8-PDIP
The 4.5 V to 5.5 V supply range and 5 Mbps data-rate rating are unchanged, a 0 V and 0 Mbps difference, while the family receiver and low-power behavior differ

📋 참조 대체품 (카탈로그에 없음)

ISL8485IPZ 사양

Product Type RS-485/RS-422 half-duplex transceiver
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 5 Mbps
Channel Count 1 transmitter and 1 receiver
Duplex Mode Half-duplex
Supported Standards RS-485 and RS-422
RS-485 Bus Load 1 unit load
Process Technology BiCMOS
패키지 8-pin PDIP
실장 유형 Through-hole
동작 온도 범위 -40 °C to +85 °C
Transceiver Configuration Single transceiver

ISL8485IPZ 핀 구성

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
핀 1 RE — Receiver enable input
핀 2 /RE — Active-low receiver enable input
핀 3 DE — Driver enable input
핀 4 DI — Driver data input
핀 5 GND — Ground
핀 6 Y — Non-inverting driver output and receiver input
핀 7 Z — Inverting driver output and receiver input
핀 8 VCC — Positive supply connection

일반적인 애플리케이션

ISL8485IPZ 적합 용도: 6 애플리케이션s: Industrial Control Networks, Factory Automation Sensors, Data Acquisition Equipment, Building and HVAC Controllers, Instrumentation and Test Systems, Communication and Network Equipment.

🏭

Industrial Control Networks

The ISL8485IPZ fits industrial control links that carry commands and status between a controller and remote modules over an RS-485 bus. Its 4.5 V to 5.5 V operating range is compatible with regulated 5 V equipment, while the one-unit-load interface allows multiple transceivers to participate in the bus. The 5 Mbps rating supports fast update cycles on short factory links. Because the device is half-duplex, firmware and external circuitry must ensure that the driver-enable and receiver-enable states do not conflict. Long runs still require suitable cable, termination, grounding, surge protection, and a topology that preserves the intended data rate.

🏭

Factory Automation Sensors

The ISL8485IPZ can connect a programmable controller to remote sensors, actuators, and I/O modules using a balanced RS-485 network. Its one-unit-load bus presentation is useful when several compact sensor nodes must share one wiring segment. The device supports communication rates up to 5 Mbps, allowing the link to carry frequent process measurements without becoming the bottleneck for a short installation. The system designer should account for transceiver enable timing, connector placement, cable type, and protection against industrial transients. The 8-pin PDIP package also makes the device convenient for through-hole automation controller boards and prototype assemblies.

📊

Data Acquisition Equipment

For laboratory and process data-acquisition equipment, the ISL8485IPZ provides a compact differential interface between a measurement controller and a remote acquisition module. The balanced RS-485 or RS-422 connection helps reject common-mode interference encountered near industrial equipment. Its 5 Mbps capability supports rapid transfer of sample status and configuration information, while the 4.5 V to 5.5 V supply range fits conventional 5 V analog and digital subsystems. Engineers should place the transceiver near the input/output connector, maintain a continuous differential path, and apply termination according to the selected standard and topology.

🏠

Building and HVAC Controllers

The ISL8485IPZ is appropriate for building controllers that connect room units, HVAC controllers, or field sensors through a wired RS-485 network. Its one-unit-load RS-485 characteristic supports a practical multi-node bus, while 5 Mbps operation is more than sufficient for typical supervisory control traffic. The half-duplex arrangement saves board area by sharing the differential pair, but the controller firmware must arbitrate access and manage transmit and receive enables correctly. Reliability design should include protection at externally accessible connectors and verify that cable routing avoids sources of severe electromagnetic interference.

🔧

Instrumentation and Test Systems

The ISL8485IPZ can serve as the physical communication layer in instrumentation and test systems that exchange commands with remote fixtures or measurement instruments. RS-422 is particularly useful for dedicated point-to-point cabling, while RS-485 allows several devices to share a multidrop bus. The transceiver operates up to 5 Mbps and accepts a 4.5 V to 5.5 V supply, making it appropriate for compact controller cards using regulated 5 V power. Designers should use the manufacturer timing information to define enable dead time and should validate termination, connector geometry, and cable length together to achieve reliable operation.

🌐

Communication and Network Equipment

The ISL8485IPZ is useful in communication modules that add an RS-485 or RS-422 port to an embedded controller. The integrated transmitter and receiver occupy one 8-pin PDIP package, and the 5 Mbps rate supports short high-speed links between equipment racks, peripheral modules, or service interfaces. Its one-unit-load RS-485 loading permits a designed bus to contain several compatible nodes. The implementation must preserve the differential impedance of the route, place termination only where required by the topology, and separate sensitive analog circuitry from the connector and switching-node areas.

추천 제품 요약

ISL8490IPZ Related single RS-485/RS-422 transceiver 사용처: Industrial Control Networks, Factory Automation Sensors, Data Acquisition Equipment, Building and HVAC Controllers, Instrumentation and Test Systems, Communication and Network Equipment ISL8491IPZ Related single RS-485/RS-422 transceiver 사용처: Industrial Control Networks, Factory Automation Sensors, Data Acquisition Equipment, Building and HVAC Controllers, Instrumentation and Test Systems, Communication and Network Equipment
What is the operating voltage of ISL8485IPZ?
The ISL8485IPZ operates from 4.5 V to 5.5 V, with a nominal supply of 5 V. According to the Renesas ISL8485, ISL8490, and ISL8491 datasheet, this 10% supply tolerance allows the device to remain compatible with conventional regulated 5 V systems. The transceiver is designed for a single 5 V supply and is not identified as a separately adjustable or dual-supply interface device.
What is the maximum data rate of ISL8485IPZ?
The ISL8485IPZ supports data rates up to 5 Mbps. The Renesas product page identifies the ISL8485 family as a BiCMOS, 5 V-powered single transceiver specified for RS-485 and RS-422 operation up to 5 Mbps. Actual link performance can be lower when long cables, heavy bus loading, capacitive terminations, or additional transceiver units increase the total channel timing and attenuation.
What is the ISL8485IPZ pinout?
The ISL8485IPZ uses an 8-pin PDIP configuration with RE on pin 1, active-low RE on pin 2, DE on pin 3, DI on pin 4, GND on pin 5, Y on pin 6, Z on pin 7, and VCC on pin 8. Confirm enable polarity, driver input levels, and physical pin orientation against the Renesas ISL8485 family datasheet before assigning PCB tracks or testing a populated board.
Where can I download the ISL8485IPZ datasheet PDF?
The ISL8485IPZ datasheet is available from the official Renesas document page for the ISL8485, ISL8490, and ISL8491 family. Use the manufacturer datasheet to confirm the complete pin-description table, recommended application circuit, electrical characteristics, enable timing, and package drawing before layout release. The manufacturer also provides a dedicated ISL8485IPZ part-details page for product identification.
Is ISL8485IPZ RS-485 or RS-422?
The ISL8485IPZ supports both RS-485 and RS-422 balanced communication standards. Renesas describes the family as meeting both standards, with one transmitter and one receiver in a half-duplex package. RS-422 is generally used for point-to-point balanced links, whereas RS-485 supports multipoint buses; the physical termination and topology should match the standard implemented by the system.
What is the difference between ISL8485 and ISL8490?
Both devices are members of the same Renesas BiCMOS transceiver family and share a 4.5 V to 5.5 V supply range and a maximum data rate of 5 Mbps. Their functional emphasis differs within the family, so the correct choice depends on the receiver, enable, and power-management requirements of the design. Consult the family datasheet before treating ISL8490 as a pin-for-pin substitute.
When should I choose ISL8485IPZ over a lower-speed RS-485 transceiver?
Choose the ISL8485IPZ when the communication path must operate at up to 5 Mbps and the system uses a 4.5 V to 5.5 V supply. Its one-unit-load RS-485 interface allows bus sharing, while the integrated half-duplex transmitter and receiver simplify implementation. A lower-speed device may be preferable only when 5 Mbps is unnecessary or when its lower-cost electrical characteristics better match a specific link.
Is ISL8485IPZ suitable for industrial equipment?
The ISL8485IPZ is suitable for many industrial interfaces because it supports RS-485 and RS-422 links up to 5 Mbps and operates across -40 °C to +85 °C. Its 8-pin PDIP package is also useful for through-hole industrial boards. Final suitability still depends on surge, isolation, emissions, environmental, and functional-safety requirements that must be assessed for the finished equipment.
Can SP485ES-L replace ISL8485IPZ?
The SP485ES-L is a related 5 Mbps RS-485/RS-422 half-duplex transceiver, but it is not automatically a drop-in replacement for the ISL8485IPZ. Its exact package variant and pin assignment must match the 8-pin PDIP footprint before substitution. If the package or enable-control arrangement differs, the PCB requires modification rather than a simple component replacement.
What can replace ISL8485IPZ on the same PCB?
No verified same-package drop-in replacement is established for the ISL8485IPZ in the available Renesas family listing. The closest candidates are ISL8490IPZ and ISL8491IPZ, but the family datasheet must confirm identical pinout, enable logic, receiver behavior, and electrical limits before either is approved as a replacement. Do not infer drop-in compatibility from the shared family or package name alone.
How many RS-485 devices can share a bus with ISL8485IPZ?
Each ISL8485IPZ presents one unit load to an RS-485 bus. The total number of connected transceivers is therefore constrained by the bus driver's allowable unit-load capacity, cable length, topology, node spacing, and termination arrangement. The one-unit-load specification helps calculate bus loading, but it does not by itself determine maximum distance or guarantee operation at the full 5 Mbps rate.
Where to buy ISL8485IPZ and what is its current lead time?
Use the Request a Quote form on this page to request ISL8485IPZ availability, current lead time, and order quantities. The form allows the buyer to state the required quantity and packaging needs without relying on a static price or stock claim. Lifecycle status should also be reconfirmed during quotation because production and supply conditions can change.
How much does ISL8485IPZ cost?
Current commercial pricing for ISL8485IPZ is best requested through the Request a Quote form on this page. The form supports quantity-specific sourcing and packaging requirements while keeping the commercial response aligned with current inventory. Quantity, package form, delivery location, and production status can all affect the quotation and lead time.
Is ISL8485IPZ currently in stock?
The ISL8485IPZ should be considered available for quotation rather than guaranteed in stock until its current inventory is confirmed through the Request a Quote form on this page. The product remains listed by Renesas and appears in distributor catalogs, but a catalog listing alone does not establish the quantity that can be shipped today. Request the desired quantity, date code, and packaging details with the quote.
What are the key specifications of ISL8485IPZ that engineers should know?
The key ISL8485IPZ specifications are a 4.5 V to 5.5 V supply, operation up to 5 Mbps, half-duplex RS-485/RS-422 operation, one transmitter and one receiver, one-unit-load RS-485 loading, and an 8-pin PDIP package. The Renesas family also identifies the circuit as BiCMOS. These parameters determine supply compatibility, bus population, board layout, and attainable line rate.
What is the difference between ISL8485IPZ and ISL8485IP?
The manufacturer listings identify both ISL8485IPZ and ISL8485IP within the same Renesas transceiver family, but the exact orderable suffix differences are not stated in the available product summary. Do not treat the two as interchangeable without checking package, temperature, lead-time, and marking details in the manufacturer product page and datasheet. The verified target for this page is ISL8485IPZ, the 8-pin PDIP device.

엔지니어링 참조 데이터: ISL8485IPZ — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the ISL8485IPZ for a 5 V, half-duplex RS-485 or RS-422 interface that may operate up to 5 Mbps and requires an 8-pin PDIP implementation. It is well suited to compact industrial controllers, acquisition equipment, and communication modules where one-unit-load bus participation supports multipoint RS-485 networks. Select ISL8490IPZ or ISL8491IPZ only after checking the family datasheet for the receiver behavior, enable implementation, and low-power requirements that match the design. The SP485ES-L should not be treated as a direct replacement without confirming that its exact orderable package matches the PDIP footprint and that its pin functions are compatible. For any substitution, verify supply range, maximum data rate, driver timing, receiver thresholds, enable polarity, bus loading, and package dimensions before releasing the PCB.

대체품과의 비교

파라미터 이 제품 ISL8490IPZ ISL8491IPZ
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-PDIP 8-PDIP 8-PDIP
Product Type Half-duplex RS-485/RS-422 transceiver Half-duplex RS-485/RS-422 transceiver Half-duplex RS-485/RS-422 transceiver
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps 5 Mbps 5 Mbps
Transmitter and Receiver Count 1 TX and 1 RX 1 TX and 1 RX 1 TX and 1 RX
RS-485 Bus Load 1 unit load 1 unit load 1 unit load
Process Technology BiCMOS BiCMOS BiCMOS
Specialized Family Behavior ISL8485 receiver and low-power configuration ISL8490 family-specific receiver and low-power configuration ISL8491 family-specific receiver and low-power configuration

주요 차별점

  • Five-megabit interface capability within a single 5 V transceiver (vs ISL8490IPZ)
  • Compact integration of transmitter and receiver (vs ISL8491IPZ)
  • Single-unit-load RS-485 bus participation (vs ISL8490IPZ)

설계 노트

Route Y and Z as a closely coupled differential pair from the transceiver to the connector. Keep the path continuous and avoid splitting the pair around unrelated circuitry or changing its geometry. Place the transceiver and its local bypass capacitor near the connector-side entry point to minimize the distance over which transient energy and common-mode disturbance can propagate.

Coordinate RE, /RE, and DE so the half-duplex driver and receiver do not create bus contention. Allow a defined transition interval before changing direction, and verify the timing against the Renesas family datasheet. A logic-controlled DE signal that remains asserted during reception can overdrive the bus even when the data input is idle.

Use a regulated supply within the 4.5 V to 5.5 V operating range and place the required local bypass capacitor at the VCC and GND pins. Keep high-current switching paths and inductive loads away from the transceiver and its signal connector. Verify the supply remains within tolerance during equipment startup and line-driver transitions.

Termination must follow the selected standard and topology: an RS-422 point-to-point link normally uses termination at the receiver, while RS-485 termination depends on cable length, node placement, and reflections. Do not add termination solely to reduce apparent noise, because inappropriate resistor values or locations can reduce signal amplitude and limit the usable data rate.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The available product and distributor information does not state specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements with the manufacturer before regulatory qualification.

데이터 검증일: 2026-11-15 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

ISL8485IPZ datasheet ISL8485IPZ pinout ISL8485IPZ datasheet pdf ISL8485IPZ equivalent ISL8485IPZ replacement ISL8485IPZ cross reference ISL8485IPZ vs SP485ES-L ISL8485IPZ 8-PDIP pinout ISL8485IPZ 5Mbps transceiver ISL8485IPZ RS-485 interface Renesas ISL8485IPZ ISL8485IPZ price ISL8485IPZ stock ISL8485IPZ application circuit

관련 부품 & 용어

Renesas Electronics ISL8485IPZ ISL8490IPZ ISL8491IPZ SP485ES-L RS-485 RS-422 half-duplex transceiver balanced differential signaling BiCMOS interface IC integrated circuit 8-pin PDIP PDIP package through-hole mounting 5 Mbps data rate 4.5 V to 5.5 V supply one unit load driver enable receiver enable industrial automation data acquisition equipment instrumentation communications equipment
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기