MC9S08GB60ACFUE - 8-bit 40MHz 60KB Flash MCU | NXP | LQFP-64
부품 번호: MC9S08GB60ACFUE ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
MC9S08GB60ACFUE 개요
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program and data memory, and peripheral functions such as timers, serial interfaces, and analog-to-digital converters. Within the embedded-systems hierarchy, the S08GB60 belongs to the HCS08 family of the broader MC9S08 / Freescale-NXP 8-bit MCU lineage, positioned for cost-sensitive embedded control where CAN networking and moderate analog integration are required on a single device.
Key features include the integrated CAN 2.0 A/B controller (msCAN), two SCI (UART) interfaces, an SPI interface, an 8-channel 10-bit ADC, an internal oscillator option that reduces external component count, and an operating supply range of 1.8 V to 3.6 V. Per the NXP product page, the device integrates CAN, SPI, and SCI interfaces and was designed for automotive and industrial control applications.
The HCS08 core uses a CISC architecture with a rich instruction set, background debug mode (BDM) for non-intrusive flash programming and debugging, and low-power wait and stop modes. The 10-bit ADC supports sequential conversions across 8 multiplexed channels, suitable for sensor front-ends such as throttle position, temperature, and battery-voltage monitoring. The on-chip flash supports in-circuit reprogramming through the single-wire background debug interface.
Typical applications include automotive body electronics and gateway nodes, industrial control systems, motor control auxiliaries, and CAN-networked sensor modules, where the msCAN block provides a standards-based serial network without an external CAN controller.
Design consideration: this part is NRND (Not Recommended for New Designs) per NXP, so new designs should evaluate successor devices; existing designs should secure last-time-buy stock or qualify a drop-in family variant. The 1.8 V to 3.6 V supply range requires a regulated rail with adequate decoupling on all VDD/VSS pairs.
This page synthesizes distributor availability data, datasheet-derived specifications, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.
드롭인 대체품: MC9S08GB60ACFUE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC9S08GB60ACFUE (동일 폼 팩터 및 풋프린트) — 차이점: Package, Core Processor, RAM, ADC, RAM Size.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC9S08GB60CFU
✅ 드롭인✓ 재고 있음
$4.61 / 개
데이터시트 보기 →MC9S08GT60CFU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC9S08GB32CFU
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$4.1 / 개
데이터시트 보기 →MC9S08GT16CFBE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$4.65 / 개
데이터시트 보기 →MC9S08AW60CPUE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
가격 문의
데이터시트 보기 →MC9S08GB60ACFUE 최대 정격 & 전기적 특성
| Core Processor | HCS08 (8-bit CISC) |
| Core Size | 8-Bit |
| 최대 클록 주파수 | 40 MHz |
| Bus Clock Frequency | 20 MHz |
| Program Memory Size | 60KB (60K x 8) |
| Program Memory Type | FLASH |
| RAM Size | 4K x 8 |
| Supply Voltage (Vcc/Vdd) | 1.8V ~ 3.6V |
| Data Converters | A/D 8x10b |
| Connectivity | CAN, SPI, SCI (UART) |
| Oscillator Type | Internal |
| 동작 온도 | -40C ~ 85C (TA) |
| 패키지 | 64-LQFP (10x10 mm) |
| 실장 유형 | Surface Mount |
| Series | S08, S08GB |
| EEPROM Size | - |
MC9S08GB60ACFUE 64-lqfp (10x10 mm) 핀 구성 가이드
MC9S08GB60ACFUE(64-lqfp (10x10 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC9S08GB60ACFUE.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC9S08GB60ACFUE 적합 용도: 6 애플리케이션s: Automotive Body Electronics, Industrial Control Systems, CAN Bus Sensor Modules, Motor Control Auxiliary Logic, Battery-Powered Portable Instruments, Legacy Maintenance and Migration.
Automotive Body Electronics
The MC9S08GB60ACFUE was explicitly designed for automotive applications per NXP, and its integrated msCAN controller (CAN 2.0 A/B) lets body modules such as door controllers, seat adjusters, lighting modules, and climate flaps communicate on the vehicle network without an external CAN controller. The -40C to +85C A-grade temperature rating matches under-dash and engine-bay-adjacent environments, while the 1.8V to 3.6V supply range supports load-dump-protected 3.3V rails. The 8-channel 10-bit ADC reads switch stacks, position sensors, and battery sense lines directly, and the 60KB FLASH accommodates full diagnostic stacks including UDS/KWP-lite message handling. Designers should budget CAN transceiver delay and use the internal oscillator only where bus timing tolerance allows.
추천
Industrial Control Systems
In factory and process control, the MC9S08GB60ACFUE serves as a node controller reading sensors and driving actuators over CAN or SCI links. The 20 MHz bus delivers adequate headroom for PID loops executing at 1 kHz, and the 8-channel 10-bit ADC (approximately 10-bit resolution, sequential scan) digitizes 0-3.3V transducer outputs such as pressure and temperature. The 60KB FLASH supports protocol stacks, calibration tables, and firmware-update bootloaders, while 4KB RAM holds loop state and communication buffers. Because the part is NRND, industrial new designs should consider the S08DZ/S08DV families; existing installed-base maintenance can continue sourcing this device while stock lasts. Use external watchcrystal timing when precise UART baud rates are required across temperature.
추천
CAN Bus Sensor Modules
Distributed sensor modules - tilt, level, proximity, and environmental sensing - benefit from the MC9S08GB60ACFUE's combination of an on-chip 10-bit ADC and msCAN controller in one 64-pin device. The sensor front-end connects directly to ADC channels, and the module transmits scaled engineering units on the CAN bus at 125 kbps to 1 Mbps (per msCAN capability), with hardware acceptance filters offloading the CPU. The internal oscillator option can clock non-CAN logic while a crystal clocks the CAN baud-rate generator, reducing BOM cost. With 60KB FLASH, the module can store calibration coefficients and a bootloader for field updates over CAN. Power budget is dominated by bus activity; enable stop modes between messages to cut average current significantly in battery-backup modules.
추천
Motor Control Auxiliary Logic
The MC9S08GB60ACFUE works well as auxiliary supervisory logic around a power stage: sequencing, fault latching, current and voltage telemetry via the 10-bit ADC, and operator-interface tasks, while a dedicated driver or DSP handles the PWM inner loop. The 20 MHz HCS08 bus executes housekeeping and CAN reporting concurrently, and timer resources generate slow PWM channels for fans, relays, and indicator LEDs. Its 1.8V to 3.6V range allows operation from the same rail as gate-driver logic. Because the ADC result registers are directly accessible in the HCS08 memory map, telemetry sampling adds minimal overhead. Designers should route ADC sense lines away from gate-drive switching nodes and average multiple samples to reject switching noise.
추천
Battery-Powered Portable Instruments
Handheld meters, dataloggers, and portable test instruments leverage the MC9S08GB60ACFUE's low-voltage operation (1.8V to 3.6V) and HCS08 low-power modes. In stop mode the core and clocks halt, allowing wake from keyboard or RTC interrupts, and wait mode keeps peripherals running with the CPU idle - suitable for periodic ADC scans in a logging loop. The 60KB FLASH stores logged datasets, lookup tables, and a USB- or UART-based firmware updater, while 4KB RAM buffers sample streams. The internal oscillator eliminates a crystal in coarse-timing designs, trimming BOM cost and board area on the 10x10 mm LQFP layout. Battery life estimates must include flash-erase/write energy when logging frequently to flash emulation pages.
추천
Legacy Maintenance and Migration
A major ongoing use of the MC9S08GB60ACFUE is sustaining existing products: NXP's NRND status means no new designs, yet automotive and industrial fleets in the field still require service spares and running repairs. Procurement teams should quantify remaining lifetime demand, place last-time-buy orders while distributor stock exists (DigiKey and Mouser listed availability as of 2026-10-18), and qualify a migration path. Same-family drop-ins (MC9S08GB60CFU, S08GT60 variants) reuse the PCB and firmware; the S08DZ/S08DV families need layout changes but remain in production. Maintain the BDM programming fixture and CodeWarrior toolchain licenses, and archive the MC9S08GB60/D Rev. 2.3 data sheet and mask-set documentation for long-term support.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC9S08GB60ACFUE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC9S08GB60CFU | MC9S08GT60CFU | MC9S08GB32CFU | MC9S08GT16CFBE | MC9S08AW60CPUE |
|---|---|---|---|---|---|---|
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP - same footprint | 64-LQFP - same footprint |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Program Memory (FLASH) | 60KB | 60KB | 60KB | 32KB | 16KB | 60KB |
| CAN Module | Yes (msCAN, CAN 2.0 A/B) | Yes (msCAN) | No | Yes (msCAN) | No | No |
주요 차별점
- Integrated msCAN controller (vs MC9S08GT60CFU)
- Largest flash in the shared 64-LQFP footprint (vs MC9S08GB32CFU)
- Same-die family migration path (vs MC9S08GT16CFBE)
설계 노트
Supply the MC9S08GB60ACFUE from a regulated 3.3V rail within the 1.8V to 3.6V range. Decouple every VDD/VSS pin pair of the 64-LQFP with 100 nF ceramic capacitors placed within 2 mm of the pins, plus one 4.7 uF to 10 uF bulk capacitor near the package. Flash program/erase operations draw current pulses on VDD; undersupplied rails during flash writes cause write failures. If the CAN transceiver runs from 5V, level-shift RX/TX appropriately or choose a 5V-tolerant transceiver per its datasheet.
Provide the standard 6-pin (or 4-pin) BDM background debug header on every board, including production builds, for in-circuit flash programming of the HCS08 core. Keep the BKGD line short with a pull-up as specified in the MC9S08GB60/D data sheet. Route the CAN TX/RX to the transceiver with a series resistor (typically 10 to 100 ohm) to control edge rates and EMI. Reserve a crystal footprint even if the internal oscillator is used initially - UART baud accuracy and future CAN timing requirements often force a switch to crystal timing.
The device is NRND per NXP - do not start new designs on this part without a documented exit strategy. There is no dedicated EEPROM; flash-emulated parameter storage consumes endurance cycles, so wear-level writes across a 512-byte page sector and log erase counts. Analog readings suffer when switching nearby port outputs during ADC sampling - schedule conversions away from GPIO edges. Finally, verify the exact suffix decoding (ACFUE vs CFU) for temperature grade and packing before substitution; the orderable suffix encodes grading not visible from the base part number.
규정 준수 정보
Verified web data does not state RoHS/REACH/lead-free status for this exact ordering code. The NXP product page (nxp.com/part/MC9S08GB60ACFUE) lists Environmental Quality data; consult it or request a material declaration before regulated-market shipping. AEC-Q100 status not stated in provided data.