SN74HC241N - 8-Channel 3-State Buffer Driver | Texas Instruments
부품 번호: SN74HC241N ✓ 활성SN74HC241N 개요
An HC-series bus buffer is a digital logic device that strengthens signals passing between a driving source and a receiving load. Its role in the broader hierarchy is CMOS logic → bus interface IC → buffer or line driver. The SN74HC241N is intended to improve the performance and density of memory address drivers, clock drivers, and bus-oriented transmitters and receivers. Its 3-state outputs allow multiple devices to share a bus when the disabled outputs enter a high-impedance state.
Key features include eight non-inverting channels, two independently controlled four-bit output groups, 2 V to 6 V operation, and 3-state output capability. The split output-enable arrangement provides finer bus control than a single eight-bit enable, making it suitable for systems where two address groups or independent data paths require separate tri-state control. The device operates from the same 2 V to 6 V range commonly used by 74HC-compatible digital systems.
The SN74HC241N provides logic-level buffering without introducing inversion, so source data polarity remains unchanged at the outputs. Because each four-bit group has its own output-enable input, a system can place one group into the high-impedance state while the other continues driving. This arrangement is useful in bidirectional-bus interface arrangements, bidirectional transceivers, memory address multiplexing, and clock-distribution stages.
Typical applications include microprocessor and microcontroller address buses, memory address drivers, clock and control-signal distribution, bus isolation between functional blocks, and general-purpose tri-state data-bus routing. The through-hole PDIP package also suits legacy industrial control systems, educational instruments, prototypes, and maintenance replacements where a socketed 20-pin DIP footprint is preferred.
When designing around the SN74HC241N, treat the two output-enable groups independently and ensure that only one driver actively sources a shared net. Confirm every output state during normal operation and while the corresponding group is disabled. Decoupling requirements and operating limits should be taken from the manufacturer datasheet, and any replacement should be checked for identical enable polarity, channel arrangement, and pin mapping.
This page organizes the device function, package details, drop-in candidates, application guidance, and design cautions into one engineering reference. It also adds practical routing and bus-ownership advice that helps shorten design review and component-replacement work.
드롭인 대체품: SN74HC241N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
SN74HC241NE4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SN74HC241NE
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
SN74HC241N
✅ 드롭인가격 문의
데이터시트 보기 →SN74HC241N 최대 정격 & 전기적 특성
| Product Type | Octal non-inverting buffer and line driver |
| Number of Channels | 8 channels |
| 출력 구성 | 3-state output |
| Channel Organization | 2 groups of 4 bits |
| Supply Voltage Range | 2 V to 6 V |
| Output Enable Inputs | 2 independent output-enable inputs |
| Output Enable Polarity | 1OE active low; 2OE active high |
| Data Polarity | Non-inverting |
| 패키지 | 20-pin PDIP |
| 실장 유형 | Through-hole |
| Logic Family | 74HC CMOS logic |
SN74HC241N 핀 구성
| 핀 1 | 1A1 — Data input for channel 1 of group 1 |
| 핀 2 | 1Y1 — Non-inverting output for channel 1 of group 1 |
| 핀 3 | 2A1 — Data input for channel 1 of group 2 |
| 핀 4 | 2Y1 — Non-inverting output for channel 1 of group 2 |
| 핀 5 | GND — Ground connection |
| 핀 6 | 1OE — Active-low output enable for the first four-bit group |
| 핀 7 | 1A2 — Data input for channel 2 of group 1 |
| 핀 8 | 1Y2 — Non-inverting output for channel 2 of group 1 |
| 핀 9 | 2A3 — Data input for channel 3 of group 2 |
| 핀 10 | 2Y4 — Non-inverting output for channel 4 of group 2 |
| 핀 11 | 2OE — Active-high output enable for the second four-bit group |
| 핀 12 | 2Y3 — Non-inverting output for channel 3 of group 2 |
| 핀 13 | 2A4 — Data input for channel 4 of group 2 |
| 핀 14 | 2Y2 — Non-inverting output for channel 2 of group 2 |
| 핀 15 | 1Y4 — Non-inverting output for channel 4 of group 1 |
| 핀 16 | 1A4 — Data input for channel 4 of group 1 |
| 핀 17 | 1Y3 — Non-inverting output for channel 3 of group 1 |
| 핀 18 | 1A3 — Data input for channel 3 of group 1 |
| 핀 19 | VCC — Positive power supply connection |
| 핀 20 | GND — Ground connection |
일반적인 애플리케이션
SN74HC241N 적합 용도: 6 애플리케이션s: Memory Address Driver, Clock Signal Distribution, Tri-State Data Bus Interface, Microcontroller Interface Isolation, Bus-Oriented Receiver and Transmitter Stage, Legacy Industrial Control Upgrade.
Memory Address Driver
The SN74HC241N is suited to driving microprocessor or memory address lines because it provides eight non-inverting channels with 3-state outputs. Its two independent four-bit enable groups allow an address bus to be divided into separately controlled sections, which can simplify partial memory-bank isolation. Place the device close to the memory connectors or memory-array inputs so the buffered signals reach the load with minimal board-trace degradation. Verify propagation delay and output timing against the memory access window, and confirm that only one driver remains enabled on each shared address net.
추천
Clock Signal Distribution
The SN74HC241N can distribute a clock or control signal to multiple destinations while keeping unused outputs in the high-impedance state. Eight non-inverting channels support one-to-many clock fan-out, and the split enable architecture permits four outputs to operate independently from the other four. Keep clock traces short, provide a clean source clock, and avoid excessive capacitive loading on any single channel. Because the device is a CMOS line driver rather than a dedicated low-skew clock buffer, validate edge quality and duty-cycle margin in the target system.
추천
Tri-State Data Bus Interface
The SN74HC241N supports shared-bus designs because its outputs can be disabled into a high-impedance state. Two separately enabled four-bit groups are especially useful when two subsystems must connect and release the same collection of nets at different times. Establish a deterministic ownership rule so that no two enabled drivers contend for one line. Route the data group and its enable signals together, keep stub lengths short, and confirm that every output-enable pin is actively controlled rather than left floating.
추천
Microcontroller Interface Isolation
The SN74HC241N can isolate a microcontroller interface from a wider system bus while preserving non-inverted logic polarity. Enabling only the four channels associated with the local peripheral prevents unused section outputs from loading the shared bus. Route the enable inputs directly to the controlling logic and use pull resistors where a reset or power-up state requires a defined output condition. Validate that the disabled group presents the intended impedance and that the enabled group meets the load's input-voltage and capacitance requirements.
추천
Bus-Oriented Receiver and Transmitter Stage
The SN74HC241N is appropriate for intermediate bus-oriented receiver and transmitter stages where non-inverting buffering and output isolation are required. Its 2 V to 6 V operating range allows use in both low-voltage and 5 V HC-compatible environments, subject to the input and output thresholds of each system. Place the device between the logic source and the bus connector or backplane interface, then use controlled enable signals to prevent contention during module transitions. Review signal-integrity requirements for the board because no additional series termination is implied by the buffer function.
추천
Legacy Industrial Control Upgrade
The 20-pin PDIP package makes the SN74HC241N useful for maintenance and modernization of legacy industrial control boards that use socketed through-hole logic. The octal buffer function can replace older address-driver or bus-interface stages while retaining a familiar footprint and separate four-bit enable control. Before installation, compare the original device's pinout, enable polarity, supply voltage, and output timing with the manufacturer datasheet. Confirm that the replacement board does not expose unused inputs and that its supply rails meet the 2 V to 6 V operating requirement.
추천
추천 제품 요약
엔지니어링 참조 데이터: SN74HC241N — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | SN74HC241NE4 | SN74HC241NE | SN74HC241N |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Lattice Semiconductor |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Function | Octal non-inverting 3-state buffer/line driver | Octal non-inverting 3-state buffer/line driver | Octal non-inverting 3-state buffer/line driver | Octal non-inverting 3-state buffer/line driver |
| Channel Count | 8 channels | 8 channels | 8 channels | 8 channels |
| Channel Organization | Two 4-bit groups | Two 4-bit groups | Two 4-bit groups | Two 4-bit groups |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
| Output Enable Arrangement | Separate 1OE and 2OE controls | Separate 1OE and 2OE controls | Separate 1OE and 2OE controls | Separate 1OE and 2OE controls |
| Output Enable Polarity | 1OE active low; 2OE active high | 1OE active low; 2OE active high | 1OE active low; 2OE active high | 1OE active low; 2OE active high |
| Data Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
주요 차별점
- Independent enable control for each four-bit group (vs SN74HC241N)
- Mixed enable polarity supports direct group selection (vs SN74HC541N)
- Non-inverting buffered bus drive (vs SN74HC241NE4)
설계 노트
Do not treat the two output-enable inputs as having identical polarity. The SN74HC241N uses an active-low 1OE input and an active-high 2OE input, exactly as stated in the TI description. Driving both enables with the same straight logic level can disable one group and enable the other unintentionally. Verify each connection in the schematic and confirm that no enable input can float during reset.
Route each four-bit data group close to its associated outputs and keep the two enable traces away from high-current switching paths. Maintain a continuous ground path under the device and place the supply bypass capacitor near the VCC and GND pins. For longer board traces, review the capacitive-load requirements and timing budget in the manufacturer datasheet before adding series termination.
The SN74HC241N is designed to improve bus-driver performance, but a buffer cannot remove poor board-level signal integrity. Avoid stubs on address or clock nets, minimize capacitive loading, and keep clock outputs away from switching edges that create large crosstalk. If two independent blocks can drive the same bus, define strict ownership sequencing so their outputs are never enabled simultaneously.
규정 준수 정보
The device is a general-purpose 74HC CMOS logic buffer/line driver. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation or lot-specific material declarations.