MC33079DT - Low-Noise Quad Op Amp | STMicroelectronics | Audio
부품 번호: MC33079DT ✓ 활성MC33079DT 개요
An operational amplifier is a voltage-gain circuit element used to amplify small signals while improving impedance characteristics. The MC33079 belongs to the low-noise operational-amplifier family within the broader linear-amplifier and signal-conditioning hierarchy. Its low-noise input stage is particularly useful when the amplified signal originates from microphones, pickups, sensors, or line-level audio sources.
The four internal amplifiers share a common supply architecture and are intended for low-voltage audio applications. Key performance characteristics include 4.5 nV/√Hz input-voltage noise and 15 MHz gain-bandwidth product. The 7 V/µs slew rate supports faster signal transitions, while the manufacturer reports very low distortion of 0.002%. These characteristics make the device suitable where low noise, bandwidth, and signal fidelity must coexist in a compact package.
MC33079DT is a general-purpose quad amplifier rather than a dedicated audio-output driver. Each amplifier includes the conventional non-inverting and inverting inputs, an output, and supply pins. The SOIC-14 package provides a practical surface-mount option for industrial and consumer audio boards, active crossovers, preamplifiers, mixers, and instrumentation. Its four-channel organization makes it suitable for multichannel systems requiring consistent amplifier performance.
Typical uses include microphone preamplification, line-level buffering, active equalization, audio summing, and low-level sensor amplification. Designers should select suitable input and feedback networks based on the required noise gain, bandwidth, and output swing. The signal source and load must also be checked against the device's supply-voltage and common-mode limits before layout begins.
For PCB implementation, place input and output paths to minimize parasitic capacitance and keep feedback resistors close to the relevant amplifier pins. Decoupling capacitors should be positioned near the supply pins, while analog and high-impedance traces should remain away from switching nodes. Stable feedback ratios and clean grounding are especially important when low-level audio noise must remain below the source's own noise floor.
This page combines the MC33079DT's documented noise, bandwidth, slew-rate, distortion, and package characteristics with application-focused guidance, pin-compatible replacement analysis, and practical PCB considerations for evaluating the amplifier in new or existing audio designs.
드롭인 대체품: MC33079DT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC33079DT (동일 폼 팩터 및 풋프린트) — 차이점: Gain-Bandwidth Product, Slew Rate.
MC33079DG
✅ 드롭인가격 문의
데이터시트 보기 →MC33079DR2G
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM837MX
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC3403DR
✅ 드롭인✓ 재고 있음
$0.4102 / 개
데이터시트 보기 →OPA1644A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC33079DT 최대 정격 & 전기적 특성
| Number of Amplifiers | 4 circuits |
| Input-Voltage Noise Density | 4.5 nV/√Hz |
| Gain-Bandwidth Product | 15 MHz |
| Slew Rate | 7 V/µs |
| Distortion | 0.002% |
| Primary Application | Low-noise audio amplification |
| 패키지 | 14-pin SOIC |
| 실장 유형 | Surface mount |
| Amplifier Architecture | Monolithic quad operational amplifier |
| Output Stage | Large output voltage swing |
| RoHS 상태 | unknown |
| REACH Status | unknown |
MC33079DT 14-pin soic 핀 구성 가이드
MC33079DT(14-pin soic 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC33079DT.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC33079DT 적합 용도: 6 애플리케이션s: Low-Level Audio Preamplification, Active Audio Equalization, Audio Mixing and Summing, Active Crossover Networks, Low-Level Sensor Signal Conditioning, Headphone and Line-Level Buffering.
Low-Level Audio Preamplification
The MC33079DT suits microphone, pickup, and line-level preamplification because its 4.5 nV/√Hz input-voltage noise limits the amplifier's contribution to low-level audio signals. Each of its four amplifiers can support a separate mono or balanced-difference input stage. The 15 MHz gain-bandwidth product gives designers margin for moderate closed-loop gains, while the 7 V/µs slew rate preserves large-signal transient performance. Feedback resistance and source impedance should be selected to balance noise gain against the usable bandwidth.
추천
Active Audio Equalization
The MC33079DT can implement first-order or higher-order active equalizer stages where low noise and moderate bandwidth are both important. Its four amplifiers provide a practical way to build dual-band or multi-channel tone controls without using four separate packages. The 4.5 nV/√Hz noise density helps preserve quiet passages, while the 15 MHz gain-bandwidth product allows useful closed-loop bandwidth at common audio gains. Component tolerances in the feedback and frequency-selective networks should be evaluated against the intended EQ curve.
추천
Audio Mixing and Summing
Four integrated amplifiers make the MC33079DT useful for compact audio mixers where several low-level sources must be summed before an ADC or power amplifier. Its low-voltage noise is beneficial when source amplitudes approach the noise floor, and the 15 MHz gain-bandwidth product provides more bandwidth than many audio-only stages require. Maintain compatible ground references across summing nodes, avoid excessive source loading, and verify the output swing for the chosen supply voltage and load.
추천
Active Crossover Networks
The MC33079DT is appropriate for active crossover designs requiring separate low-, mid-, and high-frequency channels. Its four amplifiers can implement buffered filter stages for a compact three-way system, and the 4.5 nV/√Hz noise density helps preserve low-level output from the crossover. The 7 V/µs slew rate and 15 MHz gain-bandwidth product provide useful headroom beyond the audible band, although component tolerances and filter topology determine actual channel matching.
추천
Low-Level Sensor Signal Conditioning
The MC33079DT can condition low-level sensor outputs when the required bandwidth is moderate and source noise must not be masked by amplifier noise. Its 4.5 nV/√Hz input-voltage noise is useful for resistive or capacitive sensors, while four channels permit compact instrumentation with several measurement paths. The design must account for input bias current, common-mode range, and sensor drive impedance. Those operating limits should be confirmed from the manufacturer electrical characteristics before selecting the amplifier.
추천
Headphone and Line-Level Buffering
The MC33079DT can buffer line-level signals or form the input stage of a headphone preamplifier when low noise and adequate drive capability are required. The 4.5 nV/√Hz input noise supports quiet audio reproduction, while the 7 V/µs slew rate helps reproduce transients without excessive distortion. Check output-current demand, voltage headroom, and stability with the intended load. A passive output attenuator may be needed if the amplifier cannot directly drive the selected impedance.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC33079DT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC33079DG | MC33079DR2G | LM837MX | MC3403DR | OPA1644A |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
주요 차별점
- Documented low-noise performance for four audio channels (vs MC33079DG)
- Higher documented bandwidth than a general-purpose audio alternative (vs MC3403DR)
- Fast documented slew rate for audio transients (vs LM837MX)
설계 노트
Place the MC33079DT input pins, feedback resistors, and compensation components close to the relevant amplifier pins. High-impedance audio inputs should be short and surrounded by a grounded guard where appropriate. Keep switching-regulator, digital-clock, and display traces away from the input nodes, because capacitive coupling into a 4.5 nV/√Hz amplifier can create audible interference even when the schematic appears electrically correct.
Route the supply connections directly to the package pins and place the manufacturer-recommended bypass capacitors on the PCB rather than at a distant power branch. Star-point grounding of analog return currents helps prevent output-current excursions in the ground network from modulating the input reference. Confirm the complete supply range and output-swing limits in the electrical characteristics before defining the minimum rail voltage for low-level operation.
Select closed-loop gain and feedback resistance together rather than optimizing bandwidth independently. Higher noise gain reduces the usable bandwidth and may require additional compensation or stability verification. Test each gain stage across expected source impedance, load, component tolerance, and temperature. For filters, calculate component tolerance sensitivity because the quad amplifier's bandwidth alone does not determine channel matching or cutoff accuracy.
규정 준수 정보
The MC33079DT is a general-purpose operational amplifier rather than an automotive-qualified device. Compliance declarations should be confirmed from the current STMicroelectronics product documentation before procurement.