LM2902KNSE4 - Quad 26V 1.2MHz Op-Amp | Texas Instruments
부품 번호: LM2902KNSE4 ✓ 활성LM2902KNSE4 개요
A quad operational amplifier is an analog IC that integrates four op-amp cores on a single die, sharing supply and ground pins while keeping each amplifier's inputs and outputs independent. Op-amps belong to the linear-amplifier family of semiconductors, positioned under the broader categories of amplifiers, analog signal conditioning ICs, and power management signal chains. Quad integration reduces board area, bill-of-material count, and per-channel cost compared with four single op-amps.
Key features of the LM2902KNSE4 include a wide single-supply range (3 V to 26 V), common-mode input range that extends to ground (ground-sensing capability), and the automotive temperature grade associated with the LM2902 family. The improved LM2902K variant adds a 2 kV ESD rating per TI product information. Outputs can source and sink current without external protection in most configurations, and the internal compensation removes the need for external frequency-setting components.
Architecturally, the LM2902 follows the classic bipolar silicon process used in industry-standard quad op-amps. The internal 1.2 MHz compensation makes each channel unity-gain stable, while the low, supply-independent quiescent drain supports battery-powered and low-power industrial designs. The biasing scheme keeps channel-to-channel coupling low, so one amplifier driving a load does not materially disturb the others.
Typical applications include automotive signal conditioning (sensor buffers and comparators on 12 V/24 V rails), industrial control loops and 4-20 mA transmitters, active filters and summing stages in audio and instrumentation, and low-side current-sense amplification in power supplies. The automotive grade and wide supply range make it well suited to vehicle-level electronics where cold-crank and load-dump conditions compress supply headroom.
When designing with this device, keep the common-mode input range within the datasheet limits - inputs beyond the negative rail can cause phase inversion, and outputs cannot swing fully to the positive rail under load. Decouple the shared supply pin with 0.1 uF placed close to pin 4.
This page adds value beyond the manufacturer datasheet: distributor sourcing links, drop-in alternative comparisons with parametric matching, per-application design guidance, and layout notes compiled from TI application literature.
드롭인 대체품: LM2902KNSE4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM2902KNSE4 (동일 폼 팩터 및 풋프린트) — 차이점: Slew Rate, Package, Packaging, Gain Bandwidth Product, Number of Amplifier Circuits.
LM2902DR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM2902DG4
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM2902DE4
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM324ADR2G
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM324ADRG4
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM2902KNSE4 최대 정격 & 전기적 특성
| Amplifier Type | General Purpose |
| Number of Circuits | 4 |
| Gain Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/us |
| Supply Voltage Range (Single) | 3 V to 26 V |
| Supply Voltage Range (Dual) | +/-13 V |
| Quiescent Current (Per Amplifier, Typ) | 0.8 mA |
| ESD Rating | 2 kV (improved LM2902K) |
| Temperature Grade | Automotive |
| 패키지 / 케이스 | 14-SOIC (0.209 in, 5.30 mm width) |
| 실장 유형 | Surface Mount |
| Terminal Form | Gull Wing |
| Packaging | Tube |
| Number of Terminals | 14 |
LM2902KNSE4 핀 구성
| 핀 1 | OUT1 — Output of amplifier 1 |
| 핀 2 | IN1- — Inverting input of amplifier 1 |
| 핀 3 | IN1+ — Non-inverting input of amplifier 1 |
| 핀 4 | VCC — Positive supply |
| 핀 5 | IN2+ — Non-inverting input of amplifier 2 |
| 핀 6 | IN2- — Inverting input of amplifier 2 |
| 핀 7 | OUT2 — Output of amplifier 2 |
| 핀 8 | OUT3 — Output of amplifier 3 |
| 핀 9 | IN3- — Inverting input of amplifier 3 |
| 핀 10 | IN3+ — Non-inverting input of amplifier 3 |
| 핀 11 | VEE/GND — Negative supply or ground |
| 핀 12 | IN4+ — Non-inverting input of amplifier 4 |
| 핀 13 | IN4- — Inverting input of amplifier 4 |
| 핀 14 | OUT4 — Output of amplifier 4 |
일반적인 애플리케이션
LM2902KNSE4 적합 용도: 6 애플리케이션s: Automotive Sensor Signal Conditioning, Industrial Current Sensing and Transmitters, Active Filters and Signal Conditioning, Power Supply Monitoring and Control, Battery-Powered Portable Instrumentation, Motor Drive and Position Feedback Electronics.
Automotive Sensor Signal Conditioning
The LM2902KNSE4 fits automotive sensor buffering because it combines an automotive temperature grade, a 26 V single-supply rating, and a common-mode input range that extends to ground, allowing direct interface with ground-referenced resistive sensors such as throttle position, coolant level, and pressure bridges. Each of the four channels can buffer a separate sensor, cutting component count on body-control and powertrain boards. Placed close to the sensor connector with 0.1 uF decoupling at pin 4, the 1.2 MHz channels provide stable unity-gain buffering without oscillation. Because the output cannot swing to the positive rail, design the ADC scale so full-scale signals stay below VCC minus roughly 1.5 V under load.
추천
Industrial Current Sensing and Transmitters
In 4-20 mA loop transmitters and low-side current-sense circuits, the LM2902KNSE4 provides the gain stages and output driver on 24 V industrial rails. Its supply range up to 26 V covers standard industrial power without an additional regulator stage, and the ground-sensing input range simplifies shunt measurement near 0 V. A typical topology uses one channel to amplify the shunt voltage by 50x to 100x, a second as an integrator driving the pass transistor, and the remaining two for range scaling. The 0.8 mA-per-channel quiescent drain keeps loop overhead low, and the 0.5 V/us slew rate is ample for the slow control loops of process transmitters.
추천
Active Filters and Signal Conditioning
The four matched channels of the LM2902KNSE4 make it economical for multi-stage active filters - Sallen-Key low-pass, multiple-feedback band-pass, and anti-aliasing stages - on a single SOIC-14 footprint. Internal compensation makes each channel unity-gain stable, so Sallen-Key sections with unity-gain buffers work directly, and the 1.2 MHz gain-bandwidth product supports corner frequencies up to roughly 10 kHz at Q values above 1 with modest gain error. In audio and instrumentation front ends, the ground-inclusive common-mode range allows single-supply AC-coupled topologies biased at mid-supply from a divider buffered by a spare channel. Keep closed-loop gains moderate to preserve phase margin near the bandwidth limit.
추천
Power Supply Monitoring and Control
The LM2902KNSE4 serves as the error amplifier and supervision channel in off-line and DC-DC power supplies. One channel acts as the voltage-loop error amplifier comparing a divided output against a reference, while a second implements overvoltage or overcurrent latching via a comparator-style connection; the 26 V rating tolerates bias from 12 V and 24 V auxiliaries directly. Because the amplifier output is designed to interface with optocoupler LEDs in isolated supplies, the classic TL431-plus-op-amp secondary loop is straightforward. Add a 0.1 uF decoupling capacitor at pin 4 and keep the compensation network traces short; the ground-reaching input range permits shunt-based current-limit sensing near the primary return.
추천
Battery-Powered Portable Instrumentation
With a typical quiescent drain of 0.8 mA per channel that is largely independent of supply voltage, the LM2902KNSE4 suits battery instruments operating from 3 V to 24 V packs, including 3-cell lithium-ion stacks and 12 V lead-acid batteries. Four channels on one die reduce board area and standby bias compared with discrete singles, supporting portable data loggers, handheld meters, and wireless sensor nodes. The internal compensation removes startup stability concerns when supplies ramp slowly from a soft-switch. Design the signal range so outputs stay above a few hundred millivolts of either rail, since the class-B output stage does not swing rail-to-rail under load, and buffer high-impedance dividers with a spare channel.
추천
Motor Drive and Position Feedback Electronics
In DC and stepper motor drive electronics, the LM2902KNSE4 implements current-limit amplifiers, tachometer signal conditioning, and PWM ramp generation on a single quad die. Its 26 V single-supply rating connects directly to 12 V and 24 V drive rails, and one channel can difference-sense the motor shunt with inputs near ground. The 0.5 V/us slew rate and 1.2 MHz bandwidth are sufficient for generating sawtooth PWM carriers up to the tens-of-kHz range typical of small drives. Keep the current-sense filter bandwidth well below the amplifier's limit to avoid amplifying switching spikes, and use the remaining channels for reference buffering and fault-level comparison to reduce bill-of-material count.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2902KNSE4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2902DR | LM2902DG4 | LM2902DE4 | LM324ADR | LM324ADRG4 |
|---|---|---|---|---|---|---|
| Package | 14-SOIC (5.30 mm width) | 14-SOIC (5.30 mm width) - same | 14-SOIC (5.30 mm width) - same | 14-SOIC (5.30 mm width) - same | 14-SOIC (5.30 mm width) - same | 14-SOIC (5.30 mm width) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Circuits | 4 | 4 | 4 | 4 | 4 | 4 |
| Gain Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Slew Rate | 0.5 V/us | 0.5 V/us | 0.5 V/us | 0.5 V/us | 0.5 V/us | 0.5 V/us |
| Maximum Supply Voltage | 26 V | 26 V | 26 V | 26 V | 32 V | 32 V |
| Improved ESD Rating | 2 kV (LM2902K) | Standard | Standard | Standard | Standard | Standard |
| Temperature Grade | Automotive | Automotive | Automotive | Automotive | Commercial | Commercial |
| Quiescent Current (Typ, Per Amplifier) | 0.8 mA | 0.8 mA | 0.8 mA | 0.8 mA | 0.8 mA | 0.8 mA |
| Packaging | Tube | Tape & Reel | Tube | Tape & Reel | Tape & Reel | Tape & Reel |
주요 차별점
- Improved 2 kV ESD robustness (vs LM2902DR)
- Automotive temperature grade (vs LM324ADR)
- Tube packaging for prototype builds (vs LM2902DR)
설계 노트
Decouple the shared VCC pin (pin 4) with a 0.1 uF ceramic capacitor placed within a few millimeters of the pin, plus bulk capacitance as required by the load. Because all four channels share one supply node, a fast output stage can couple transients into the other three amplifiers through the supply; tight decoupling and a solid ground plane suppress this channel-to-channel crosstalk. Route sensitive inverting-node traces (pins 2, 6, 9, 13) short and guard them from adjacent output traces to avoid unintended feedback and oscillation.
Two classic LM2902 limitations must be respected. First, the output stage does not swing to the positive rail - under load, expect the high output to sit roughly 1.5 V below VCC, so design ADC scales and comparator thresholds with this headroom. Second, inputs can sense down to ground but performance degrades when the common-mode voltage approaches the positive rail; keep inputs comfortably below VCC minus about 1.5 V. Driving large capacitive loads directly can cause ringing - add a small series isolation resistor (about 50 ohm) at the output, per the stability guidance in the TI application literature for the LM2902 family.
The 1.2 MHz gain-bandwidth product is generous for DC and low-frequency conditioning but finite: at a closed-loop gain of 100, the -3 dB bandwidth falls to roughly 12 kHz with visible phase lag. For filter sections, verify the corner frequency against available bandwidth so Q does not peak unexpectedly. Because the channels share a die, thermal gradients from a hot channel can shift the offset of neighboring channels slightly; in precision applications, spread high-dissipation functions across channels or reserve one channel as a nulling buffer.
Estimated: with four channels each drawing a typical 0.8 mA quiescent current at 24 V, standby drain is roughly 3.2 mA x 24 V = about 77 mW, well within the SOIC-14 thermal capability with no heatsinking. Add load-current dissipation per channel when outputs drive significant loads continuously; at 10 mA output drive with 10 V headroom, each such channel adds an estimated 100 mW. Total dissipation below a few hundred milliwatts keeps junction temperature far below limits in standard 4-layer or 2-layer boards.
규정 준수 정보
The E4 suffix on TI parts historically denotes RoHS/green compliance packaging, but explicit RoHS and REACH status for this exact MPN was not stated in the sourced listings; confirm on the TI product page before ordering.