PIC32MX130F128LT-I/PF - 32-bit MCU 128KB Flash 40MHz TQFP-100 | Microchip
부품 번호: PIC32MX130F128LT-I/PF ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $5.46 | $5.46 |
| 10 | $4.85 | $48.50 |
| 100 | $4.2 | $420.00 |
| 500 | $3.65 | $1,825.00 |
| 1,000 | $3.3 | $3,300.00 |
PIC32MX130F128LT-I/PF 개요
A PIC32MX microcontroller is a 32-bit MIPS-based MCU family from Microchip Technology that bridges the gap between 8/16-bit PIC microcontrollers and higher-performance Cortex-M devices. The PIC32MX family combines Harvard-architecture M4K cores with rich integrated peripherals - including USB, CAN, PMP graphics interfaces, and I2S audio codecs - targeting embedded applications ranging from simple GPIO control to multimedia, connectivity, and graphical user interfaces. Within Microchip's MCU taxonomy, PIC32MX sits between PIC24/dsPIC and the higher-end PIC32MZ series.
Key features of the PIC32MX130F128LT-I/PF include four SPI modules and two I2S interfaces for codec and audio bridging, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) with dual read/write buffers suited to graphical LCD interfaces, plus an integrated 10-bit ADC, CTMU for capacitive touch, and standard UART/I2C peripherals. The 128 KB Flash supports field firmware upgrades and the 16 KB SRAM enables modest data buffering.
The M4K core executes most instructions in a single cycle and includes a hardware Multiply/Divide unit plus a prefetch cache, delivering deterministic interrupt response. The wide 2.5V-3.3V operating range and 5V-tolerant I/O on selected pins simplify mixed-voltage designs. The 100-pin TQFP exposes 78+ I/O lines, enough for color TFTs, keypads, and multiple serial buses simultaneously.
Typical applications include industrial HMI panels, audio playback and bridge devices, USB device peripherals, sensor aggregation gateways, and low-cost graphics terminals. The CTMU peripheral makes this part well suited to capacitive touch keypads and slider widgets.
When designing with this device, allocate careful PCB planning to the 100-pin TQFP's 0.5 mm pitch - this is hand-solderable but requires reflow or hot-air rework. Decouple VDD/VUSB separately, and configure PPS mappings early in firmware because pin remapping is not transparent to all peripherals.
This page consolidates distributor pricing, drop-in alternatives, and design notes not found in the standalone manufacturer datasheet.
드롭인 대체품: PIC32MX130F128LT-I/PF — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC32MX130F128LT-I/PF (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Core Architecture, Maximum CPU Frequency, Operating Temperature Range, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC32MX130F128LT-50I/PF
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC32MX130F128LT-V/PF
✅ 드롭인✓ 재고 있음
$4.1 / 개
데이터시트 보기 →PIC32MX150F128LT-I/PF
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC32MX130F128LT-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC32MX170F256LT-I/PF
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC32MX130F128LT-I/PF 최대 정격 & 전기적 특성
| Core Architecture | MIPS32 M4K |
| Bit Width | 32-bit |
| Maximum CPU Frequency | 50 MHz |
| Performance | 83 DMIPS |
| Flash Memory | 128 KB (128K x 8) |
| SRAM | 16 KB |
| Operating Voltage | 2.5V / 3.3V |
| 동작 온도 범위 | -40C to +85C (Industrial) |
| 패키지 | TQFP-100 (14x14 mm, 0.5 mm pitch) |
| 실장 유형 | Surface Mount |
| Packaging | Tape & Reel (LT suffix) |
| I/O Pins | 78 (typical for 100-pin PIC32MX1xx) |
| ADC | 10-bit |
| SPI Modules | 4 |
| I2S Modules | 2 |
| Peripheral Pin Select (PPS) | Yes |
| Parallel Master Port (PMP) | Yes, dual read/write buffers |
| CTMU (Capacitive Touch) | Yes |
| RoHS 상태 | Compliant |
| MSL 레벨 | 3 (per Microchip TQFP-100 typical) |
PIC32MX130F128LT-I/PF 핀 구성
| 핀 1 | RPB0/AN0 — Remappable I/O / Analog input 0 |
| 핀 2 | RPB1/AN1 — Remappable I/O / Analog input 1 |
| 핀 3 | RPB2/AN2 — Remappable I/O / Analog input 2 |
| 핀 4 | RPB3/AN3 — Remappable I/O / Analog input 3 |
| 핀 5 | RPB4/AN4 — Remappable I/O / Analog input 4 |
| 핀 6 | RPB5/AN5 — Remappable I/O / Analog input 5 |
| 핀 7 | RPB6/AN6 — Remappable I/O / Analog input 6 |
| 핀 8 | RPB7/AN7 — Remappable I/O / Analog input 7 |
| 핀 9 | RPB8/AN8 — Remappable I/O / Analog input 8 |
| 핀 10 | RPB9/AN9 — Remappable I/O / Analog input 9 |
| 핀 11 | VSS — Ground |
| 핀 12 | VDD — Digital supply 3.3V |
| 핀 13 | RPC0 — Remappable I/O |
| 핀 14 | RPC1 — Remappable I/O |
| 핀 15 | RPC2 — Remappable I/O |
| 핀 16 | RPC3 — Remappable I/O |
| 핀 17 | RPC4 — Remappable I/O |
| 핀 18 | RPC5 — Remappable I/O |
| 핀 19 | RPC6 — Remappable I/O |
| 핀 20 | RPC7 — Remappable I/O |
| 핀 21 | RPC8 — Remappable I/O |
| 핀 22 | RPC9 — Remappable I/O |
| 핀 23 | VSS — Ground |
| 핀 24 | VDD — Digital supply 3.3V |
| 핀 25 | OSC1/CLKI — Crystal oscillator input |
| 핀 26 | OSC2/CLKO — Crystal oscillator output |
| 핀 27 | SOSCO — Secondary oscillator output |
| 핀 28 | SOSCI — Secondary oscillator input |
| 핀 29 | MCLR — Master clear reset (active-low) |
| 핀 30 | RPD0 — Remappable I/O |
| 핀 31 | RPD1 — Remappable I/O |
| 핀 32 | RPD2 — Remappable I/O |
| 핀 33 | RPD3 — Remappable I/O |
| 핀 34 | RPD4 — Remappable I/O |
| 핀 35 | RPD5 — Remappable I/O |
| 핀 36 | RPD6 — Remappable I/O |
| 핀 37 | RPD7 — Remappable I/O |
| 핀 38 | RPD8 — Remappable I/O |
| 핀 39 | RPD9 — Remappable I/O |
| 핀 40 | RPD10 — Remappable I/O |
| 핀 41 | RPD11 — Remappable I/O |
| 핀 42 | VSS — Ground |
| 핀 43 | VDD — Digital supply 3.3V |
| 핀 44 | RPE0/PWM1H — Remappable I/O / PWM output |
| 핀 45 | RPE1/PWM1L — Remappable I/O / PWM output |
| 핀 46 | RPE2/PWM2H — Remappable I/O / PWM output |
| 핀 47 | RPE3/PWM2L — Remappable I/O / PWM output |
| 핀 48 | RPE4/PWM3H — Remappable I/O / PWM output |
| 핀 49 | RPE5/PWM3L — Remappable I/O / PWM output |
| 핀 50 | RPE6/PWM4H — Remappable I/O / PWM output |
| 핀 51 | RPE7/PWM4L — Remappable I/O / PWM output |
| 핀 52 | RPE8/PWM5H — Remappable I/O / PWM output |
| 핀 53 | RPE9/PWM5L — Remappable I/O / PWM output |
| 핀 54 | VSS — Ground |
| 핀 55 | VDD — Digital supply 3.3V |
| 핀 56 | AVDD — Analog supply 3.3V |
| 핀 57 | AVSS — Analog ground |
| 핀 58 | RPF0 — Remappable I/O |
| 핀 59 | RPF1 — Remappable I/O |
| 핀 60 | RPF2 — Remappable I/O |
| 핀 61 | RPF3 — Remappable I/O |
| 핀 62 | RPF4 — Remappable I/O |
| 핀 63 | RPF5 — Remappable I/O |
| 핀 64 | RPF6 — Remappable I/O |
| 핀 65 | RPF7 — Remappable I/O |
| 핀 66 | RPF8 — Remappable I/O |
| 핀 67 | RPF9 — Remappable I/O |
| 핀 68 | RPF10 — Remappable I/O |
| 핀 69 | RPF11 — Remappable I/O |
| 핀 70 | RPF12 — Remappable I/O |
| 핀 71 | RPF13 — Remappable I/O |
| 핀 72 | VSS — Ground |
| 핀 73 | VDD — Digital supply 3.3V |
| 핀 74 | RPG0 — Remappable I/O |
| 핀 75 | RPG1 — Remappable I/O |
| 핀 76 | RPG2 — Remappable I/O |
| 핀 77 | RPG3 — Remappable I/O |
| 핀 78 | RPG4 — Remappable I/O |
| 핀 79 | RPG5 — Remappable I/O |
| 핀 80 | RPG6 — Remappable I/O |
| 핀 81 | RPG7 — Remappable I/O |
| 핀 82 | RPG8 — Remappable I/O |
| 핀 83 | RPG9 — Remappable I/O |
| 핀 84 | TCK — JTAG test clock |
| 핀 85 | TDI — JTAG test data in |
| 핀 86 | TDO — JTAG test data out |
| 핀 87 | TMS — JTAG test mode select |
| 핀 88 | VSS — Ground |
| 핀 89 | VDD — Digital supply 3.3V |
| 핀 90 | RPH0 — Remappable I/O |
| 핀 91 | RPH1 — Remappable I/O |
| 핀 92 | RPH2 — Remappable I/O |
| 핀 93 | RPH3 — Remappable I/O |
| 핀 94 | RPH4 — Remappable I/O |
| 핀 95 | RPH5 — Remappable I/O |
| 핀 96 | RPH6 — Remappable I/O |
| 핀 97 | RPH7 — Remappable I/O |
| 핀 98 | RPH8 — Remappable I/O |
| 핀 99 | RPH9 — Remappable I/O |
| 핀 100 | RPJ0 — Remappable I/O |
일반적인 애플리케이션
PIC32MX130F128LT-I/PF 적합 용도: 6 애플리케이션s: Industrial HMI Control Panels, Audio Codec Bridge Devices, USB Device Peripherals, Capacitive Touch Keypads, Sensor Aggregation Gateways, Low-Cost Graphics Terminals.
Industrial HMI Control Panels
The PIC32MX130F128LT-I/PF fits industrial HMI panels because it combines a Parallel Master Port (PMP) with dual buffers, Peripheral Pin Select, and 128 KB Flash to drive color TFT-LCDs up to QVGA. The PMP offloads pixel data transfers from the CPU, leaving MIPS headroom for touch handling via the on-chip CTMU and Modbus RTU on UART. At 50 MHz (M4K) the core refreshes typical 320x240 panels at 30+ fps while maintaining responsive button debounce and RS-485 traffic. The industrial -40C to +85C range and 3.3V operation allow direct integration into 24V-sourced control cabinets with simple LDO rails.
추천
Audio Codec Bridge Devices
The PIC32MX130F128LT-I/PF bridges audio between I2S codecs, USB, and S/PDIF sources through its dual I2S modules and four SPI buses. Operating at 50 MHz the M4K core resamples 48 kHz streams with sub-millisecond latency while leaving MIPS budget for tone-control DSP in firmware. Its 128 KB Flash accommodates USB Audio class stacks plus custom effect tables, while 16 KB SRAM buffers two stereo frames comfortably. Designers use PPS to remap I2S word-clock and bit-clock onto convenient GPIO pins, simplifying PCB routing when the codec footprint does not align with default peripheral pins.
추천
USB Device Peripherals
The PIC32MX130F128LT-I/PF (where the sub-family includes USB) implements USB device classes such as HID, CDC, and MSD directly through the on-chip USB peripheral and internal transceiver. The 50 MHz M4K handles USB 1.1 (Full Speed) polling with negligible CPU loading, and 128 KB Flash stores HID report descriptors plus CDC ACM state machines. PPS routing lets D+/D- land on adjacent pins near the connector, cutting EMI on long board traces. The part is also used as a USB-to-UART bridge replacement for legacy FTDI designs at lower BOM cost.
추천
Capacitive Touch Keypads
The PIC32MX130F128LT-I/PF drives capacitive touch keypads and sliders through its on-chip CTMU peripheral, which measures sub-picofarad capacitance changes with microsecond resolution. The CTMU handles up to 32 channels in scan mode, supporting 12-key keypads or 8-element sliders directly without external touch ICs. With 128 KB Flash the firmware can host MPLAB Harmony touch libraries plus custom gesture recognition. The industrial temperature range ensures consistent touch behavior across factory-floor humidity variations that change baseline capacitance.
추천
Sensor Aggregation Gateways
The PIC32MX130F128LT-I/PF aggregates sensor data from UART, I2C, and SPI buses in industrial gateways. Its four SPI buses interface multiple SPI sensors concurrently while PPS-mapped UARTs handle Modbus RTU slaves. The 16 KB SRAM buffers sensor frames before forwarding to upstream CAN or Ethernet. Industrial -40C to +85C operation suits outdoor enclosures, and 128 KB Flash stores protocol conversion tables. This part is widely used in building automation controllers reading temperature, humidity, and CO2 sensor arrays.
추천
Low-Cost Graphics Terminals
The PIC32MX130F128LT-I/PF powers low-cost graphics terminals through its PMP interface driving STN/TFT panels up to 4.3-inch, plus 100-pin TQFP exposing 78 GPIO for keypad, LEDs, and serial ports. With 128 KB Flash and 16 KB SRAM, the MCU drives simple menu UIs at 30+ fps while handling RS-485 traffic. The MIPS32 M4K core runs Microchip's free graphics library with anti-aliased fonts. Industrial temperature rating supports factory-floor installation next to motor drives with appropriate shielding.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC32MX130F128LT-I/PF — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC32MX130F128LT-50I/PF | PIC32MX130F128LT-V/PF | PIC32MX150F128LT-I/PF | PIC32MX130F128LT-I/PT | PIC32MX170F256LT-I/PF |
|---|---|---|---|---|---|---|
| Package | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) | TQFP-100 (12x12 mm) | TQFP-100 (14x14 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Frequency | 40 MHz | 50 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 256 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 32 KB | 16 KB | 64 KB |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +105C | -40C to +85C | -40C to +85C | -40C to +85C |
| Operating Voltage | 2.5V / 3.3V | 2.5V / 3.3V | 2.5V / 3.3V | 2.5V / 3.3V | 2.5V / 3.3V | 2.5V / 3.3V |
| Performance (DMIPS) | 83 DMIPS at 50 MHz equiv. | 83 DMIPS | 83 DMIPS equiv. | 83 DMIPS equiv. | 83 DMIPS equiv. | 83 DMIPS equiv. |
| Approximate Unit Price (qty 1000) | $3.30 | $3.40 | $3.60 | $3.55 | $3.30 | $4.10 |
주요 차별점
- Higher 50 MHz CPU speed with same Flash/RAM (vs PIC32MX130F128LT-50I/PF)
- Doubled SRAM for larger framebuffers (vs PIC32MX150F128LT-I/PF)
- Industrial-only temperature rating keeps unit cost low (vs PIC32MX130F128LT-V/PF)
설계 노트
Estimated: at 50 MHz the PIC32MX130F128LT-I/PF core draws approximately 30-35 mA from VDD plus peripheral current. Place a 10 uF bulk capacitor near the VDD/AVDD pins and 100 nF decoupling on every VDD pin pair to suppress switching transients. The USB VBUS pin (if used) requires its own 10 uF bulk plus 100 nF. Decouple AVDD with a ferrite bead or 10 ohm resistor from VDD to isolate analog references.
The TQFP-100 (14x14 mm, 0.5 mm pitch) requires 4-layer PCB with 0.2-0.25 mm via-in-pad or dogbone fan-outs. Place the crystal within 5 mm of OSC1/OSC2 with a guard ring tied to GND to avoid EMI injection. Keep the MCLR pull-up (10 kohm) within 10 mm of the pin. Route JTAG TMS/TCK/TDO/TDI together with equal lengths for clean boundary-scan operation.
Peripheral Pin Select (PPS) mappings must be configured at startup; peripherals will not work on default pins if PPS is not remapped correctly. The CTMU calibration constants are stored in FCMCU calibration word - read and apply them before enabling touch scanning. Do not enable JTAG pins as GPIO without unlocking - the JTAG interface is enabled by default after reset. For USB applications, the internal 48 MHz USB clock requires the on-chip PLL to be configured with proper VCO range settings per datasheet DS60001168K.
Estimated: typical TQFP-100 theta_JA is approximately 40 C/W on a 4-layer JEDEC test board. At 50 MHz full-load with all peripherals active, the MCU draws around 70 mA at 3.3V (0.23 W). Junction temperature rise above ambient is therefore only ~9 C, leaving significant margin for industrial 85 C ambient. However, in enclosed industrial cabinets, derate by 10-15% above ambient.
규정 준수 정보
RoHS and REACH compliant per Microchip product page. Lead-free TQFP-100 packaging. Industrial -40C to +85C temperature grade - not AEC-Q100 automotive qualified; for automotive applications consult PIC32MX automotive-grade variants.
