LMG708B0RXR - 20A GaN Synchronous Buck 80VIN | Texas Instruments
부품 번호: LMG708B0RXR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1 | $1.00 |
| 10 | $1 | $10.00 |
| 100 | $1 | $100.00 |
| 500 | $1 | $500.00 |
| 1,000 | $1 | $1,000.00 |
LMG708B0RXR 개요
A GaN synchronous buck converter is a step-down DC-DC switching regulator that uses gallium-nitride FETs as the power switches. In the power-management hierarchy it sits within the DC-DC converter subsystem, converting higher-voltage distribution rails to lower point-of-load voltages for processors, logic, and mixed-signal loads. GaN transistors exhibit very low gate charge and output capacitance, enabling faster switching transitions and dramatically lower switching losses than silicon MOSFETs, which is especially valuable at high step-down ratios such as 48V-to-12V and 48V-to-5V.
Key features include the fully integrated controller-plus-GaN power-stage architecture, 20A continuous output current, and near-zero deadtime that minimizes body-diode conduction loss. The integrated approach eliminates external high-side/low-side FET selection and simplifies gate-drive PCB layout. Low RDS(on) reduces conduction loss at full load, yielding high efficiency across a broad load range, while high-frequency capability permits smaller inductors and output capacitors for maximum power density.
The 80V maximum input rating provides substantial headroom for 48V industrial distribution buses, telecom -48V infrastructures, and automotive load-dump transients. Output configuration flexibility - resistor-divider adjustable or fixed 5V/12V - allows one footprint to serve multiple rail requirements.
Typical applications include 48V industrial bus converters, telecom line cards, server power shelves, 48V automotive subsystems, and high-current LED lighting drivers. The wide input and output ranges make it an effective front-end point-of-load solution for 12V, 5V, or lower core rails at currents up to 20A.
Design tip: place low-ESR ceramic input capacitors close to VIN and PGND to handle steep high-frequency current steps, and use thermal vias under the exposed pad to hold junction temperature below 125C. Follow the TI datasheet layout guidelines for optimum switching performance and EMI behavior.
드롭인 대체품: LMG708B0RXR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LMG708B0RXR (동일 폼 팩터 및 풋프린트) — 차이점: Output Voltage Range, Topology.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
LMG708B0QRXRQ1
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →LMG708B0QRXRQ1
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
가격 문의
데이터시트 보기 →LMG5126QRXRQ1
⚡ 동일 패키지✓ 재고 있음
가격 문의
데이터시트 보기 →LMG708B0RXR 최대 정격 & 전기적 특성
| 토폴로지 | Synchronous Step-Down (Buck) |
| 입력 전압 범위 | 5 V to 80 V |
| 최대 출력 전류 | 20 A |
| 출력 전압 범위 | 1 V to 55 V (adjustable) |
| Fixed Output Options | 5 V or 12 V |
| Power Switches | Integrated low RDS(on) GaN FETs |
| Switching Characteristic | Near-zero deadtime switching |
| Maximum Junction Temperature | 125 C |
| 패키지 | VQFN-28 (RXR) |
| 실장 유형 | Surface Mount |
| Product Family | High power density GaN synchronous buck |
| Key Benefit | Ultra-high current density and excellent power conversion efficiency |
| Typical Applications | 48V bus converters, telecom, server power |
LMG708B0RXR vqfn-28 (rxr) 핀 구성 가이드
LMG708B0RXR(vqfn-28 (rxr) 패키지)의 핀 구성입니다. 이 전력 소자는 게이트, 드레인, 소스 단자를 갖추고 있습니다. 비편향 패키지의 경우 정확한 핀 1 방향과 풋프린트 세부 정보는 제조사 데이터시트를 참조하십시오. 일반적인 응용 분야로는 전원 공급 장치 설계, 모터 구동, 부하 스위칭이 있습니다.
다음에 대한 상세 핀아웃 데이터 없음: LMG708B0RXR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LMG708B0RXR 적합 용도: 6 애플리케이션s: 48V Industrial Bus Converters, Server Power Shelves, Telecom Line Cards, 48V Automotive Subsystems, High-Current LED Lighting Drivers, Point-of-Load Core Rails.
48V Industrial Bus Converters
The LMG708B0RXR converts 48V industrial distribution rails directly to 12V or 5V at up to 20A, with the 80V input rating supplying margin for bus transients. Integrated GaN FETs with near-zero deadtime reduce switching losses at high step-down ratios, improving efficiency and shrinking inductor size. Place ceramic input capacitors at VIN and use the exposed-pad thermal vias to keep the junction under 125C in sealed industrial enclosures.
추천
Server Power Shelves
In datacenter power shelves, the LMG708B0 delivers dense 48V-to-12V intermediate-bus conversion at 20A per phase. GaN near-zero deadtime switching raises efficiency versus silicon, cutting thermal load per rack. TI's LMG708B0-EVM2PH (12V, 40A, 400kHz two-phase EVM) validates multiphase scaling; two LMG708B0 phases interleave to double output current while halving input/output ripple.
추천
Telecom Line Cards
Telecom infrastructure distributes power at -48V nominal; the LMG708B0's 80V input tolerance covers surges on rectified telecom feeds. It steps down to 12V or 5V point-of-load rails at up to 20A per device. High efficiency at full load reduces heatsink needs on densely packed line cards, while the adjustable 1V to 55V output range accommodates custom ASIC and DSP core voltages.
추천
48V Automotive Subsystems
For 48V automotive zonal loads (mild-hybrid belts, e-compressor auxiliaries), the Q1-qualified LMG708B0QRXRQ1 in the identical RXR package handles battery transients within its 80V input rating. GaN efficiency at 20A minimizes waste heat under the hood. Use the fixed 12V output option for legacy 12V accessory rails, and follow the datasheet layout guide for EMI compliance in vehicle environments.
추천
High-Current LED Lighting Drivers
High-bay and stage lighting fixtures use 48V LED strings; the LMG708B0 supplies controlled high-current rails up to 20A with the efficiency advantage of integrated GaN FETs. Its adjustable output (1V to 55V) supports series LED stack voltages, and 80V input headroom absorbs AC-line-derived transients. Compact VQFN-28 integration allows the driver electronics to fit within slim luminaire housings.
추천
Point-of-Load Core Rails
For processors, FPGAs, and DSPs fed from a 48V or 24V backplane, the LMG708B0 provides a single-chip front-end conversion to 5V or lower core rails at 20A. The fixed-output options simplify BOM for common rails, while adjustable mode supports custom core voltages down to 1V. Low output ripple from GaN fast switching eases downstream filtering for noise-sensitive analog and RF loads.
추천
추천 제품 요약
엔지니어링 참조 데이터: LMG708B0RXR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LMG708B0QRXRQ1 | LMG5126QRXRQ1 |
|---|---|---|---|
| Package | VQFN-28 (RXR) | VQFN-28 (RXR) - same | VQFN-28 (RXR) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Power Switches | Integrated GaN FETs | Integrated GaN FETs | GaN family device |
| Qualification | Industrial/consumer grade | Automotive Q1 | Automotive Q1 |
주요 차별점
- Integrated GaN power stage with near-zero deadtime (vs LM70860RRXR (6A silicon-class 80V buck))
- Automotive Q1 same-package option (vs LMG708B0QRXRQ1)
- Wide adjustable output to 55V (vs LMG5126QRXRQ1)
설계 노트
Place low-ESR ceramic input capacitors immediately adjacent to the VIN and PGND pins to source the steep high-frequency current steps created by GaN fast switching. Minimize the high-side switching loop area; the integrated GaN stage has much faster edge rates than silicon, so short, wide power traces and a solid ground plane are essential for low EMI and clean switching waveforms.
The maximum junction temperature is 125C. At 48V-to-12V, 20A operation, use an array of thermal vias under the VQFN-28 exposed pad connecting to internal and bottom-layer copper pours. Estimate dissipation from I2R of the GaN RDS(on) plus switching losses, and verify with the TI LMG708B0-EVM2PH two-phase EVM thermal measurements for high-current designs.
Do not exceed the 80V absolute input rating - 48V buses with load-dump or surge events require input transient suppression. For the adjustable output variant, use 1% or better feedback divider resistors. When paralleling phases for currents above 20A (as in the EVM2PH), follow the TI two-phase current-sharing guidance to prevent one phase from carrying disproportionate load.
규정 준수 정보
Compliance details not captured in verified data; commercial LMG708B0RXR is not the Q1 automotive variant. Consult ti.com/product/LMG708B0 for certifications. AEC-Q100-qualified operation requires the LMG708B0QRXRQ1.
