OPA337UA - 5.5V 3MHz RRO Op Amp | Texas Instruments
부품 번호: OPA337UA ✓ 활성OPA337UA 개요
An operational amplifier is an analog building block that amplifies the voltage difference between its two inputs. OPA337UA uses a CMOS implementation, placing it within the hierarchy of linear amplifiers, voltage amplifiers, analog signal-conditioning ICs, and semiconductor devices. Its rail-to-rail output capability allows the output signal to approach the available supply limits, which is especially useful when signal headroom is limited.
The principal device characteristics include one amplifier channel, a maximum supply voltage of 5.5 V, a 3 MHz gain-bandwidth product, rail-to-rail output operation, and an 8-pin SOIC package. According to the Texas Instruments OPA337 product page, the OPA337 and OPA338 series uses advanced CMOS technology and is intended for compact, low-cost applications. These characteristics make the device suitable for sensor interfaces, low-side or general-purpose analog conditioning, ADC driver stages, and embedded portable equipment.
OPA337UA belongs to a family of micro-size CMOS operational amplifiers offered in multiple package configurations. The series description emphasizes rail-to-rail output performance, low-voltage operation, and small physical size. A 3 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while the single amplifier arrangement avoids the need to allocate a second channel when the application requires only one signal path. Detailed offset, bias-current, noise, slew-rate, common-mode, and thermal limits must be confirmed in the manufacturer datasheet before final circuit sign-off.
Typical applications include buffering sensor outputs, conditioning analog signals for ADC inputs, amplifying low-level control signals in industrial systems, and providing local gain in portable or space-constrained systems. It can also support interface and monitoring functions where a single low-voltage amplifier provides sufficient bandwidth and output range. The 8-pin SOIC footprint is convenient for conventional surface-mount PCB assembly.
Designers should verify the exact input common-mode range, output swing, gain stability, and supply-voltage limits against the circuit operating conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be kept away from switching-current paths. Because the available public listing confirms the package and headline specifications but does not provide the complete electrical-characteristic table, those detailed values require consultation of the TI datasheet.
This product record combines the confirmed OPA337UA identity and packaging information with a focused engineering comparison of qualified drop-in options, application guidance, and design considerations. It helps buyers distinguish package-compatible alternatives from broader functional equivalents while keeping the final component selection grounded in the manufacturer's published device information.
드롭인 대체품: OPA337UA — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: OPA337UA (동일 폼 팩터 및 풋프린트) — 차이점: Gain-Bandwidth Product, Package, Amplifier Type, Number of Channels, Mounting Type.
OPA338UA
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →OPA336UA
✅ 드롭인가격 문의
데이터시트 보기 →TLV2371QDBVRQ1
✅ 드롭인가격 문의
데이터시트 보기 →MCP6001
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA337UA 최대 정격 & 전기적 특성
| Amplifier Type | Single operational amplifier |
| Number of Channels | 1 circuit |
| Technology | CMOS |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 3 MHz |
| Output Swing | Rail-to-rail output |
| 패키지 | 8-pin SOIC |
| 실장 유형 | Surface mount |
| Product Series | MicroAmplifier series |
OPA337UA 8-pin soic 핀 구성 가이드
OPA337UA(8-pin soic 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: OPA337UA.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
OPA337UA 적합 용도: 6 애플리케이션s: Low-Voltage Sensor Signal Conditioning, Portable Analog Measurement Front End, ADC Input Driver, RS-232 Interface Support, Industrial Control and Monitoring, Compact Analog Signal Buffer.
Low-Voltage Sensor Signal Conditioning
OPA337UA fits low-voltage sensor interfaces that need local amplification before conversion or control. Its single CMOS channel, 3 MHz gain-bandwidth product, and rail-to-rail output provide useful bandwidth and signal range for sensors operating from a supply no higher than 5.5 V. Place the amplifier close to the sensor connector to limit noise pickup, then verify the sensor output range against the amplifier's input common-mode capability. The rail-to-rail output is valuable when the downstream converter accepts signals near the available supply range. Selection must also account for input offset, bias current, noise, output drive, and capacitive-load stability, which are not stated in the accessible product summary and should be confirmed from the manufacturer datasheet.
추천
Portable Analog Measurement Front End
OPA337UA is appropriate for portable instruments that combine a low-voltage sensor, a local gain stage, and an ADC. Its 5.5 V maximum supply rating supports compact single-supply systems, while the 3 MHz gain-bandwidth product can handle moderate-frequency analog signals without requiring a high-speed discrete amplifier family. A practical arrangement places the amplifier in a non-inverting or inverting gain block near the sensor and analog converter. Engineers should check offset drift, bias-current error, noise, and output settling against the measurement bandwidth. PCB layout should preserve a low-noise ground reference and short feedback paths so that connector and switching-supply disturbances do not dominate the small signals produced by portable sensors.
추천
ADC Input Driver
OPA337UA can serve as an ADC driver when the target converter needs gain, level translation, or isolation from a high-impedance sensor. The 3 MHz gain-bandwidth product supports many moderate-speed acquisition paths, and the rail-to-rail output provides flexibility when the ADC input range extends near a 5 V supply rail. Confirm the ADC's input range, sampling rate, settling requirements, and kickback behavior before setting the amplifier gain. The feedback network should be placed close to the amplifier pins, and the output route to the ADC should avoid crossing digital return currents. Decoupling and output isolation are especially important when the converter contains a sampling capacitor because the resulting switching transients can otherwise disturb the signal and distort conversion results.
추천
RS-232 Interface Support
OPA337UA can support low-voltage interface circuitry around a modern RS-232 transceiver, particularly where a small-signal level shift, receiver conditioning, or auxiliary amplifier function is required. The device's 3 MHz bandwidth is substantially above the signaling rate of a conventional serial interface, and its rail-to-rail output can operate from a 5 V-oriented supply. It does not replace the RS-232 line driver or protection network; it should be used only where the specific interface architecture calls for it. Verify the transceiver's supply rating, input thresholds, and logic levels, and confirm the amplifier's output swing and slew rate against the intended data rate. Keep the amplifier away from the high-energy line-side interface network to minimize surge-related coupling into sensitive control circuitry.
추천
Industrial Control and Monitoring
OPA337UA fits compact industrial monitoring blocks where a controller requires a buffered analog command or measurement signal. Its CMOS implementation, 5.5 V maximum supply capability, and 3 MHz gain-bandwidth product allow operation in low-voltage embedded control systems. The amplifier can buffer a sensor output, scale a potentiometer signal, or provide local gain before an ADC input. Because industrial environments can contain fast switching equipment, the design should minimize loop area and keep sensitive analog traces away from motor and relay return paths. Confirm the operating temperature range, noise performance, and output behavior under the required load before production use. A solid ground reference, local bypass capacitance, and conservative output loading are essential for maintaining predictable behavior in a control enclosure.
추천
Compact Analog Signal Buffer
OPA337UA is useful as a compact unity-gain or moderate-gain buffer when a high-impedance source cannot directly drive the following stage. The single-amplifier configuration minimizes component count, while the 3 MHz bandwidth provides margin for low-frequency and moderate-bandwidth precision signals. The rail-to-rail output can improve usable signal range in low-voltage systems, although the actual output swing under load must be confirmed from the datasheet. Place the amplifier near the source or load being buffered to avoid long high-impedance traces that increase noise pickup. Check bias-current error, offset voltage, capacitive-load behavior, and stability at the intended closed-loop gain before finalizing the circuit, particularly when driving sampling inputs, long cables, or unusually large capacitances.
추천
추천 제품 요약
엔지니어링 참조 데이터: OPA337UA — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA338UA | OPA336UA | TLV2371 | MCP6001 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Application Class | General-purpose precision signal conditioning | General-purpose CMOS signal conditioning | Precision CMOS signal conditioning | Low-voltage operational amplification | Low-voltage CMOS operational amplification |
| SOA | Not applicable | Not applicable | Not applicable | Not applicable | Not applicable |
주요 차별점
- Confirmed 3 MHz bandwidth in the selected OPA337 family configuration (vs MCP6001)
- Single-supply operation with a 5.5 V maximum rating (vs TLV2371)
- Rail-to-rail output confirmed for the OPA337 and OPA338 series (vs OPA336UA)
- Same-manufacturer MicroAmplifier family alignment (vs MCP6001)
설계 노트
Place the manufacturer-recommended bypass capacitors directly beside the OPA337UA supply and ground pins. Keep feedback resistors and their associated traces close to the amplifier to minimize parasitic capacitance and reduce susceptibility to EMI. For sensor or ADC interfaces, route the sensitive input directly to the relevant pin and avoid sharing narrow return paths with switching converters, relay coils, or digital processor outputs.
Validate stability with the actual source impedance, gain setting, output load, and PCB capacitance. OPA337UA's 3 MHz gain-bandwidth product is suitable for many moderate-frequency paths, but the complete datasheet must be used to select gain and isolation components. If the amplifier drives an ADC sampling input or a capacitive cable, place a small isolation resistor at the output and verify settling and overshoot with the intended load.
Do not assume that every SOIC-8 amplifier is pin-compatible with OPA337UA. Check the package drawing, pin names, input configuration, supply pins, and enable or shutdown functions for every proposed replacement. Also confirm that the alternative's input common-mode range covers the sensor or source voltage and that its output can reach the required load level within the 5.5 V maximum supply condition.
OPA337UA's low 5.5 V maximum supply normally limits internal dissipation in ordinary signal-conditioning circuits, but the exact calculation depends on output voltage, load current, quiescent current, and package thermal resistance. Use the manufacturer power-dissipation equation with the worst-case supply and output states. Provide continuous copper around the SOIC footprint and avoid enclosing the device in a thermally isolated location when it operates near its maximum rated ambient temperature.
규정 준수 정보
The accessible manufacturer and distributor product information does not state a target-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration. AEC-Q100 qualification is not indicated and is not applicable unless the exact ordered configuration is separately qualified.