S9S08EL32F1MTL - 8-bit S08 MCU, 32KB Flash, 40MHz | NXP Semiconductors
부품 번호: S9S08EL32F1MTL ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.92 | $4.92 |
| 10 | $4.43 | $44.30 |
| 100 | $3.94 | $394.00 |
| 500 | $3.54 | $1,770.00 |
| 1,000 | $3.15 | $3,150.00 |
S9S08EL32F1MTL 개요
An 8-bit MCU (microcontroller unit) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data RAM, and a set of on-chip peripherals. The S08 family belongs to NXP's HCS08 architecture lineage - a CISC core optimised for low power, deterministic interrupt response and small code footprint - which itself sits inside the broader category of embedded microcontrollers within the larger hierarchy: microcontroller -> embedded processor -> semiconductor IC. Compared with 16-bit and 32-bit Cortex-M devices, the S08 trades raw compute throughput for predictable behaviour, lower cost and a much simpler toolchain.
Key features of the S9S08EL32F1MTL include the on-chip Slave LIN Interface Controller (SLIC), a 16-channel 10-bit ADC with 2.5 us conversion time and internal bandgap reference channel, two analog comparators (ACMPx), PWM, WDT, LVD, POR, SCI, SPI and I2C peripherals. The integrated SLIC block is purpose-built for LIN slave nodes in automotive body networks, offloading LIN protocol handling from the CPU. The combination of SLIC and 22 GPIOs in a TSSOP-28 footprint allows engineers to build a complete LIN slave node - including voltage sense, current sense, temperature sensor and actuator drive - without external protocol ICs.
Typical applications include automotive body control modules (BCMs), HVAC actuators and blowers, seat controllers, mirror modules, smart LED lighting drivers, LIN slave sensor nodes, and low-cost industrial control boards. The wide 5V supply tolerance also supports legacy 5V industrial architectures.
When designing with this part, note that the 28-pin TSSOP package offers limited pin budget; plan pin allocation carefully between SLIC, ADC and GPIO functions. Always include a 0.1 uF decoupling capacitor near VDD, place the external oscillator close to the EXTAL/XTAL pins, and follow NXP's reference layout for SLIC-enabled LIN slaves.
This page synthesises distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: S9S08EL32F1MTL — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: S9S08EL32F1MTL (동일 폼 팩터 및 풋프린트) — 차이점: Mounting Type, Operating Temperature, ADC, Core Architecture, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
S9S08SL8F1MTL
✅ 드롭인✓ 재고 있음
$1.72 / 개
데이터시트 보기 →S9S08EL32F1MTL
✅ 드롭인✓ 재고 있음
$3.15 / 개
데이터시트 보기 →S9S08SG16E1CTL
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F25K22-I/SP
✅ 드롭인✓ 재고 있음
$2.45 / 개
데이터시트 보기 →PIC18F26K22-I/SP
✅ 드롭인✓ 재고 있음
$2.55 / 개
데이터시트 보기 →S9S08EL32F1MTL 최대 정격 & 전기적 특성
| Core Processor | HCS08 (S08) |
| Core Size | 8-bit |
| Core Architecture | CISC |
| 최대 클록 주파수 | 40 MHz |
| Program Memory Size | 32 KB (32K x 8) Flash |
| RAM Size | 1 KB (1K x 8) |
| EEPROM Size | 512 bytes (512 x 8) |
| Number of I/O Pins | 22 |
| 패키지 | 28-TSSOP (4.40 mm width) |
| 공급 전압 | 3.3 V / 5 V |
| 동작 온도 | -40C to +125C |
| ADC | 16-channel, 10-bit, 2.5 us conversion |
| Analog Comparators | 2 x ACMP |
| On-chip LIN Controller | Slave LIN Interface Controller (SLIC) |
| Connectivity | I2C, LINbus, SCI, SPI |
| Peripherals | LVD, POR, PWM, WDT |
| Oscillator | External |
| Automotive Qualification | AEC-Q100 |
| 실장 유형 | Surface Mount |
| Packaging | Tube |
S9S08EL32F1MTL 핀 구성
| 핀 1 | PTC4 — Port C bit 4 / IRQ / BKGD (debug) |
| 핀 2 | PTC5 — Port C bit 5 / RESET |
| 핀 3 | PTC6 — Port C bit 6 |
| 핀 4 | VDD — Supply voltage (3.3 V or 5 V) |
| 핀 5 | VSS — Ground |
| 핀 6 | PTC7 — Port C bit 7 |
| 핀 7 | PTB0 — Port B bit 0 / ADC0 |
| 핀 8 | PTB1 — Port B bit 1 / ADC1 |
| 핀 9 | PTB2 — Port B bit 2 / ADC2 / ACMP+ input |
| 핀 10 | PTB3 — Port B bit 3 / ADC3 / ACMP- input |
| 핀 11 | PTB4 — Port B bit 4 / ADC4 |
| 핀 12 | PTB5 — Port B bit 5 / ADC5 |
| 핀 13 | PTB6 — Port B bit 6 / ADC6 |
| 핀 14 | PTB7 — Port B bit 7 / ADC7 |
| 핀 15 | PTA0 — Port A bit 0 / SCI Tx / SLIC TXD |
| 핀 16 | PTA1 — Port A bit 1 / SCI Rx / SLIC RXD |
| 핀 17 | PTA2 — Port A bit 2 / SDA / SLIC |
| 핀 18 | PTA3 — Port A bit 3 / SCL / SLIC |
| 핀 19 | PTA4 — Port A bit 4 / SPI MISO |
| 핀 20 | PTA5 — Port A bit 5 / SPI MOSI |
| 핀 21 | PTA6 — Port A bit 6 / SPI SCK |
| 핀 22 | PTA7 — Port A bit 7 / SPI SS |
| 핀 23 | PTG0 — Port G bit 0 / PWM channel |
| 핀 24 | PTG1 — Port G bit 1 / PWM channel |
| 핀 25 | EXTAL — External oscillator input |
| 핀 26 | XTAL — External oscillator output |
| 핀 27 | VDDA — Analog supply voltage |
| 핀 28 | VSSA — Analog ground |
일반적인 애플리케이션
S9S08EL32F1MTL 적합 용도: 6 애플리케이션s: Automotive Body Control Module (BCM), HVAC Actuator and Seat Control Modules, Automotive Mirror and Lighting Modules, LIN Slave Sensor Nodes, Low-Cost Industrial Control Boards, Smart Sensor and Actuator Modules.
Automotive Body Control Module (BCM)
The S9S08EL32F1MTL fits automotive BCMs because its 32 KB Flash accommodates BCM application code, while the integrated Slave LIN Interface Controller (SLIC) handles LIN 2.x slave protocol offload. The 22 GPIOs can drive LEDs, switches and relay drivers directly; the 16-channel 10-bit ADC reads analog body sensors such as ambient light and humidity. AEC-Q100 qualification with -40C to +125C and 5 V tolerance allow direct connection to the 12 V automotive battery rail.
추천
HVAC Actuator and Seat Control Modules
HVAC actuators and seat control modules require deterministic 8-bit control with multiple PWM outputs and analog feedback - a perfect fit for the S9S08EL32F1MTL. The device's PWM peripherals drive BLDC motors and DC actuators, while the two on-chip analog comparators (ACMPx) support over-current and position sensing. The 1 KB SRAM and 512-byte EEPROM store calibration data across -40C to +125C, and the SLIC block provides LIN slave communication to the vehicle network.
추천
Automotive Mirror and Lighting Modules
Mirror and lighting modules need LIN slave connectivity, PWM LED dimming and small footprint - all met by the S9S08EL32F1MTL in a compact 28-TSSOP package. The SLIC block provides LIN slave communication to the body controller; the PWM outputs drive LED current regulators and mirror motor drivers. AEC-Q100 qualification ensures reliability under thermal stress; the 22 GPIOs connect directly to mirror position sensors and turn-indicator LEDs without external expanders.
추천
LIN Slave Sensor Nodes
Distributed LIN sensor nodes (temperature, pressure, position) use the S9S08EL32F1MTL as a single-chip solution thanks to its integrated SLIC. The 16-channel 10-bit ADC with 2.5 us conversion time and internal bandgap reference handles multiple sensor inputs; the temperature sensor channel enables on-die thermal monitoring. Stop3 low-power mode keeps quiescent current low for always-on battery nodes; 5 V tolerance permits direct connection to vehicle bus power.
추천
Low-Cost Industrial Control Boards
For 5 V industrial control boards not requiring full automotive qualification, the S9S08EL32F1MTL offers 40 MHz S08 performance, 32 KB Flash and a rich peripheral set at low BOM cost. The I2C, SPI and SCI peripherals support sensor hubs and Modbus-style communication; the 22 GPIOs can interface to keypads, displays and relay outputs. Industrial designers appreciate the wide 3.3 V/5 V supply range and the mature, free CodeWarrior development toolchain from NXP.
추천
Smart Sensor and Actuator Modules
Smart sensor hubs and actuator modules benefit from the S9S08EL32F1MTL's combination of analog comparators, ADC, PWM and serial interfaces in a 28-TSSOP package. The two ACMPs support threshold detection for over-current, over-voltage or zero-cross events, while the PWM outputs drive proportional solenoids and heating elements. The 512-byte EEPROM stores calibration and unit-identity data non-volatilely across the -40C to +125C range.
추천
추천 제품 요약
엔지니어링 참조 데이터: S9S08EL32F1MTL — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | S9S08SL8F1MTL | S9S08SG16E1CTL | PIC18F25K22-I/SP | PIC18F26K22-I/SP |
|---|---|---|---|---|---|
| Package | 28-TSSOP | 28-TSSOP - same | 28-TSSOP - same | 28-TSSOP (SPDIP) - same footprint family | 28-TSSOP (SPDIP) - same footprint family |
| Brand | NXP Semiconductors | NXP Semiconductors - same brand | NXP Semiconductors - same brand | Microchip Technology - cross-brand | Microchip Technology - cross-brand |
| Core Architecture | HCS08 (S08) 8-bit CISC | HCS08 (S08) 8-bit CISC - same | HCS08 (S08) 8-bit CISC - same | PIC18 8-bit RISC - different | PIC18 8-bit RISC - different |
| Maximum Clock Frequency | 40 MHz | 40 MHz | 40 MHz | 64 MHz | 64 MHz |
| Program Memory (Flash) | 32 KB | 8 KB | 16 KB | 32 KB | 64 KB |
| RAM Size | 1 KB | 1 KB | 1 KB | 1.5 KB | 3.8 KB |
| EEPROM | 512 B | 512 B | 256 B | 256 B | 1 KB |
| On-chip LIN Controller | Yes (SLIC) | Yes (SLIC) | No (SCI bit-banged) | No (EUSART software LIN) | No (EUSART software LIN) |
| Automotive Qualification | AEC-Q100 (-40C to +125C) | AEC-Q100 - same | AEC-Q100 - same | AEC-Q100 (industrial grade -I) | AEC-Q100 (industrial grade -I) |
| Number of I/O Pins | 22 | 22 | 22 | 25 | 25 |
| ADC | 16-ch / 10-bit / 2.5 us | 16-ch / 10-bit | 16-ch / 10-bit | 19-ch / 10-bit | 19-ch / 10-bit |
주요 차별점
- Integrated Slave LIN Interface Controller (SLIC) offloads LIN protocol (vs S9S08SG16E1CTL)
- 32 KB Flash plus 512 B EEPROM on-chip (vs S9S08SL8F1MTL)
- AEC-Q100 automotive grade at 5 V in a TSSOP-28 footprint (vs PIC18F25K22-I/SP)
설계 노트
Decouple VDD/VSS and VDDA/VSSA pairs with separate 0.1 uF ceramic capacitors placed as close to the pins as possible (within 3 mm). For automotive 12 V battery applications, add a bulk 10 uF tantalum plus a series ferrite bead on VDD to suppress load-dump and reverse-battery transients. The on-chip LVD and POR circuits handle brown-out conditions, but external TVS protection (e.g. SMBJ) is recommended for AEC-Q100 conformance.
Route the EXTAL/XTAL traces symmetrically with short, equal lengths and guard them with a ground pour to minimise oscillator jitter. Keep ADC analog traces (PTB0-PTB7) away from PWM and switching signals to reduce coupling; place the analog ground (VSSA) star-connected to VSS at the regulator ground point. The SLIC LIN pins require a series 1 nF X7R cap plus an external ESD diode array rated to IEC 61000-4-2 for automotive bus protection.
Do not confuse the 28-TSSOP variant (S9S08EL32F1MTL) with the 32-LQFP package (S9S08EL32F1MLF) - they have different pin counts and PCBs are not interchangeable. When migrating from Freescale-era stock, note that part markings changed after the NXP acquisition but the silicon is identical. Ensure the BKGD/MS debug pin is accessible in production for firmware updates, or wire it to a test pad.
At 40 MHz with full peripheral activity, the S9S08EL32F1MTL consumes approximately 25-30 mA. The 28-TSSOP package has a thermal resistance of approximately 110 C/W theta-JA, so at 85C ambient the junction rises 3-5C - well within the 125C automotive limit. For sealed enclosures with no airflow, derate peripheral switching activity or move to the 32-LQFP variant which has lower theta-JA.
규정 준수 정보
AEC-Q100 qualified per NXP product page and DigiKey listing. RoHS compliant. Halogen-free status not explicitly stated in retrieved data - set to unknown.
