LM258H/NOPB - Dual 32V 700kHz Op Amp | Texas Instruments
부품 번호: LM258H/NOPB ✓ 활성LM258H/NOPB 개요
An operational amplifier is an active analog component that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. Within the semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories. Internally compensated designs simplify closed-loop implementation because they do not require an external compensation capacitor, although stability still depends on the gain, load, and feedback network selected by the designer.
The principal features of the LM258H/NOPB are its dual-amplifier configuration, 700 kHz gain-bandwidth product, 32 V supply rating, and -25°C to 85°C operating-temperature range. It is designed for operation from a single positive supply or split supplies. Two independent amplifiers can implement separate gain stages, differential buffering, comparators, or active filters within one package, reducing board area when a conventional metal-can package is appropriate.
The LM258 family uses a bipolar voltage-feedback architecture with internal frequency compensation. At low closed-loop gains, internal compensation provides stable operation without external compensation components. The maximum output current, input bias current, input offset voltage, slew rate, common-mode input range, and output swing limits must be checked against the exact operating conditions in the manufacturer datasheet before a high-impedance or precision design is released.
Typical uses include low-frequency active filters, transducers, sensor interfaces, sample-and-hold stages, and general-purpose control loops. Industrial instrumentation can benefit from the relatively high supply-voltage tolerance, while audio and communications equipment can use the two amplifiers for independent signal paths. The metal-can TO-99 construction also makes the device suitable for established through-hole industrial designs that predate surface-mount packages.
When laying out an LM258H/NOPB circuit, keep feedback-loop traces short, place input and output compensation or decoupling components close to their associated pins, and avoid long unprotected routes beside high-current switching nodes. Check the available output-current margin against the load, because a dual amplifier does not increase the current rating of either individual output stage. The leaded package requires adequate hole clearance and mechanical support where vibration or thermal cycling is significant.
This product page combines the manufacturer identification, ordering information, family-level specifications, package details, application guidance, and engineering-oriented selection criteria. It also distinguishes drop-in family options by temperature range and supply behavior, helping designers reuse an existing TO-99 layout without overlooking qualification, grounding, or input-common-mode restrictions.
드롭인 대체품: LM258H/NOPB — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM258H/NOPB (동일 폼 팩터 및 풋프린트) — 차이점: Gain-Bandwidth Product, Operating Temperature Range.
LM158H/NOPB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM358H/NOPB
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM2904H/NOPB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM258AH/NOPB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM358AH/NOPB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM258H/NOPB 최대 정격 & 전기적 특성
| Amplifier Count | 2 amplifiers |
| Product Type | Dual general-purpose operational amplifier |
| Maximum Supply Voltage | 32 V |
| Manufacturer Family Supply Rating | 30 V |
| Gain-Bandwidth Product | 700 kHz |
| 동작 온도 범위 | -25°C to +85°C |
| 패키지 | TO-99-8 metal can |
| Total Pin Count | 8 pins |
| Architecture | Voltage-feedback bipolar operational amplifier |
| Frequency Compensation | Internally frequency compensated |
| Supply Configuration | Single or split supply |
| Amplifier Independence | 2 independent amplifiers |
| 실장 유형 | Through-hole |
| RoHS 상태 | Compliant |
LM258H/NOPB to-99-8 metal can 핀 구성 가이드
LM258H/NOPB(to-99-8 metal can 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LM258H/NOPB.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LM258H/NOPB 적합 용도: 6 애플리케이션s: Industrial Sensor Signal Conditioning, Audio Preamplifier and Buffering, Power Supply Feedback Control, Active Filter and Waveform Conditioning, Communications Receive Chain, Test and Measurement Front End.
Industrial Sensor Signal Conditioning
The LM258H/NOPB suits low-frequency sensor-conditioning stages that must operate from -25°C to +85°C. Its two internally frequency-compensated amplifiers can process separate sensor channels without requiring external compensation capacitors, while the 700 kHz gain-bandwidth product provides more bandwidth than most slow sensor signals require. Place the device near the sensor interface, use short feedback paths, and keep high-impedance input traces away from switching nodes. Because the two amplifiers share a package and supply, each output must remain within the device's load-current capability. Verify input bias current, offset voltage, common-mode range, and output swing for the particular sensor before finalizing the gain network.
추천
Audio Preamplifier and Buffering
LM258H/NOPB can provide general-purpose voltage gain and impedance buffering for low-frequency audio-control or line-level paths. Its 700 kHz gain-bandwidth product supports audio-band amplification, and the internal compensation removes the need for an external stability capacitor in standard closed-loop configurations. One amplifier may amplify a source while the other buffers an output or forms an active filter. The TO-99 metal-can package is mechanically robust for legacy and industrial audio equipment. Keep the feedback loop compact, observe the output-swing limits at the chosen supply voltage, and ensure the load does not exceed the individual output-stage current rating. Input and output grounding should use a quiet return path to avoid adding ground-dependent noise.
추천
Power Supply Feedback Control
The LM258H/NOPB is appropriate for slow feedback loops in linear power-supply and voltage-control circuits where a 700 kHz gain-bandwidth product is adequate. One amplifier may compare a scaled feedback voltage with a reference, while the other can provide error amplification, gain, or an additional buffer. Internal frequency compensation simplifies conventional closed-loop layouts, but loop stability still depends on the power-stage pole, compensation network, and load. Keep the high-impedance comparison node short and shielded from power-stage switching activity. Confirm common-mode input range across the complete supply startup and load range. The -25°C to +85°C specification makes this ordering code appropriate for industrial environments that remain within that envelope.
추천
Active Filter and Waveform Conditioning
LM258H/NOPB can implement first-order active filters, integrators, and waveform-conditioning networks at low frequencies. The 700 kHz gain-bandwidth product gives substantial loop bandwidth compared with many sensor, control, and audio-band signals, while internal compensation supports common closed-loop configurations without an added compensation capacitor. Two independent amplifiers allow separate filter sections or a cascaded two-stage response in one through-hole package. Select resistor and capacitor values so the desired closed-loop gain remains compatible with the amplifier's stability behavior, and check each capacitor's dielectric characteristics for the signal frequency. Place feedback components directly beside their associated pins and maintain symmetrical routing to minimize added delay and unintended feedback.
추천
Communications Receive Chain
LM258H/NOPB can serve as a low-frequency gain or buffer stage within established communications equipment that uses through-hole analog boards. Its two-channel architecture can handle separate receive paths, and its 700 kHz gain-bandwidth product is suitable for many baseband and control signals rather than high-definition radio-frequency amplification. The 32 V ordering rating accommodates established industrial supply rails, but actual rail current and common-mode headroom must be verified. Use a single low-impedance ground reference, keep input leads short, and isolate the amplifier from motor contacts, relay transients, and switching supplies. For RF or wideband applications, select a higher-bandwidth amplifier; LM258H/NOPB is primarily a general-purpose, low-frequency signal-conditioning device.
추천
Test and Measurement Front End
LM258H/NOPB can form a buffer, gain stage, or active filter ahead of instrumentation and measurement converters. Two independent amplifiers make it possible to condition a differential pair, preserve source impedance, or combine filter and buffer functions in one 8-pin TO-99 package. Its 700 kHz gain-bandwidth product is suitable for many low- and mid-band measurement signals, while the -25°C to +85°C range covers typical controlled industrial or laboratory environments. Keep high-impedance nodes away from panel wiring and relay contacts, and terminate unused amplifier inputs according to the datasheet guidance. Confirm offset, bias-current, common-mode, and output-swing requirements before claiming measurement accuracy.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM258H/NOPB — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM158H/NOPB | LM358H/NOPB | LM2904H/NOPB | LM258AH/NOPB | LM358AH/NOPB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | TO-99-8 | TO-99-8 | TO-99-8 | TO-99-8 | TO-99-8 | TO-99-8 |
| Amplifier Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature Range | -25°C to +85°C | -55°C to +125°C | 0°C to +70°C | -40°C to +125°C | -55°C to +125°C | -55°C to +125°C |
| Frequency Compensation | Internal | Internal | Internal | Internal | Internal | Internal |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
주요 차별점
- Broader standard-temperature coverage than the LM358H option (vs LM358H/NOPB)
- Narrower temperature rating than the industrial LM2904H option (vs LM2904H/NOPB)
- Lower-temperature operation than the military-grade LM158H option (vs LM158H/NOPB)
설계 노트
Treat the TO-99 metal-can orientation as a mechanical and electrical constraint, not merely a footprint choice. Confirm the pin-numbering diagram and package dimensions in the Texas Instruments LM258 datasheet before releasing the PCB. Both amplifier sections must have valid input states, unused inputs should be connected according to the datasheet guidance, and the common-mode input range must be checked at startup as well as during normal operation.
Place input, feedback, and compensation components directly beside their associated TO-99 pins to minimize parasitic capacitance and feedback-loop area. Route the two amplifier channels separately where they carry uncorrelated signals, and keep high-impedance input nets away from relay contacts, inductors, and switching-node copper. The long through-hole leads provide useful layout flexibility, but excess lead length can increase coupling and make the feedback behavior harder to predict.
Check each amplifier's output current independently because the two sections do not increase the current capability of the other section. The LM258H/NOPB supports single or split supply operation, but the usable input and output range changes with the rail voltage. Verify common-mode headroom and output swing for the minimum supply used during startup. A bypass capacitor near the supply pins should be selected from the datasheet's recommended network and kept on the same ground reference as the analog signal path.
Use a 700 kHz gain-bandwidth product as the principal bandwidth reference and keep the intended closed-loop gain within the stable operating range of the internally compensated amplifier. Avoid relying on excessive closed-loop gain to overcome input-offset or noise limitations. For active filters and integrators, verify capacitor dielectric behavior at the signal frequency and keep the feedback loop compact so parasitic delay does not alter phase margin.
규정 준수 정보
RoHS compliance is identified in the manufacturer part comparison information. No definitive REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification status was identified for this exact ordering code.