OPA177GS - Precision Low-Noise Op Amp | Texas Instruments
부품 번호: OPA177GS ✓ 활성OPA177GS 개요
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Precision operational amplifiers add low offset, low drift, high gain, and controlled noise to that basic function. The OPA177 belongs to the bipolar operational-amplifier family within the broader voltage-feedback amplifier and analog signal-processing categories, where accurate DC amplification is required without the periodic noise artifacts associated with chopper-stabilized amplifiers.
The main advantages of the OPA177GS are its low 10 µV maximum input offset voltage, 0.1 µV/°C maximum drift, 130 dB minimum open-loop gain, and 600 kHz gain-bandwidth product. Its 1.5 mA typical quiescent current supports low-power instrumentation, while the bipolar input architecture provides continuous signal transfer without the low-frequency chopping spikes found in some precision amplifiers. These characteristics allow small sensor outputs and measurement errors to be amplified without introducing excessive DC error.
OPA177 performance depends on maintaining high open-loop gain around the operating signal and keeping input-offset errors small relative to the sensed voltage. The manufacturer identifies the device as a low-noise bipolar precision amplifier and an effective alternative to chopper-stabilized products. Its signal-integrity advantage is particularly useful when low-frequency noise, sudden output disturbances, restricted common-mode range, or external storage capacitors would be undesirable in the measurement path.
Typical uses include precision instrumentation, bridge and transducer signal conditioning, laboratory measurement systems, low-level current sensing, and high-resolution data-acquisition front ends. In each case, the amplifier can sit close to the sensor to minimize interference pickup before the signal is amplified. The device is also appropriate for buffering applications where input bias current and DC accuracy are more important than wide bandwidth.
PCB layout is critical because thermoelectric voltages at dissimilar-metal connections can degrade offset and drift performance. Keep input traces short, avoid current paths through input-node copper, use symmetric routing, and establish a quiet ground reference. For sensitive measurements, use clean supplies, stable reference components, and decoupling placed close to the supply pins rather than relying on long supply traces.
This product page combines the manufacturer ordering information, package identification, verified parametric highlights, legacy cross-reference results, and application-specific engineering guidance. It also distinguishes true same-footprint alternatives from related amplifier options and highlights the layout practices needed to preserve the OPA177GS low-offset, low-drift performance in a completed circuit.
드롭인 대체품: OPA177GS — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA177GS (동일 폼 팩터 및 풋프린트) — 차이점: Input Offset Voltage, Package, Amplifier Type, Input Bias Current, Open-Loop Gain.
OPA177UA
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
OP177GSZ
✅ 드롭인가격 문의
데이터시트 보기 →OP177GSZ
✅ 드롭인가격 문의
데이터시트 보기 →OP07CSZ
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA177GS 최대 정격 & 전기적 특성
| Amplifier Type | Single-circuit precision bipolar operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 600 kHz |
| Input Offset Voltage | 10 µV maximum |
| Input Offset Drift | 0.1 µV/°C maximum |
| Open-Loop Gain | 130 dB minimum |
| 대기 전류 | 1.5 mA typical |
| 패키지 | 8-pin SOIC |
| 실장 유형 | Surface mount |
| RoHS 상태 | Compliant |
| MSL | Level 3, 260°C, 168 hours |
OPA177GS 핀 구성
| 핀 1 | OFFSET NULL — Offset-voltage null input |
| 핀 2 | IN- — Inverting input |
| 핀 3 | IN+ — Non-inverting input |
| 핀 4 | V- — Negative supply connection |
| 핀 5 | OFFSET NULL — Offset-voltage null input |
| 핀 6 | OUT — Amplifier output |
| 핀 7 | V+ — Positive supply connection |
| 핀 8 | NC — Not connected |
일반적인 애플리케이션
OPA177GS 적합 용도: 6 애플리케이션s: Precision Data-Acquisition Front Ends, Bridge and Transducer Signal Conditioning, Low-Level Current Measurement, Laboratory Buffering and Gain Stages, High-Resolution Analog Signal Conditioning, Precision Control and Measurement Loops.
Precision Data-Acquisition Front Ends
The OPA177GS fits low-level sensor and laboratory acquisition chains because its 10 µV maximum offset voltage and 0.1 µV/°C maximum drift limit DC error relative to small measured signals. A 600 kHz gain-bandwidth product provides useful bandwidth for low-frequency laboratory channels without requiring a high-speed amplifier. Place the device close to the source, use short input traces, and preserve a symmetrical thermal layout. The 1.5 mA typical quiescent current also helps limit self-heating when several precision channels are packed into an instrument.
추천
Bridge and Transducer Signal Conditioning
OPA177GS is appropriate for bridge outputs and low-level transducers where the useful signal is much smaller than the supply voltage. Its 130 dB minimum open-loop gain supports accurate amplification in a feedback stage, while the 0.1 µV/°C maximum drift helps stabilize the measurement as ambient temperature changes. Differential-input layouts should keep both amplifier inputs on similar copper and thermal paths to reject temperature gradients and thermoelectric voltages. The design must also provide input filtering that avoids excessive differential noise amplification.
추천
Low-Level Current Measurement
OPA177GS can amplify the small voltage produced by a current-sensing element when DC accuracy is more important than wide bandwidth. The 600 kHz gain-bandwidth product covers many control, meter, and laboratory current-measurement channels, while low offset and drift reduce error near zero current. Place the amplifier adjacent to the sense element to minimize pickup and use a Kelvin connection where practical. Verify that the selected sense resistor, amplifier gain, and common-mode operating range remain valid over the measured current and supply range.
추천
Laboratory Buffering and Gain Stages
OPA177GS provides a straightforward voltage buffer or fixed-gain stage for laboratory instruments where continuous low-noise behavior is preferred over the very low offset of a chopper-stabilized amplifier. The 1.5 mA typical quiescent current is suitable for portable and multi-channel bench equipment, and the bipolar architecture avoids characteristic low-frequency chopping disturbances. Use clean references, stable feedback resistors, and supply bypassing close to the device. Keep the feedback loop compact and avoid routing output currents close to input nodes.
추천
High-Resolution Analog Signal Conditioning
OPA177GS is suited to conditioning signals for high-resolution converters when converter input accuracy is limited by amplifier offset, drift, or noise. The low 10 µV maximum offset, 0.1 µV/°C maximum drift, and 600 kHz bandwidth provide a practical balance between DC precision and usable signal speed. The amplifier should drive the converter through an appropriate RC isolation network, with resistance and capacitance selected to suppress sampling transients without adding excessive noise. Confirm the converter’s input range and settling requirements during system validation.
추천
Precision Control and Measurement Loops
OPA177GS can serve as a feedback amplifier in slow industrial or laboratory control loops where high DC gain and predictable thermal behavior are valuable. Its 130 dB minimum open-loop gain and low offset drift support accurate setpoint tracking, while 600 kHz bandwidth is adequate for many low-bandwidth loops. Compensation must be checked with the actual sensor, cables, and load because added poles can reduce phase margin. Use a grounded, low-impedance reference and route high-current outputs away from sensitive measurement nodes.
추천
추천 제품 요약
엔지니어링 참조 데이터: OPA177GS — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA177UA | OP177GS | OP177GSZ | OP07CSZ |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Configuration | Single-channel operational amplifier | Single-channel operational amplifier | Single-channel operational amplifier | Single-channel operational amplifier | Single-channel precision operational amplifier |
| Primary Application | Precision instrumentation and data acquisition | Precision instrumentation and data acquisition | Precision instrumentation | Precision instrumentation | Precision instrumentation |
주요 차별점
- Low-noise continuous bipolar signal path (vs OP07CSZ)
- Low DC offset and temperature drift (vs OP177GS)
- Same-footprint upgrade path with current TI documentation (vs OPA177UA)
설계 노트
Keep both OPA177GS input traces short and symmetric, and avoid routing them beside switching nodes, relay contacts, or high-current return paths. Thermoelectric voltages caused by connections between dissimilar metals can degrade offset voltage and drift. Use matched copper paths where possible, keep the amplifier close to the source, and avoid resistive or leakage paths between the input pins and ground.
Place power-supply bypass capacitance close to the V+ and V- pins and connect the return directly to the appropriate ground plane. Keep sensitive feedback components and their ground returns away from noisy power-conversion components. Before finalizing the layout, verify the complete input, feedback, supply, and ground network for oscillation using the actual source impedance and load capacitance.
OPA177GS offers 600 kHz gain-bandwidth product, so the useful closed-loop bandwidth depends on the selected noise gain and stability requirements. Add input or output isolation only when needed to control capacitive loading, and evaluate the resulting bandwidth and noise penalty. Do not assume the full gain-bandwidth product is available in every gain configuration or with arbitrary load capacitance.
규정 준수 정보
RoHS compliance and MSL Level 3, 260°C, 168-hour information are identified for OPA177GS. Other compliance declarations were not confirmed.