PIC18LF2680-I/SO - 8-bit 40MHz 64KB Flash MCU with ECAN | Microchip
부품 번호: PIC18LF2680-I/SO ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $7.85 | $7.85 |
| 10 | $7.1 | $71.00 |
| 100 | $6.32 | $632.00 |
| 500 | $5.68 | $2,840.00 |
| 1,000 | $5.05 | $5,050.00 |
PIC18LF2680-I/SO 개요
An 8-bit microcontroller (MCU) is a programmable processor that executes instructions on 8-bit data words, integrating CPU, memory (Flash for program, SRAM for variables), and peripherals onto one chip. Microcontrollers sit below microprocessors in the embedded hierarchy: MCU = microprocessor core + memory + peripherals in a single IC, optimized for control rather than raw compute. Within Microchip's portfolio, the PIC18F family occupies the high-performance 8-bit tier, and the PIC18F26xx sub-family specifically adds an integrated CAN 2.0B controller for automotive and industrial networking.
Key features include hardware ECAN 2.0B with acceptance filters, 10-bit ADC up to 8 channels, enhanced USART, MSSP (SPI/I2C), two analog comparators, and nanoWatt technology power management. The 64KB Flash is organized as 32K x 16 words, allowing word-aligned access. An ICD/ICSP debug port is provided for in-circuit development with MPLAB tools.
Typical applications include automotive body and comfort ECAN nodes, industrial sensor buses, HVAC controllers, building automation, and CAN-based battery management. The 28-SOIC footprint provides a wide, easy-to-solder outline well-suited to hand-prototyping and through-air rework.
When designing with this part, mind the 2.0V minimum VDD for LF operation, and ensure ECAN bus termination (120 ohm at each end) and proper transceiver selection such as MCP2551 or MCP2561.
드롭인 대체품: PIC18LF2680-I/SO — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18LF2680-I/SO (동일 폼 팩터 및 풋프린트) — 차이점: Package, Operating Temperature, Timers, Mounting Type, ADC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F2680-I/SO
✅ 드롭인✓ 재고 있음
$5.62 / 개
데이터시트 보기 →PIC18F2680-E/SO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18LF2680T-I/SO
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.21 / 개
데이터시트 보기 →PIC18F2610-I/SO
✅ 드롭인✓ 재고 있음
$3.95 / 개
데이터시트 보기 →PIC18F2580-I/SO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18LF2680-I/SO 최대 정격 & 전기적 특성
| Core | PIC18F 8-bit RISC |
| Program Memory | 64 KB Flash (32K x 16 words) |
| Data Memory (RAM) | 3328 bytes |
| Maximum CPU Frequency | 40 MHz |
| Operating Voltage (VDD) | 2.0 V to 5.5 V (LF variant) |
| 동작 온도 | -40C to +85C (industrial, "I" grade) |
| 패키지 | 28-pin SOIC (300 mil, "SO") |
| 실장 유형 | Surface Mount |
| CAN Controller | ECAN 2.0B active with acceptance filters |
| UART | 1x Enhanced USART (EUSART) |
| SPI | Yes (via MSSP) |
| I2C | Yes (via MSSP, Master/Slave) |
| Comparators | 2 analog comparators |
| ICSP/ICD Debug | Yes |
| RoHS 상태 | Compliant |
PIC18LF2680-I/SO 핀 구성
| 핀 1 | MCLR/VPP — Master Clear (active low) / ICSP programming voltage |
| 핀 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| 핀 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| 핀 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| 핀 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| 핀 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 핀 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| 핀 8 | VSS — Ground reference |
| 핀 9 | OSC1/CLKI/RA7 — Crystal/clock input / PORTA bit 7 |
| 핀 10 | OSC2/CLKO/RA6 — Crystal/clock output / PORTA bit 6 |
| 핀 11 | RC0/T1CKI — PORTC bit 0 / Timer1 clock input |
| 핀 12 | RC1 — PORTC bit 1 |
| 핀 13 | RC2/CCP1 — PORTC bit 2 / Capture-Compare-PWM 1 |
| 핀 14 | RC3 — PORTC bit 3 |
| 핀 15 | RC4 — PORTC bit 4 |
| 핀 16 | RC5 — PORTC bit 5 |
| 핀 17 | RC6/TX/CK — PORTC bit 6 / EUSART TX / clock |
| 핀 18 | RC7/RX/DT — PORTC bit 7 / EUSART RX / data |
| 핀 19 | VSS — Ground reference |
| 핀 20 | VDD — Positive supply (2.0V-5.5V for LF) |
| 핀 21 | RB0/INT0 — PORTB bit 0 / external interrupt 0 |
| 핀 22 | RB1/INT1 — PORTB bit 1 / external interrupt 1 |
| 핀 23 | RB2 — PORTB bit 2 |
| 핀 24 | RB3 — PORTB bit 3 |
| 핀 25 | RB4 — PORTB bit 4 |
| 핀 26 | RB5 — PORTB bit 5 |
| 핀 27 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 핀 28 | RB7/PGD — PORTB bit 7 / ICSP data |
일반적인 애플리케이션
PIC18LF2680-I/SO 적합 용도: 6 애플리케이션s: Automotive Body ECAN Nodes, Industrial Sensor Bus Nodes, HVAC and Building Automation Controllers, Battery Management CAN Nodes, CAN-Based Distributed Motor Control, Portable Medical Diagnostic Devices.
Automotive Body ECAN Nodes
The PIC18LF2680-I/SO's integrated ECAN 2.0B controller with acceptance filters makes it ideal for body-electronics ECAN nodes that exchange messages with door modules, lighting controllers, and instrument clusters. The 28-SOIC package's 300-mil body and wide pitch ease hand-soldering during prototype bring-up, while production runs use standard SMT reflow. With 64KB Flash and 3328 bytes RAM, the part can run a CANopen or J1939 lightweight stack plus diagnostics; bus termination uses 120 ohm at each end and a transceiver such as MCP2551. Compared with older PIC18F458 parts, the LF suffix allows direct 3.3V rail operation without a regulator.
추천
Industrial Sensor Bus Nodes
In factory-automation backplanes using CAN as the sensor backbone, the PIC18LF2680-I/SO provides sufficient MIPS (10 MIPS peak at 40 MHz) and Flash (64KB) to implement sensor linearization, calibration, and ECAN message packing. The LF voltage range (2.0V-5.5V) supports both legacy 24V-derived 5V rails and modern 3.3V I/O domains. Integrated 10-bit ADC and two analog comparators handle raw analog sensor signals; enhanced USART bridges to RS-485 or RS-232 when needed. The 28-SOIC's wide pitch improves manufacturability in mixed-technology panels with both SMD and through-hole sensors.
추천
HVAC and Building Automation Controllers
Building-automation nodes need to actuate dampers, fans, and valves while talking to a central ECAN or CANopen master - a workload well-suited to the PIC18LF2680-I/SO's 64KB Flash and 40 MHz CPU. The 10-bit ADC reads thermistor/resistive temperature sensors, while PWM timers drive triac-trigger circuits for heater control. The "I" temperature grade (-40C to +85C) covers unconditioned plant-room environments, and the LF's low-voltage tolerance accommodates remote battery-backed operation. MSSP peripherals drive I2C-based temperature/humidity sensor front-ends such as the MCP9808 family.
추천
Battery Management CAN Nodes
Portable medical, e-mobility, and robotics systems use ECAN to broadcast per-cell battery telemetry. The PIC18LF2680-I/SO is a strong fit because the LF 2.0V minimum allows direct 2S Li-Ion (7.4V via LDO to 3.3V) and 1S Li-Ion (3.7V) operation; the 28-SOIC package survives conformal coating and potting used in battery packs. With 3328 bytes RAM and 64KB Flash, the part can run coulomb counting plus ECAN message formatting without external memory. Designers pair the MCU with a CAN transceiver and an ADC front-end such as the MCP3421 for cell-voltage monitoring.
추천
CAN-Based Distributed Motor Control
Small distributed motor drives (fans, pumps, conveyor rollers) use PIC18LF2680-I/SO as the per-node controller, taking torque/speed commands from a CAN master and driving a gate-driver or H-bridge via PWM. The 40 MHz CPU handles Field-Oriented Control for low-pole-count BLDC motors and the ECAN peripheral keeps bus latency low. The 28-SOIC package dissipates up to ~1W comfortably when the JLDST020 reflow profile is followed, with copper-pour heatsinking. Programmer-signal protocols such as CANopen DS-301/DS-402 are easily hosted in 64KB Flash.
추천
Portable Medical Diagnostic Devices
Portable medical instruments (handheld ultrasound probes, pulse oximeters, point-of-care analyzers) demand a low-voltage, low-power 8-bit MCU with reliable communication - a profile matching the PIC18LF2680-I/SO. The LF 2.0V minimum extends runtime on partially-depleted Li-Ion packs, while ECAN links the device to a CAN-connected bedside monitor or charging cradle. The 10-bit ADC handles sensor front-ends and the MSSP drives SPI OLED displays. Industrial temperature grade plus the 28-SOIC's rework-friendly 300-mil body simplify service and field upgrades through ICSP.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18LF2680-I/SO — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F2680-I/SO | PIC18F2680-E/SO | PIC18LF2680T-I/SO |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SOIC (300 mil) | 28-SOIC (300 mil) | 28-SOIC (300 mil) | 28-SOIC (300 mil) |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB |
| RAM | 3328 bytes | 3328 bytes | 3328 bytes | 3328 bytes |
| Maximum Clock | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Operating Voltage | 2.0V-5.5V (LF) | 4.2V-5.5V (F) | 4.2V-5.5V (F) | 2.0V-5.5V (LF) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +85C |
| ECAN Controller | Yes | Yes | Yes | Yes |
| Lifecycle Status | Active | Active | Active | Active |
주요 차별점
- Wide low-voltage operating range 2.0V-5.5V (vs PIC18F2680-I/SO)
- Industrial -40C to +85C temperature range as standard (vs PIC18F2680-E/SO (extended))
- Pin-to-pin compatible with the broader PIC18F26xx family (vs PIC18F2610-I/SO (48KB Flash))
설계 노트
The LF suffix denotes low-voltage operation down to 2.0V VDD, but maximum CPU frequency must be derated below ~3V per the datasheet frequency-vs-voltage curves. At 40 MHz, VDD must be >= 4.2V; at 4 MHz the part can run on the full 2.0V-5.5V range. Add a bulk 10uF ceramic + 100nF decoupling pair close to VDD (pin 20) and a second 100nF near VSS (pin 19) to handle switching transients during ECAN transmission. nanoWatt technology modes (Sleep, Idle, Run) reduce Iq below 1uA for battery-powered designs.
Never drive the CAN bus pins directly - the PIC18LF2680-I/SO outputs only CANTX and CANRX logic levels. An external CAN transceiver such as MCP2551 (5V) or MCP2561 (3.3V) is mandatory to meet ISO 11898 bus levels and to provide bus-fault protection. Also note that the LF variant must NOT be operated below 2.0V even in Sleep mode without re-asserting Brown-Out Reset thresholds; configure BOR in the CONFIG words to guarantee clean reset behavior at low VDD.
The 28-SOIC (300-mil) footprint is wider than the 8-pin SOIC and demands a land pattern per JEDEC MS-013 with 1.27mm pitch. Place the decoupling capacitor within 2mm of the VDD pin, route the ICSP/ICD signals (RB6/PGC, RB7/PGD, MCLR/VPP) to a 5-pin header compatible with MPLAB ICD 4/5, and place a 4-pin CAN header near the CANTX/CANRX GPIO for transceiver breakout. Keep the crystal traces short and guard-ring the oscillator area to avoid noise injection on ECAN timing.
규정 준수 정보
RoHS and REACH compliance per Microchip product page. AEC-Q100 qualification is NOT claimed for the standard grade; for under-hood automotive ECAN nodes requiring AEC-Q100, designers must use automotive-grade PIC18 variants explicitly marked Q1 in the part number.
