Texas Instruments

SN74LS541N - 8-Bit 3-State Buffer | Texas Instruments

부품 번호: SN74LS541N ✓ 활성
4.75 V to 5.25 V Vdss 20-pin PDIP Package
MOQ: 1 |

SN74LS541N 개요

The Texas Instruments SN74LS541N is an 8-channel, non-inverting bipolar buffer and line driver with 3-state outputs, designed for a 4.75 V to 5.25 V supply and packaged in a 20-pin PDIP. It provides eight independently controlled output channels for buffering address, clock, control, and general-purpose bus signals. The active-low output-enable inputs place the outputs in a high-impedance state when the device is disabled, allowing multiple devices to share a bus.

An octal buffer and line driver is a digital logic IC positioned between a source device and a receiving bus. Its function belongs to the broader bus-interface and buffer-driver hierarchy, where it improves drive capability and provides controlled tri-state operation. The SN74LS541 is useful when a system must support bus-oriented transmission, memory addressing, clock distribution, or logic-level isolation without allowing undriven nodes to contend during inactive periods.

The primary features of the SN74LS541N include eight non-inverting channels, a 4.75 V to 5.25 V operating supply range, bipolar technology, and independently controlled 3-state outputs. Its two active-low output-enable inputs allow groups of four outputs to be disabled independently. This flexibility is valuable in multiplexed buses, bidirectional interface arrangements, and systems that require release of a shared data path during inactive intervals.

The SN74LS541 family differs from related LS540 and LS240-family arrangements through its physical pin organization, with inputs and outputs positioned on opposite sides of the package. That arrangement simplifies board routing when traces enter from one edge and leave through the other. The device is intended as a buffer rather than a level translator, so system designers must confirm that source and destination logic levels are compatible with the LS-family input and output thresholds.

Typical uses include memory address drivers, clock drivers, bus-oriented transmitters and receivers, control-signal isolation, and interfaces involving 5 V processors or programmable logic. Two enable inputs can manage four channels per bank, enabling partial bus participation. Because the outputs enter a high-impedance state only when the corresponding enable is pulled low, every enable input must be actively controlled and should not be left floating.

For PCB implementation, place the device close to the driven bus and maintain short, continuous output traces. Decoupling requirements and guaranteed electrical characteristics must be taken directly from the manufacturer datasheet. When substituting another 74LS-family device, verify the complete pin assignment, enable polarity, supply range, and output timing rather than relying only on the octal-buffer description.

This page organizes the SN74LS541N function, package, pin assignments, operating limits, commercial information, and drop-in comparison options into a design-focused reference. It also identifies practical bus-routing and enable-control considerations that are especially important when the device is used in shared 5 V digital systems.

드롭인 대체품: SN74LS541N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

SN54LS541N

✅ 드롭인
📦 20-pin PDIP (N)
Same 8-channel 3-state buffer function and 20-pin PDIP pinout, with a military-temperature grade instead of the commercial SN74LS541N grade; timing and temperature limits require verification.

📋 참조 대체품 (카탈로그에 없음)

SN74LS541N

✅ 드롭인
Texas Instruments
📦 20-pin PDIP (N)
8 channels · 8 bits per element · Non-inverting buffer and line driver · 3-state · 4.75 V to 5.25 V · Bipolar · 2 active-low output-enable inputs · 20-pin PDIP

가격 문의

데이터시트 보기 →

SN74LS541N

✅ 드롭인
Texas Instruments
📦 20-pin PDIP (N)
8 channels · 8 bits per element · Non-inverting buffer and line driver · 3-state · 4.75 V to 5.25 V · Bipolar · 2 active-low output-enable inputs · 20-pin PDIP

가격 문의

데이터시트 보기 →

DM74LS541N

✅ 드롭인
📦 20-pin PDIP (N)
Same 8-channel non-inverting 3-state buffer and 20-pin PDIP format, but the DM prefix identifies a different legacy ordering code; enable polarity, timing, and temperature limits must be confirmed.

📋 참조 대체품 (카탈로그에 없음)

HD74LS541P

✅ 드롭인
📦 20-pin PDIP (P)
Same 8-channel 3-state buffer concept in a 20-pin PDIP package, with a manufacturer-specific P ordering suffix and legacy sourcing status; compare pinout, timing, and temperature grade before use.

📋 참조 대체품 (카탈로그에 없음)

SN74LS541N 최대 정격 & 전기적 특성

Number of Channels 8 channels
Bits per Element 8 bits per element
Logic Type Non-inverting buffer and line driver
Output State 3-state
Supply Voltage Range 4.75 V to 5.25 V
Technology Bipolar
Output-enable Control 2 active-low output-enable inputs
패키지 20-pin PDIP
실장 유형 Through-hole
기능 Octal buffer and line driver
Input-to-Output Arrangement Inputs and outputs on opposite sides of the package
High-Impedance Output Capability 8 independently enabled outputs organized as two banks of 4

SN74LS541N 핀 구성

DIP-20 Package Pinout Diagram DIP-20 20-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 DIP-20
핀 1 1A — Data input for output 1
핀 2 2A — Data input for output 2
핀 3 3A — Data input for output 3
핀 4 4A — Data input for output 4
핀 5 GND — Ground
핀 6 1Y — Data output 1
핀 7 2Y — Data output 2
핀 8 3Y — Data output 3
핀 9 4Y — Data output 4
핀 10 3LE — Active-low output-enable input for outputs 1 through 4
핀 11 4LE — Active-low output-enable input for outputs 5 through 8
핀 12 GND — Ground
핀 13 5Y — Data output 5
핀 14 6Y — Data output 6
핀 15 7Y — Data output 7
핀 16 8Y — Data output 8
핀 17 8A — Data input for output 8
핀 18 7A — Data input for output 7
핀 19 6A — Data input for output 6
핀 20 5A — Data input for output 5

일반적인 애플리케이션

SN74LS541N 적합 용도: 6 애플리케이션s: Memory Address Buffering, Clock Signal Distribution, Shared Processor Bus Interface, Bidirectional Data-Path Isolation, Industrial Control Signal Distribution, Test and Measurement Fixture.

🖥️

Memory Address Buffering

The SN74LS541N fits memory-address routing because it provides eight non-inverting channels and allows each output bank to be released through the active-low output-enable inputs. In a 4.75 V to 5.25 V memory system, the device can buffer processor or controller address lines before they reach memory and peripheral devices. The opposing input and output sides of the 20-pin PDIP simplify point-to-point board routing. Its 3-state capability is particularly useful when address buses are multiplexed or several destinations share a common bus. Confirm propagation delay and output-current limits against the actual memory timing before layout release.

⚡

Clock Signal Distribution

The SN74LS541N can distribute a 5 V clock across up to eight non-inverting channels, reducing the loading burden on a clock-generating logic device. Its eight buffers are grouped under two active-low output-enable inputs, so a design can independently keep four channels active while placing another four in the high-impedance state. This arrangement suits peripheral clock trees, control-signal distribution, and test systems that need to isolate inactive clock branches. Because the SN74LS541N is not a frequency translator, the source clock frequency, load capacitance, and timing budget must satisfy the manufacturer’s operating limits.

🖥️

Shared Processor Bus Interface

The SN74LS541N is appropriate for a 5 V processor bus when the system requires eight buffered, non-inverting lines with controlled bus release. The two active-low enables can disconnect four outputs at a time, preventing inactive outputs from fighting a shared node and helping maintain predictable bus behavior. Its 20-pin PDIP package also suits through-hole legacy and industrial control assemblies. The device does not change logic voltage levels, so both the driver and receiver must use compatible thresholds. Engineers should verify timing, fanout, bus loading, and contention behavior in the completed system.

🌐

Bidirectional Data-Path Isolation

The SN74LS541N can support controlled directional paths by combining separate input and output channels with independent high-impedance control. In a bus-oriented transmitter or receiver arrangement, one output bank may be enabled while the opposite bank is disabled, limiting contention during direction changes. The 4.75 V to 5.25 V operating range suits conventional TTL-compatible 5 V systems, while the eight channels provide practical routing granularity. The circuit still needs external direction-control logic because the device does not autonomously determine bus direction. Confirm signal direction, setup and hold timing, and output loading against the manufacturer datasheet.

🏭

Industrial Control Signal Distribution

The SN74LS541N can distribute interlock, enable, and machine-control signals within a 5 V industrial control assembly. Eight non-inverting channels reduce the number of dedicated driver stages, while the two output-enable groups allow subsets of the control network to be disabled during transitions or maintenance states. The 20-pin PDIP package is well suited to through-hole control boards with long product lives. Industrial environmental requirements still need careful review: use the manufacturer temperature-range limits, maintain adequate supply bypassing, and keep switching-node or high-current power wiring away from sensitive logic traces.

🧩

Test and Measurement Fixture

The SN74LS541N is useful in a test fixture that drives eight instrumentation-control or address lines while selectively releasing unused outputs. Its 3-state outputs help prevent inactive fixture channels from loading the device under test, and its non-inverting organization simplifies control-logic integration. The two active-low enable groups make it possible to isolate four channels independently from the other four. For accurate measurements, account for the device’s propagation delay, output rise and fall behavior, and loading in the test setup. The 4.75 V to 5.25 V supply range requires a stable 5 V source with normal logic-level tolerances.

추천 제품 요약

SN74LS373N Octal latch commonly paired with address and data-control logic 사용처: Memory Address Buffering, Test and Measurement Fixture SN74LS240N Texas Instruments 사용처: Memory Address Buffering, Clock Signal Distribution, Bidirectional Data-Path Isolation, Test and Measurement Fixture SN74LS125N Quad 3-state buffer for branch isolation 사용처: Clock Signal Distribution, Industrial Control Signal Distribution MC74F243M onsemi 사용처: Shared Processor Bus Interface MC74F538N onsemi 사용처: Shared Processor Bus Interface, Industrial Control Signal Distribution SN74LS245N Octal bidirectional bus transceiver with direction control 사용처: Bidirectional Data-Path Isolation
What are the key specifications of SN74LS541N that engineers should know?
The SN74LS541N is an 8-channel, non-inverting 3-state buffer and line driver operating from 4.75 V to 5.25 V in a 20-pin PDIP package. According to the Texas Instruments manufacturer datasheet, it contains eight 1-bit buffers with common bipolar technology and two active-low output-enable inputs that control two groups of four outputs. These characteristics make it suitable for address, clock, control, and shared-bus buffering when the connected logic uses compatible 5 V levels.
Where can I download the SN74LS541N datasheet PDF?
The official SN74LS541N datasheet PDF is available from the Texas Instruments literature server through the product's manufacturer page. The document describes the octal buffer and line driver, its 4.75 V to 5.25 V supply range, 3-state outputs, package information, and electrical characteristics. Use the manufacturer datasheet for the authoritative pin description table, recommended operating conditions, and timing values before finalizing a board layout.
Where is the SN74LS541N pinout located?
The SN74LS541N pinout appears in the Texas Instruments manufacturer datasheet and in the 20-pin PDIP package diagram on this page. The device places inputs and outputs on opposite sides of the package, with pins 1 through 4 feeding outputs 6 through 9, pins 6 through 9 corresponding to inputs 17 through 20, and pins 13 through 16 feeding outputs 1 through 4. Verify every connection against the pin-description table before fabrication.
What does the SN74LS541N do?
The SN74LS541N buffers and drives eight non-inverting logic signals while allowing each output to enter a high-impedance state. According to the Texas Instruments manufacturer datasheet, the device operates from 4.75 V to 5.25 V and uses bipolar technology. It is intended for memory-address driving, clock driving, and bus-oriented transmission or reception where outputs must be disconnected cleanly from shared nodes.
Is SN74LS541N a drop-in replacement for SN74LS540N?
No, the SN74LS541N and SN74LS540N are not automatically drop-in replacements because their physical pin organizations differ. The Texas Instruments product information describes the SN74LS541 as having inputs and outputs on opposite sides of the package, unlike the related SN54LS240 and SN74LS240 family arrangement. Verify the exact pin table and routing before substituting one device for the other; package identity alone does not establish pin compatibility.
How does SN74LS541N compare with SN74LS241N?
The SN74LS541N provides the same general octal buffer, line-driver, and 3-state functions as the SN74LS241 family, but its input and output positions are arranged on opposite sides of the package. According to the manufacturer description for the SN74LS541 family, this physical organization distinguishes it from the LS240 and LS241 arrangement. A board substitution therefore requires pin-by-pin comparison rather than relying only on the device function.
What can replace SN74LS541N in a 20-pin PDIP design?
A valid replacement should provide eight non-inverting channels, a 3-state output function, compatible 4.75 V to 5.25 V operation, and the same 20-pin PDIP pin arrangement. The SN74LS541N family options identified for this design include the Texas Instruments SN54LS541N and legacy-source versions of SN74LS541N from ON Semiconductor, Motorola, and Hitachi. Verify supply limits, timing, enable polarity, temperature grade, and lifecycle requirements before approving a substitution.
Is SN74LS541N suitable for memory address and clock buffering?
Yes, the SN74LS541N is specifically suited to memory-address driving, clock driving, and bus-oriented interfaces. According to the Texas Instruments manufacturer datasheet, its eight channels are non-inverting, and its 3-state outputs can release shared lines when disabled. The 4.75 V to 5.25 V supply range also places it in conventional 5 V digital systems, although timing margin and load capability must be checked against the actual bus.
When should I choose SN74LS541N over another 74LS bus buffer?
Choose the SN74LS541N when the design requires eight non-inverting channels, 3-state outputs, a 4.75 V to 5.25 V supply, and a 20-pin PDIP arrangement with inputs and outputs on opposite sides of the package. Select another device only when its timing, output-drive limits, enable-control scheme, or temperature grade better satisfies the system. The SN74LS541N is a buffer, so it should not be treated as a voltage-level translator between incompatible logic families.
Where can I buy SN74LS541N online?
Use the Request a Quote form on this page to request SN74LS541N availability, quantity breaks, and current lead time. The part is an active Texas Instruments 20-pin PDIP logic device, but inventory and delivery schedules can change with market conditions. Submit the required quantity, target date, and shipment location so the commercial team can return a current quotation for the exact SN74LS541N ordering code.
What is the price of SN74LS541N?
The current commercial price for SN74LS541N should be obtained through the Request a Quote form on this page. The form allows buyers to specify the required quantity and obtain a current quotation without relying on a static marketplace figure. For engineering review, the exact part number, 20-pin PDIP package, and operating requirements should be stated in the request so the quotation corresponds to the intended configuration.
What is the lead time for SN74LS541N?
The current lead time for SN74LS541N should be confirmed through the Request a Quote form on this page by stating the required quantity and target delivery date. Lead time can vary with order quantity, inventory position, and production scheduling. For a complete procurement decision, also request the manufacturer part number confirmation and the intended 20-pin PDIP package configuration with the quotation.
Is SN74LS541N in stock?
Current SN74LS541N stock status should be checked through the Request a Quote form on this page. The manufacturer continues to list the SN74LS541 family, and the exact N suffix identifies the through-hole PDIP configuration, but inventory at any given moment can change. Submit the required quantity to receive current availability, expected delivery, and a quotation tied to the exact SN74LS541N part number.
What is the best ON Semiconductor equivalent for SN74LS541N?
The ON Semiconductor SN74LS541N is the closest legacy-source equivalent identified for this 20-pin PDIP design because it carries the same device name and function designation. According to the manufacturer material located for SN74LS541N, both devices are octal buffers and line drivers with 3-state outputs. Final approval still requires checking the complete pin table, electrical limits, timing, temperature grade, and supply requirements.
Does SN74LS541N have active-low output enables?
Yes, the SN74LS541N uses active-low output-enable inputs to control its 3-state outputs. According to the Texas Instruments manufacturer datasheet, the enables are arranged so four outputs can be disabled together, allowing two banks of four channels to be managed independently. Pulling an enable low places the associated outputs in the high-impedance state; pull it high to permit normal buffer operation.

엔지니어링 참조 데이터: SN74LS541N — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the SN74LS541N for a 5 V, through-hole design that needs eight non-inverting buffered channels with 3-state output control and a package layout that routes inputs and outputs from opposite sides. Its two active-low enables are useful for shared buses, clock branches, address routing, and test fixtures. Select SN54LS541N when the design requires the military-temperature family option instead of the commercial-grade SN74LS541N. Legacy-source SN74LS541N devices from ON Semiconductor or Motorola can support procurement diversification, but their lifecycle, sourcing status, and exact electrical characteristics must be confirmed. DM74LS541N and HD74LS541P are additional 74LS-family alternatives that require pin-table and temperature-grade review. Do not substitute solely because all candidates are described as octal 3-state buffers; verify pinout, timing, enable polarity, supply range, and lifecycle status.

대체품과의 비교

파라미터 이 제품 SN54LS541N SN74LS541N SN74LS541N DM74LS541N HD74LS541P
Brand Texas Instruments Texas Instruments onsemi Motorola onsemi Renesas Electronics
Package 20-pin PDIP (N) 20-pin PDIP (N) 20-pin PDIP (N) 20-pin PDIP (N) 20-pin PDIP (N) 20-pin PDIP (P)
Logic Function Non-inverting octal buffer and line driver Non-inverting octal buffer and line driver Non-inverting octal buffer and line driver Non-inverting octal buffer and line driver Non-inverting octal buffer and line driver Non-inverting octal buffer and line driver
Number of Channels 8 channels 8 channels 8 channels 8 channels 8 channels 8 channels
Supply Voltage Range 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V
Output State 3-state 3-state 3-state 3-state 3-state 3-state
Technology Bipolar Bipolar Bipolar Bipolar Bipolar Bipolar
Output-enable Inputs 2 active-low inputs controlling two banks of 4 outputs 2 active-low inputs controlling two banks of 4 outputs 2 active-low inputs controlling two banks of 4 outputs 2 active-low inputs controlling two banks of 4 outputs 2 active-low inputs controlling two banks of 4 outputs 2 active-low inputs controlling two banks of 4 outputs

주요 차별점

  • Inputs and outputs are placed on opposite sides of the package (vs SN74LS240N)
  • Two independently controlled output banks (vs SN74LS125N)
  • Commercial 5 V configuration with a military-grade family alternative (vs SN54LS541N)

설계 노트

Route each SN74LS541N input directly toward its corresponding output-side logic source, and keep the eight output traces short and continuous. The opposite-side input and output organization is useful for point-to-point PCB routing, but excessive series resistance, long stubs, or abrupt impedance changes can degrade signal integrity. Keep clock outputs especially short, provide a solid ground reference, and maintain clearance from adjacent switching-power nodes.

Do not leave either active-low output-enable input floating. The SN74LS541N uses two enables to control banks of four 3-state outputs, and undefined enable levels can produce unwanted output states or bus contention. Drive each enable from a defined logic level, sequence it correctly when multiple devices share a bus, and ensure the output-enable polarity has not been confused with an active-high enable on another octal-buffer family.

Use a stable 5 V supply because the SN74LS541N is specified for a 4.75 V to 5.25 V operating range. Place the required bypass capacitor close to the device power and ground pins using the manufacturer layout recommendation, and minimize supply-loop area. Account for input and output switching current when sizing the rail, especially when several channels change state simultaneously or nearby switching regulators create supply ripple.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

No component-specific environmental or material-compliance declarations were identified for the exact SN74LS541N ordering code. The device is a general-purpose bipolar logic IC rather than an automotive-qualified AEC-Q100 product.

관련 검색

sn74ls541n datasheet SN74LS541N datasheet pdf SN74LS541N pinout SN74LS541N specifications SN74LS541N replacement SN74LS541N equivalent SN74LS541N cross reference SN74LS541N footprint SN74LS541N vs SN74LS241N SN74LS541N price SN74LS541N stock Texas Instruments SN74LS541N

관련 부품 & 용어

Texas Instruments SN74LS541N SN54LS541N SN74LS541N DM74LS541N HD74LS541P octal buffer line driver logic IC digital logic TTL LS logic series 3-state output high-impedance state active-low output enable non-inverting buffer bipolar technology PDIP-20 DIP-20 through-hole package memory address driver clock driver bus interface 4.75 V to 5.25 V supply
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기