PIC16LC782T-I/SO - 8-Bit 20MHz 3.5KB OTP MCU | Microchip
부품 번호: PIC16LC782T-I/SO ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $5.42 | $5.42 |
| 10 | $4.88 | $48.80 |
| 100 | $3.95 | $395.00 |
| 500 | $3.21 | $1,605.00 |
| 1,000 | $2.74 | $2,740.00 |
PIC16LC782T-I/SO 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals such as ADC, DAC, timers, and communication interfaces into one package. PIC16 devices sit at the low pin-count, low-power end of Microchip's PIC architecture hierarchy (PIC10/16 -> mid-range 8-bit PIC -> 8-bit MCU -> microcontroller -> semiconductor). The PIC16LC782 specifically targets analog-rich mixed-signal designs by integrating both an 8-bit Analog-to-Digital Converter (ADC) with up to 8 input channels and an 8-bit Digital-to-Analog Converter (DAC) with one output channel on-chip.
Key features include 20MHz CPU clock, 16 digital I/O lines, an integrated 8-channel 8-bit ADC, an 8-bit DAC with output buffer, dual analog comparators, a 16-bit timer/counter with capture/compare/PWM, a USART/SCI module, and an internal bandgap voltage reference. The 'LC' prefix designates a low-power CMOS variant operating over 2.5V to 5.5V, while the 'T' suffix denotes Tape & Reel packaging. The OTP program memory allows one-time field programming via standard PIC programmers, with code retention rated for typical industrial lifetimes.
Architecturally, the device uses a 14-bit instruction word RISC core with a two-stage pipeline, an accumulator-based ALU, and Harvard-style separate program and data buses. The integrated analog peripherals are designed for closed-loop control loops where the ADC samples a sensor, a control algorithm runs on the CPU, and the DAC outputs an analog control voltage - eliminating the need for a separate analog front-end IC.
Typical applications include SMPS primary-side control (where the on-chip DAC programs the reference), closed-loop fan/lighting control, sensor conditioning front-ends, small consumer appliances, and any cost-sensitive embedded design needing both digital logic and analog trim/servo control. The 20-pin SOIC footprint is the most common PIC16 footprint, simplifying hand prototyping and breadboard-friendly adapter boards.
When designing with this part, note that OTP memory cannot be re-programmed in-circuit - choose the flash-based PIC16F or PIC16LF equivalent family for field-updatable firmware. The LC variant runs 3.3V at 20MHz; confirm headroom at 5V with the speed/frequency characteristic of the specific OTP bit cell generation.
This page synthesizes distributor pricing, drop-in OTP and flash alternatives, and practical analog-mixed-signal design notes not found in the manufacturer datasheet.
드롭인 대체품: PIC16LC782T-I/SO — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16LC782T-I/SO (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, Operating Temperature, Program Memory Type, Timers.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16LC782-I/SO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16LC781-I/SO
✅ 드롭인✓ 재고 있음
$2.46 / 개
데이터시트 보기 →PIC16LC717-I/SO
✅ 드롭인✓ 재고 있음
$2.85 / 개
데이터시트 보기 →PIC16LC773-I/SO
✅ 드롭인✓ 재고 있음
$5.95 / 개
데이터시트 보기 →PIC16LC717T-I/SO
✅ 드롭인✓ 재고 있음
$1.72 / 개
데이터시트 보기 →PIC16LC770-E/SO
✅ 드롭인✓ 재고 있음
$4.4 / 개
데이터시트 보기 →PIC16LC782T-I/SO 최대 정격 & 전기적 특성
| Manufacturer | Microchip Technology |
| Series | PIC 16C |
| Core | 8-bit PIC RISC |
| Core Size | 8-bit |
| CPU Speed | 20 MHz |
| Program Memory | 3.5 KB (2K x 14) OTP |
| Data RAM | 128 x 8 bytes |
| I/O Pins | 16 |
| ADC | 8-bit, 8 channels |
| DAC | 8-bit, 1 channel |
| 패키지 | 20-SOIC (0.295, 7.50mm width) |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40C to +85C (Industrial) |
| 공급 전압 | 2.5V to 5.5V (LC low-power variant) |
| Packaging | Tape & Reel (TR) |
| Moisture Sensitivity Level | 1 (Unlimited) |
| Time @ Peak Reflow | 40 s max |
PIC16LC782T-I/SO 핀 구성
| 핀 1 | RA2/AN2 — GPIO / Analog input channel 2 |
| 핀 2 | RA3/AN3 — GPIO / Analog input channel 3 |
| 핀 3 | RA4/AN4 — GPIO / Analog input channel 4 |
| 핀 4 | RA5/AN5 — GPIO / Analog input channel 5 |
| 핀 5 | VDD — Positive supply voltage (2.5V to 5.5V) |
| 핀 6 | VSS — Ground reference |
| 핀 7 | OSC1 — Oscillator input / external clock input |
| 핀 8 | OSC2 — Oscillator output / clock out |
| 핀 9 | RC0 — GPIO / timer I/O |
| 핀 10 | RC1 — GPIO / timer I/O |
| 핀 11 | RC2 — GPIO / timer I/O |
| 핀 12 | RC3 — GPIO / timer I/O |
| 핀 13 | RC4 — GPIO / USART I/O |
| 핀 14 | RC5 — GPIO / USART I/O |
| 핀 15 | RC6 — GPIO / USART TX / serial clock |
| 핀 16 | RC7 — GPIO / USART RX / serial data |
| 핀 17 | RB0/INT — GPIO / external interrupt input |
| 핀 18 | RB1 — GPIO |
| 핀 19 | RB2 — GPIO |
| 핀 20 | MCLR/VPP — Master clear reset (active low) / programming voltage input |
일반적인 애플리케이션
PIC16LC782T-I/SO 적합 용도: 6 애플리케이션s: SMPS Primary-Side Control, Closed-Loop Fan / Lighting Control, Sensor Conditioning Front-End, Small Consumer Appliance Control, Battery-Powered Analog Trim & Calibration, Automotive Body Electronics (non-safety).
SMPS Primary-Side Control
The PIC16LC782T-I/SO is purpose-built for switch-mode power supply primary-side control, where its integrated 8-bit DAC programs the current/voltage reference and the on-chip 8-bit ADC samples the feedback loop at up to 20MHz CPU bandwidth. The internal bandgap reference and dual analog comparators enable peak current mode control topologies in isolated and non-isolated flyback converters.
추천
Closed-Loop Fan / Lighting Control
With 16 GPIO pins, an 8-bit DAC output, and 8-channel ADC inputs, the PIC16LC782T-I/SO drives closed-loop fan RPM and LED lighting control with on-chip PID computation and analog PWM generation. The 2.5V to 5.5V supply range supports direct connection to 3.3V or 5V fan tachometers and LED driver feedback paths without level shifters.
추천
Sensor Conditioning Front-End
The PIC16LC782T-I/SO acts as a digital sensor conditioner, sampling up to 8 analog sensor channels via the 8-bit ADC, applying linearization or compensation in firmware, and re-driving a corrected analog output through the on-chip 8-bit DAC. Industrial -40C to +85C rating and 20MHz CPU make it suitable for factory-floor sensor modules and HVAC transducers.
추천
Small Consumer Appliance Control
Consumer appliances such as coffee makers, blenders, and hair dryers benefit from the PIC16LC782T-I/SO's combination of 3.5KB OTP for fixed function firmware, 8-bit DAC for heater/triac drive, and 8-bit ADC for temperature/proximity sensing. The 20-SOIC package enables single-sided PCB assembly, lowering BOM and manufacturing cost for high-volume products.
추천
Battery-Powered Analog Trim & Calibration
The low-power CMOS 'LC' variant runs down to 2.5V, allowing the PIC16LC782T-I/SO to operate directly from a single lithium cell or two AA batteries while still driving the 8-bit DAC for calibration trim. Low quiescent current and the ability to wake from sleep on ADC interrupt make it ideal for infrequent analog calibration tasks in field instruments and IoT sensor nodes.
추천
Automotive Body Electronics (non-safety)
While not AEC-Q100 qualified, the PIC16LC782T-I/SO industrial -40C to +85C rating makes it suitable for non-safety automotive body modules such as seat position memory, mirror trim, and ambient lighting where its 8-bit DAC and 16 GPIO suffice. The integrated analog peripherals eliminate external trim DACs, reducing PCB area and BOM cost per node.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16LC782T-I/SO — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16LC782-I/SO | PIC16LC781-I/SO | PIC16LC717-I/SO | PIC16LC773-I/SO | PIC16LC770-E/SO |
|---|---|---|---|---|---|---|
| Package | 20-SOIC (7.50mm) | 20-SOIC (7.50mm) - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same | 20-SOIC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 3.5 KB (2K x 14) OTP | 3.5 KB OTP | ~3.5 KB OTP | ~2 KB OTP | 4 KB OTP | ~2 KB OTP |
| Data RAM | 128 x 8 bytes | 128 bytes | 128 bytes | 128 bytes | 256 bytes | 128 bytes |
| ADC | 8-bit, 8 channels | 8-bit, 8 ch | 8-bit, 8 ch | 8-bit, 6 ch | 12-bit, 8 ch | 8-bit, 6 ch |
| DAC | 8-bit, 1 channel | 8-bit, 1 ch | 8-bit, 1 ch | None | None | None |
| CPU Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| I/O Pins | 16 | 16 | 16 | 16 | 16 | 16 |
| Supply Voltage | 2.5V to 5.5V | 2.5V to 5.5V | 2.5V to 5.5V | 2.5V to 5.5V | 2.5V to 5.5V | 2.5V to 5.5V |
주요 차별점
- Integrated 8-bit DAC eliminates external trim DAC (vs PIC16LC717-I/SO)
- Larger OTP memory than 717/770 family siblings (vs PIC16LC770-E/SO)
- More capable ADC channel count than flash equivalents (vs PIC16LC773-I/SO)
설계 노트
The PIC16LC782T-I/SO requires a stable 2.5V to 5.5V supply with adequate bulk decoupling (10uF electrolytic + 0.1uF ceramic) placed within 1cm of VDD/VSS pins. The on-chip ADC is sensitive to supply ripple; for mixed-signal designs use a ferrite bead or LC filter between the digital VDD and analog AV-DD rail if present. Add a 100nF decoupling cap directly at each VDD pin pair to suppress switching transients from GPIO toggling.
OTP (One-Time-Programmable) memory cannot be re-programmed in-circuit. Engineers used to flash-based PIC16F parts must not assume firmware revisions are possible - plan firmware updates by physically swapping the MCU, or choose a flash-based PIC16F equivalent from the start. Verify the device ID and silicon revision match the expected die generation before programming; OTP programming voltages (VPP ~13V on MCLR) must be sequenced correctly to avoid permanent damage.
Route the analog ADC inputs (RA0-RA5, AN0-AN7) away from digital switching lines and clock traces to minimize coupled noise; place a ground guard ring around sensitive analog traces if board space allows. The on-chip 8-bit DAC output should be buffered if driving low-impedance loads (<10k ohm), as the integrated DAC has limited drive strength. Keep OSC1/OSC2 traces short and symmetric; long oscillator traces cause timing jitter and unreliable ADC conversions at 20MHz.
규정 준수 정보
RoHS, REACH, lead-free, halogen-free, and conflict-mineral status not present in the verified web data; verify against Microchip's material declaration before placing this part in a compliance-restricted design. Not AEC-Q100 qualified - the industrial -40C to +85C rating is not equivalent to automotive qualification.
