LM2903ATH-13 - Dual Differential Comparator, TSSOP-8 | Diodes Inc
부품 번호: LM2903ATH-13 ✓ 활성LM2903ATH-13 개요
A voltage comparator is an analog circuit element that compares two input voltages and drives its output to indicate which is higher. Within the signal-chain hierarchy, the comparator sits alongside operational amplifiers as a member of the analog IC family: where an op-amp amplifies the difference, a comparator saturates its output to a logic-compatible level, making it a bridge between the analog and digital domains. The LM2903 family - originally introduced by multiple manufacturers and now offered by Diodes Incorporated as the LM2903 series - is the industry-reference dual comparator used worldwide.
Key features of the LM2903ATH-13 include two independent comparators with high open-loop gain, a wide supply range spanning single or dual supplies up to ±18V/36V, low input offset characteristics, and open-collector outputs that support wired-OR configurations and flexible logic-level translation. The TSSOP-8 package provides a compact surface-mount footprint suitable for dense boards, and the device is positioned by Diodes Incorporated for industrial, automotive, and consumer electronics applications.
Technically, each comparator in the LM2903ATH-13 is a differential amplifier stage with a PNP input pair that allows input common-mode voltages extending down to the negative rail, including slightly below ground in single-supply operation. The open-collector output stage requires an external pull-up resistor, which lets designers adapt the output swing to 3.3V, 5V, or higher logic rails independently of the comparator supply. Hysteresis, when needed, is added with a small amount of positive feedback around the comparator.
Typical applications include voltage threshold detection and supervision in power supplies, level shifting between analog front ends and microcontroller inputs, oscillator and timing circuits, current-sense limit detection, and signal conditioning in industrial and automotive electronic control units.
A key design consideration is that the open-collector output mandates a pull-up resistor to the desired logic rail, and for slowly moving input signals a few millivolts of hysteresis should be added to prevent output chatter near the switching threshold.
This page adds value beyond the manufacturer datasheet by consolidating drop-in alternative comparisons, pinout information, application guidance, and sourcing details in one place for design and procurement engineers.
드롭인 대체품: LM2903ATH-13 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM2903ATH-13 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Logic Compatibility, Comparator Type, Output Type, Number of Comparators.
LM2903TH-13
✅ 드롭인가격 문의
데이터시트 보기 →LM293AM
✅ 드롭인가격 문의
데이터시트 보기 →LM293AN
✅ 드롭인가격 문의
데이터시트 보기 →LM393AM
✅ 드롭인가격 문의
데이터시트 보기 →LM2903ATH-13 최대 정격 & 전기적 특성
| 기능 | Dual differential voltage comparator |
| Number of Comparators | 2 |
| Supply Voltage Range (Dual) | ±1 V to ±18 V |
| Supply Voltage Range (Single) | 2 V to 36 V |
| 출력 유형 | Open collector |
| Input Type | Differential (PNP input pair) |
| 패키지 | 8-TSSOP |
| 실장 유형 | Surface Mount |
| Product Series | LM2903 (Diodes Incorporated) |
| Common-Mode Range | Includes negative rail (ground-sense capable) |
| Application Segment | Industrial, automotive, consumer electronics |
LM2903ATH-13 핀 구성
| 핀 1 | OUT A — Comparator A output (open collector, requires pull-up) |
| 핀 2 | IN A- — Comparator A inverting input |
| 핀 3 | IN A+ — Comparator A non-inverting input |
| 핀 4 | GND / V- — Ground or negative supply |
| 핀 5 | IN B+ — Comparator B non-inverting input |
| 핀 6 | IN B- — Comparator B inverting input |
| 핀 7 | OUT B — Comparator B output (open collector, requires pull-up) |
| 핀 8 | VCC / V+ — Positive supply, up to 36 V single or ±18 V dual |
일반적인 애플리케이션
LM2903ATH-13 적합 용도: 6 애플리케이션s: Power Supply Voltage Supervision, Automotive ECU Threshold Detection, Industrial Signal Conditioning, Current-Sense Limit Detection, Relaxation Oscillators and Timing, Battery-Powered Consumer Devices.
Power Supply Voltage Supervision
The LM2903ATH-13 fits power-supply supervision because its two independent comparators allow overvoltage and undervoltage detection from a single 8-pin package, and its supply range up to ±18V/36V tolerates high-voltage industrial rails. One comparator monitors a resistor divider against an internal or external reference for OV trip, while the second handles UV trip, driving a fault flag or shutdown pin through the open-collector output. Because the inputs sense down to the negative rail, dividers referenced to ground work directly without level shifting. Use a few millivolts of hysteresis via positive feedback to avoid chatter near the threshold, and pull up the output to the logic rail of the supervising controller for clean digital signaling.
추천
Automotive ECU Threshold Detection
The LM2903ATH-13 is positioned by Diodes Incorporated for automotive electronics, and its wide temperature-grade packaging plus 36V tolerance suit the load-dump-prone 12V vehicle environment. In ECUs it serves as a battery voltage watchdog, sensor-limit detector, and switch-state decoder: divider-scaled signals from battery sense lines, knock sensors, or hall switches are compared against fixed thresholds, and the open-collector outputs interface directly to the microcontroller port with a pull-up to 5V. The dual comparators in one TSSOP-8 footprint reduce component count on densely packed PCBAs. Designers should add hysteresis on slow analog inputs and respect the differential input voltage limits during crank transients.
추천
Industrial Signal Conditioning
In industrial signal chains, the LM2903ATH-13 converts slowly varying analog levels from sensors, potentiometers, and 4-20mA loop-derived voltages into clean digital limit flags. Its input common-mode range includes the negative rail, which allows direct ground-referenced comparison of divider-scaled process signals, and the ±18V dual-supply capability matches classic industrial analog front ends running on ±15V rails. Each comparator can implement one limit of a window detector, with outputs wire-ORed through a single pull-up for combined pass/fail signaling to a PLC input. The high open-loop gain provides sharp switching even for millivolt-level differences near the setpoint, provided noise filtering and modest hysteresis are included.
추천
Current-Sense Limit Detection
The LM2903ATH-13 implements fast overcurrent detection by comparing the differential voltage across a low-value shunt resistor against a reference threshold. The ground-sensing input pair allows low-side current sensing where the shunt sits between load and ground: one input reads the shunt node while the other reads a resistor-divided threshold derived from the supply or a precision reference. When the sensed current exceeds the limit, the open-collector output pulls low and latches attention in the controller or triggers a soft-start disable. Keep shunt lead inductance low, add an RC filter on the sense input to reject switching noise, and set hysteresis wide enough to avoid repeated trips at the current boundary.
추천
Relaxation Oscillators and Timing
With positive feedback and an RC network, each half of the LM2903ATH-13 forms a relaxation oscillator for watchdog timing, clock generation, or LED blinkers. The comparator switches when the capacitor voltage crosses the hysteresis band set by the feedback resistor divider around the non-inverting input, and the open-collector output discharges the timing capacitor through a resistor, setting frequency approximately as f = 1 / (RC) scaled by the divider ratio. Operation from a single 5V or wide 36V supply lets the same oscillator circuit serve both logic-board and high-voltage industrial contexts. Use stable NP0-class timing components and account for input bias current when choosing large resistor values for low-frequency operation.
추천
Battery-Powered Consumer Devices
In battery-operated consumer electronics, the LM2903ATH-13 provides low-cost battery-low indication and power-good detection. Its single-supply operation from 2V upward covers two-cell and USB-powered systems, and the ground-inclusive input range allows direct monitoring of divider-scaled pack voltage without a negative rail. One comparator drives an LED or processor alarm when the pack drops below the UV threshold; the second can monitor charger presence or temperature-derived thresholds. The open-collector output draws no static high-side current, conserving battery energy, and the compact TSSOP-8 footprint fits space-constrained handheld boards. Choose large divider resistance values and verify comparator input bias effects to keep the monitoring path quiescent draw negligible.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2903ATH-13 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2903TH-13 | LM293AM | LM293AN | LM393AM |
|---|---|---|---|---|---|
| Package | 8-TSSOP | 8-TSSOP - same | LM2903/LM293 8-pin pinout - verify package suffix | LM2903/LM293 8-pin pinout - verify package suffix | LM2903/LM393 8-pin pinout - verify package suffix |
| Brand | Diodes Incorporated | Diodes Incorporated | onsemi | onsemi | onsemi |
| Number of Comparators | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage (Max) | 36 V (±18 V dual) | 36 V (±18 V dual) | 36 V (±18 V dual) | 36 V (±18 V dual) | 36 V (±18 V dual) |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector |
| Target Segment | Industrial, automotive, consumer | Industrial, consumer | Industrial | Industrial | Consumer |
| Input Common-Mode Range | Includes negative rail | Includes negative rail | Includes negative rail | Includes negative rail | Includes negative rail |
주요 차별점
- Automotive-grade packaging (vs LM393AM)
- Same-brand footprint-compatible variant available (vs LM2903TH-13)
- Wide 36V supply tolerance (vs modern low-voltage comparators)
설계 노트
Each open-collector output of the LM2903ATH-13 requires a pull-up resistor sized for the sink current and required rise time - typical values of 3.3k to 10k to a 3.3V or 5V rail work for most logic interfaces. Place the pull-up close to the output pin and route the output trace away from the inverting input to prevent feedback-induced oscillation. Compare both inputs against the same ground reference plane, and keep the input traces short when source impedances exceed 10k, since input bias currents convert into offset on high-impedance nodes.
When the input signal traverses the threshold slowly, the LM2903ATH-13 output can oscillate as noise re-trips the comparator. Add hysteresis with a positive-feedback resistor from output to the non-inverting input; with an open-collector output, calculate both trip points using the actual pull-up voltage rather than VCC. Additionally, a small capacitor (10-100 pF) directly across the comparator inputs can filter fast glitches, but avoid excessive capacitance on high-impedance nodes since it slows response and can aggravate chatter rather than cure it.
Three pitfalls recur with LM2903-class comparators. First, respect the differential input voltage limit during transients - clamp inputs when comparing nodes that can exceed the rated differential range, such as during load dump in 12V automotive systems. Second, do not drive the inputs below V- beyond the common-mode spec; ground-sensing does not mean unlimited negative swing. Third, unused comparators must have defined inputs - tie the unused non-inverting input to a rail through a divider and ground the other so the open-collector output sits in a defined state and does not dither the supply.
규정 준수 정보
Compliance statuses are not stated in the retrieved product listings; request RoHS/REACH declarations through the Request a Quote form. The A suffix in the part number indicates the automotive-grade package per Diodes Incorporated naming convention.