M25P32-VMW3GB - 32Mbit SPI NOR Flash 75MHz | Micron
부품 번호: M25P32-VMW3GB ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1.85 | $1.85 |
| 10 | $1.66 | $16.60 |
| 100 | $1.48 | $148.00 |
| 500 | $1.33 | $665.00 |
| 1,000 | $1.18 | $1,180.00 |
M25P32-VMW3GB 개요
Serial NOR flash is a nonvolatile memory category in which data is accessed byte-wise over a serial peripheral interface (SPI) rather than a wide parallel bus. Within the memory hierarchy - memory IC -> flash memory -> NOR flash -> serial SPI NOR flash - these devices trade raw bandwidth for dramatically reduced pin count, tiny board footprint, and low cost, which is why they are the de facto standard for storing boot code, firmware images, and configuration data in embedded systems.
Key features of the M25P32-VMW3GB include the 75 MHz maximum SPI clock frequency for fast firmware downloads, a 256-byte page with typical 0.8 ms page programming time, uniform 64-Kbyte sectors with 64 sectors total, and a deep power-down mode that reduces standby current to approximately 1 microamp. The device supports SPI modes 0 and 3, operates from a single 3.3 V supply, and offers hardware write protection on the /WP pin plus block-level software protection.
Architecturally, the M25P32 inherits the Numonyx/ST M25P family design later acquired by Micron, using floating-gate NOR cells with a state machine handling the standard SPI command set (READ, FAST_READ, PAGE PROGRAM, SECTOR ERASE, BULK ERASE, WRITE ENABLE/DISABLE, READ STATUS).JEDEC-standard 16-bit signatures allow electronic signature identification for programmer compatibility.
Typical applications include BIOS/firmware storage in automotive ECUs, boot code for FPGAs and microcontrollers, configuration storage in industrial drives and set-top boxes, and parameter logging in network equipment. Its AEC-Q100 qualification makes it a preferred choice for automotive temperature environments.
Design tip: use FAST_READ at 75 MHz only after verifying your PCB signal integrity; at high clock rates, keep traces short and add series termination on SCK.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: M25P32-VMW3GB — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: M25P32-VMW3GB (동일 폼 팩터 및 풋프린트) — 차이점: Memory Type, Packaging, Package, Write Protection, Supply Voltage.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
M25P32-VMW6TG
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
M25P32-VMW6GBA
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
M25P32-VMW3TPB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
M25P32-VME6G
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT25SF321B-SHB-T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
M25P32-VMW3GB 최대 정격 & 전기적 특성
| 메모리 유형 | NOR Flash, Serial SPI |
| Density | 32 Mbit (4M x 8) |
| 메모리 구성 | 4M x 8 |
| 인터페이스 | SPI, modes 0 and 3 |
| Max Clock Frequency | 75 MHz |
| 공급 전압 | 3.0 V to 3.6 V |
| Page Size | 256 bytes |
| Sector Size | 64 Kbytes (64 sectors) |
| 패키지 | 8-SOIC wide-body (VMW, 208 mil) |
| 실장 유형 | Surface Mount |
| Qualification | AEC-Q100 (automotive) |
| Write Protection | Hardware (/WP) and software block protection |
| Deep Power-Down | Supported, ~1 uA standby (per family datasheet) |
| Packaging | Tube |
M25P32-VMW3GB 핀 구성
| 핀 1 | /CS — Chip select (active low) |
| 핀 2 | DO — Serial data output (MISO) |
| 핀 3 | /WP — Write protect (active low) |
| 핀 4 | VSS — Ground |
| 핀 5 | DI — Serial data input (MOSI) |
| 핀 6 | SCK — Serial clock |
| 핀 7 | /HOLD — Hold (pause serial communication, active low) |
| 핀 8 | VCC — Power supply (3.0 V to 3.6 V) |
일반적인 애플리케이션
M25P32-VMW3GB 적합 용도: 6 애플리케이션s: Automotive ECU Firmware Storage, FPGA Configuration Storage, Industrial Automation Controllers, Set-Top Box and Consumer Electronics Boot Memory, Networking Equipment Parameter Storage, Battery-Powered and Deep-Sleep IoT Devices.
Automotive ECU Firmware Storage
The M25P32-VMW3GB is AEC-Q100 qualified, making it directly suited to storing boot code, firmware images, and calibration data in automotive electronic control units. Its 32 Mbit capacity comfortably holds bootloader plus application images for 32-bit MCUs, and the 75 MHz FAST_READ instruction shortens ECU boot time versus slower 20-33 MHz legacy serial flashes. The 64 uniform 64-Kbyte sectors allow A/B firmware banks with sector-level update granularity, while /WP-based hardware protection guards calibration sectors against corruption. Because the device is EOL, new automotive designs should dual-qualify the AT25SF321B; existing programs can continue consuming M25P32 last-time-buy stock with the same 8-SOIC footprint.
추천
FPGA Configuration Storage
FPGAs frequently boot from serial NOR flash; the M25P32-VMW3GB's 32 Mbit density covers mid-range FPGA bitstreams and the 75 MHz FAST_READ mode reduces configuration time compared to 33 MHz parts. The standard M25P command set (READ, FAST_READ) is natively supported by many FPGA configuration controllers and soft-core bootloaders - an Intel/Altera community thread documents exactly this usage with M25P32 devices on Xilinx-class boards, where the AT25SF321B is validated as a drop-in successor. Place the flash close to the FPGA with short SCK/DO traces to sustain 75 MHz reads, and use the /HOLD pin to share the SPI bus with other peripherals during configuration.
추천
Industrial Automation Controllers
Industrial PLCs, motor drives, and I/O modules need nonvolatile storage for firmware, parameter sets, and fault logs. The M25P32-VMW3GB offers 4 Mbytes organized as 64 eraseable 64-Kbyte sectors, letting designers separate protected firmware regions from frequently rewritten logging regions under software block protection. Its single 3.3 V supply integrates directly with industrial logic rails, and deep power-down (~1 uA) supports battery-backed modules. Endurance of the floating-gate NOR technology suits parameter updates at realistic industrial rates. Because sector erase takes on the order of seconds per 64-Kbyte block, firmware-update routines should copy to RAM, erase, then reprogram to avoid watchdog timeouts during field updates.
추천
Set-Top Box and Consumer Electronics Boot Memory
Set-top boxes, routers, and smart-home hubs store bootloader and firmware in SPI NOR flash, and the M25P32-VMW3GB's 32 Mbit capacity plus 75 MHz interface make boot times acceptable for consumer expectations. The SPI bus minimizes pin count on crowded main boards, and the wide-body 8-SOIC footprint is inexpensive to assemble. Software block protection prevents accidental corruption of the immutable boot region while allowing over-the-air updates to application sectors. Designers should budget a bulk-erase strategy: a full-chip BULK ERASE is slower than parallel sector erases, so update managers typically erase only changed sectors to minimize downtime during firmware upgrades.
추천
Networking Equipment Parameter Storage
Routers, switches, and optical modules use SPI NOR flash for MAC addresses, board serials, PHY configuration, and mini-OS boot code. The M25P32-VMW3GB's 64 sectors map naturally onto configuration slots with wear-leveling at sector granularity, and hardware /WP write protection can lock factory data permanently. The 3.0-3.6 V supply matches standard networking logic rails, and SPI modes 0/3 ensure compatibility with any CPU or CPLD bus master. At 75 MHz, a full 4-Mbyte image read completes in well under a second, enabling fast redundant-controller synchronization. Keep the device on a dedicated SPI chip select to isolate bus contention from management traffic.
추천
Battery-Powered and Deep-Sleep IoT Devices
IoT endpoints, metering nodes, and portable instruments combine an MCU with serial NOR flash for firmware and logged data. The M25P32-VMW3GB's deep power-down mode cuts standby current to roughly 1 uA per family datasheet figures, preserving battery life between wakeups, while 75 MHz FAST_READ lets the host retrieve data quickly during short active windows - a fast-read/quick-sleep duty cycle that minimizes average current. The 8-SOIC wide-body package is hand-assemblable for prototyping yet reel-compatible for volume. Designers should add a pull-up on /HOLD and gate the SPI clock so the flash never receives activity while the host sleeps, preventing accidental wake-up current.
추천
추천 제품 요약
엔지니어링 참조 데이터: M25P32-VMW3GB — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | M25P32-VMW6TG | M25P32-VMW6GBA | M25P32-VMW3TPB | AT25SF321B-SHB-T |
|---|---|---|---|---|---|
| Package | 8-SOIC wide-body (VMW, 208 mil) | 8-SOIC wide-body - same | 8-SOIC wide-body - same | 8-SOIC wide-body - same | 8-SOIC wide-body (208 mil) - same footprint |
| Brand | Micron Technology | Micron Technology | Micron Technology | Micron Technology | Renesas Electronics (Adesto) |
| Density | 32 Mbit (4M x 8) | 32 Mbit | 32 Mbit | 32 Mbit | 32 Mbit |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 2.7 V to 3.6 V |
| Sector Architecture | 64 x 64 Kbytes | 64 x 64 Kbytes | 64 x 64 Kbytes | 64 x 64 Kbytes | 4-Kbyte sub-sectors + 64-Kbyte sectors |
| Lifecycle Status | EOL (last-time-buy inventory) | EOL | EOL | EOL | Active (recommended successor) |
주요 차별점
- Automotive AEC-Q100 qualification (vs AT25SF321B-SHB-T)
- 75 MHz FAST_READ performance (vs M25P32-VMW6TG)
- Uniform 64-Kbyte sector architecture (vs AT25SF321B-SHB-T)
- Long-term supply security is the trade-off (vs AT25SF321B-SHB-T)
설계 노트
At the 75 MHz FAST_READ rate, treat the SPI bus as a transmission line problem: keep SCK and DO traces under ~10 cm, route them over a continuous ground plane, and add 22-33 ohm series resistors near the clock driver to damp ringing. If your layout cannot guarantee short traces, clock the interface at 33 MHz where FAST_READ timing margins are far more forgiving, or fall back to standard READ. Validate with an oscilloscope at the flash side, not just at the host.
Always pull /HOLD and /WP up to VCC (10k resistors are typical) unless actively used - a floating /HOLD can cause sporadic bus stalls, and a floating /WP may leave hardware protection in an undefined state. Respect the write-enable (WREN) command before every program or erase operation; the device self-clears WEL after each operation, which is a common cause of 'flash refuses to write' bugs in first-time drivers.
Use the DEEP POWER-DOWN (DPD) instruction for battery applications: entering DPD via command B9h and releasing via a dedicated CS toggle sequence reduces standby current to approximately 1 uA per family datasheet, versus tens of microamps in standby. Allow the release-to-again-ready delay (specified in the datasheet, on the order of tens of microseconds) before issuing the first command after DPD exit, or your initial READ may fail intermittently.
Because the M25P32 family is EOL per the Renesas/Micron conversion guide, add the AT25SF321B (Renesas) as a validated second source now rather than at end-of-project. The parts share the 8-SOIC footprint and core command set, but verify status-register bit definitions and deep-power-down behavior in your firmware abstraction layer so the swap is a build-time change, not a redesign.
규정 준수 정보
AEC-Q100 automotive qualification stated in distributor parametric listings (datasheets.com: 'automotive aec-q100'). RoHS/REACH status not stated in provided data - confirm on the Micron part catalog page.
