LAN8710AI-EZK-TR - 10/100 Ethernet PHY | Microchip Technology
부품 번호: LAN8710AI-EZK-TR ✓ 활성LAN8710AI-EZK-TR 개요
An Ethernet PHY is the physical-layer component that translates data between a host digital interface and copper cabling. The LAN8710A family supports 10 Mbps and 100 Mbps links, while MII and RMII connectivity allows it to pair with digital Ethernet controllers or application processors. Within the network hierarchy, the part operates below the Ethernet MAC and above the transformer-coupled 10/100BASE-T cable interface.
The device provides auto-negotiation for automatic speed and duplex selection and HP Auto-MDIX support, allowing direct-connect and crossover cables without a manual crossover switch. Its variable I/O voltage supports adaptation to the digital interface voltage, while the integrated regulator and ESD-protection components reduce external component count. The manufacturer identifies the LAN8710A family as a low-power, small-footprint solution for consumer, industrial, and enterprise applications.
The LAN8710AI-EZK-TR is part of the LAN8710A/LAN8710Ai family and supports both IEEE 802.3u MII and reduced-pin-count RMII interfaces. These host-side interfaces provide design flexibility for embedded processors, industrial controllers, set-top equipment, printers, network appliances, and other 10/100 Ethernet products. The 5 mm by 5 mm QFN footprint helps limit board area in space-constrained equipment.
Typical deployments include industrial automation controllers, network management appliances, embedded Ethernet equipment, printers, consumer-electronics accessories, and communications equipment. For a new design, confirm that the selected processor exposes a compatible MII or RMII interface and verify the required clock, supply, and magnetics requirements against the manufacturer datasheet before schematic release.
Layout quality is especially important around a high-speed mixed-signal device. Place the PHY close to the Ethernet connector and network magnetics, keep copper paths short, provide clean return paths, and follow the manufacturer reference layout. Differential-pair geometry, via symmetry, plane continuity, and isolation from noisy switching circuitry directly influence signal integrity and EMC performance.
This product summary combines the exact orderable MPN, package information, interface capabilities, family-level features, lifecycle information, and application guidance. It also identifies where application-specific electrical limits must be confirmed in the manufacturer datasheet before schematic and layout signoff.
드롭인 대체품: LAN8710AI-EZK-TR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LAN8710AI-EZK-TR (동일 폼 팩터 및 풋프린트) — 차이점: Package.
LAN8710A-EZK-TR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LAN8710AI-EZK
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LAN8710AI-EZK-TR 사양
| Product Type | 10/100 Ethernet PHY transceiver |
| Supported Data Rates | 10 Mbps and 100 Mbps |
| Ethernet Standards | IEEE 802.3-2005 |
| Host Interface | MII and RMII |
| Transceiver Channels | 1 channel |
| Cable Standard | 10BASE-T and 100BASE-TX |
| Auto-Negotiation | Supported |
| Auto-MDIX | HP Auto-MDIX supported |
| Integrated Voltage Regulator | Integrated |
| Integrated ESD Protection | Integrated |
| Variable I/O Voltage | Supported |
| 패키지 | 32-QFN, 5 mm x 5 mm |
| 실장 유형 | Surface mount |
| Temperature Grade | Industrial temperature |
| Packaging | Tape and reel |
| RoHS 상태 | Compliant |
| AEC-Q100 Qualification | Not applicable |
LAN8710AI-EZK-TR 32-qfn, 5 mm x 5 mm 핀 구성 가이드
LAN8710AI-EZK-TR(32-qfn, 5 mm x 5 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: LAN8710AI-EZK-TR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LAN8710AI-EZK-TR 적합 용도: 6 애플리케이션s: Industrial Automation Controller, Network Management Appliance, Embedded Linux Control System, Connected Printer, Consumer Electronics Accessory, Communications Equipment.
Industrial Automation Controller
The LAN8710AI-EZK-TR is suitable for a compact industrial controller that needs a 10/100 Ethernet management or communications link. Its MII and RMII host interfaces allow connection to an embedded processor or Ethernet controller, while 10 Mbps and 100 Mbps support accommodates common factory-network traffic. Auto-negotiation selects speed and duplex automatically, and HP Auto-MDIX removes the need for a manual crossover connection. The 5 mm by 5 mm 32-QFN footprint preserves board area for densely populated control equipment. For deployment, verify the exact temperature range, isolation needs, magnetics, and reference-layout requirements before production release.
추천
Network Management Appliance
The LAN8710AI-EZK-TR provides a compact copper-network interface for management appliances, access units, and small gateways operating at 10 or 100 Mbps. The MII interface supports conventional parallel MAC signaling, while RMII offers a lower-pin-count option for compatible processors. Integrated voltage regulation and ESD protection can reduce external component requirements, and the integrated PHY keeps the host board compact. The device's auto-negotiation and HP Auto-MDIX features simplify interoperability with installed network equipment. Designers should confirm regulator output requirements, magnetics selection, isolation strategy, and thermal performance against the enclosure and operating environment.
추천
Embedded Linux Control System
The LAN8710AI-EZK-TR can connect an embedded Linux processor to a 10/100BASE-T network through MII or RMII. The RMII option is especially useful where board routing and connector space are constrained, while MII provides compatibility with controllers that expose the wider parallel interface. The PHY supports auto-negotiation and HP Auto-MDIX, allowing the operating system to establish a link with standard switches and direct peer connections. Its small 32-QFN package supports compact control hardware. Firmware and board design must coordinate RMII timing, reference-clock routing, strap configuration, and driver support before the interface can operate reliably.
추천
Connected Printer
The LAN8710AI-EZK-TR supports a wired print server or connected printer requiring a standard 10/100 Ethernet port. At 100 Mbps, it provides sufficient throughput for network printing, management traffic, and firmware distribution, while auto-negotiation allows operation on both 10 Mbps and 100 Mbps links. HP Auto-MDIX simplifies installation with either straight-through or crossover cabling. The small 5 mm by 5 mm package is useful inside compact printers and print-server boards. The system integrator should still account for Ethernet magnetics, isolation, connector layout, thermal conditions, and the host processor's supported MII or RMII interface.
추천
Consumer Electronics Accessory
The LAN8710AI-EZK-TR is appropriate for consumer-electronics accessories that add a compact wired-network connection, such as media appliances, smart-home gateways, or set-top accessories. Its low-footprint 32-QFN package supports board-area reduction, while the integrated regulator and ESD protection can simplify implementation. MII and RMII interfaces provide host flexibility, and auto-negotiation plus HP Auto-MDIX improve setup compatibility with consumer routers and switches. Because these products can be exposed to ESD from cable disconnection and variable consumer environments, the complete design should follow the manufacturer's reference layout and magnetics recommendations rather than relying only on the integrated PHY protection.
추천
Communications Equipment
The LAN8710AI-EZK-TR can provide a 10/100 management-network path in communications equipment, access terminals, and network-interface modules. Supporting both MII and RMII lets the product follow different host-controller architectures, while auto-negotiation simplifies links to legacy 10 Mbps and modern 100 Mbps infrastructure. HP Auto-MDIX permits direct and crossover cable connections, reducing installation constraints in field-service applications. The compact QFN package allows Ethernet connectivity to be added where connector and magnetics placement dominate board area. Final qualification should check the exact industrial temperature limits, isolation, EMC margin, firmware interface support, and environmental requirements for the deployed enclosure.
추천
추천 제품 요약
엔지니어링 참조 데이터: LAN8710AI-EZK-TR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LAN8710A-EZK-TR | LAN8710AI-EZK |
|---|---|---|---|
| Package | 32-QFN (5x5 mm) | 32-QFN (5x5 mm) | 32-QFN (5x5 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Product Type | 10/100 Ethernet PHY transceiver | 10/100 Ethernet PHY transceiver | 10/100 Ethernet PHY transceiver |
| Supported Data Rates | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps |
| Host Interface | MII and RMII | MII and RMII | MII and RMII |
| Ethernet Compliance | IEEE 802.3-2005 | IEEE 802.3-2005 | IEEE 802.3-2005 |
| Auto-Negotiation | Supported | Supported | Supported |
| Auto-MDIX | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported |
| Temperature-Grade Designation | Industrial-temperature I designation | Non-I designation; exact limits differ | Industrial-temperature I designation |
| Ordering Packaging | TR tape-and-reel suffix | TR tape-and-reel suffix | No TR suffix; reel configuration differs |
주요 차별점
- Maintains the industrial-temperature ordering designation (vs LAN8710A-EZK-TR)
- Preserves the exact industrial-temperature device identity (vs LAN8710AI-EZK)
- Combines MII and RMII with integrated protection functions (vs LAN8710A-EZK-TR)
설계 노트
Place the LAN8710AI-EZK-TR, Ethernet magnetics, and RJ45 connector in the same compact signal path. Route the Ethernet analog and digital differential nets as short, symmetrical pairs with matched via transitions and continuous reference planes. Keep the RMII or MII host traces away from the magnetics and connector area, and follow the manufacturer reference layout to minimize skew, insertion loss, and EMC radiation.
Design the supply network around the exact core and variable I/O voltage requirements in the manufacturer datasheet. Keep the PHY and its decoupling network close together, provide a low-impedance return path, and place bulk and high-frequency capacitors at the locations shown by the reference design. Verify startup sequencing, regulator headroom, and load behavior at the intended Ethernet line rate rather than assuming the integrated regulator eliminates all board-level constraints.
Validate the MII or RMII interface timing, reference clock, and control signals under the selected operating mode. For RMII, use a clean, low-jitter clock source and match trace lengths where the interface implementation requires it. For MII, review setup and hold timing across the complete operating-temperature range. Leave test access for signal measurement and use the manufacturer's evaluation-board schematic as a reference for the intended PHY configuration.
Do not treat functional-equivalent cross-reference listings as proof that a substitute is pin-compatible. Verify package dimensions, exposed-pad requirements, pin names, strap configuration, register behavior, clock requirements, temperature grade, and ESD architecture. The LAN8710AI-EZK and LAN8710A-EZK-TR differ in ordering temperature-grade information, and the absence of the TR suffix changes reel configuration even though the electrical family is closely related.
규정 준수 정보
RoHS compliance is reported in the manufacturer-family product information. AEC-Q100 is not applicable to this industrial Ethernet transceiver. REACH, lead-free, halogen-free, and conflict-minerals status are unknown.