SN74LS541N - 8-Bit 3-State Buffer | Texas Instruments
MPN: SN74LS541N ✓ פעילSN74LS541N סקירה
An octal buffer and line driver is a digital logic IC positioned between a source device and a receiving bus. Its function belongs to the broader bus-interface and buffer-driver hierarchy, where it improves drive capability and provides controlled tri-state operation. The SN74LS541 is useful when a system must support bus-oriented transmission, memory addressing, clock distribution, or logic-level isolation without allowing undriven nodes to contend during inactive periods.
The primary features of the SN74LS541N include eight non-inverting channels, a 4.75 V to 5.25 V operating supply range, bipolar technology, and independently controlled 3-state outputs. Its two active-low output-enable inputs allow groups of four outputs to be disabled independently. This flexibility is valuable in multiplexed buses, bidirectional interface arrangements, and systems that require release of a shared data path during inactive intervals.
The SN74LS541 family differs from related LS540 and LS240-family arrangements through its physical pin organization, with inputs and outputs positioned on opposite sides of the package. That arrangement simplifies board routing when traces enter from one edge and leave through the other. The device is intended as a buffer rather than a level translator, so system designers must confirm that source and destination logic levels are compatible with the LS-family input and output thresholds.
Typical uses include memory address drivers, clock drivers, bus-oriented transmitters and receivers, control-signal isolation, and interfaces involving 5 V processors or programmable logic. Two enable inputs can manage four channels per bank, enabling partial bus participation. Because the outputs enter a high-impedance state only when the corresponding enable is pulled low, every enable input must be actively controlled and should not be left floating.
For PCB implementation, place the device close to the driven bus and maintain short, continuous output traces. Decoupling requirements and guaranteed electrical characteristics must be taken directly from the manufacturer datasheet. When substituting another 74LS-family device, verify the complete pin assignment, enable polarity, supply range, and output timing rather than relying only on the octal-buffer description.
This page organizes the SN74LS541N function, package, pin assignments, operating limits, commercial information, and drop-in comparison options into a design-focused reference. It also identifies practical bus-routing and enable-control considerations that are especially important when the device is used in shared 5 V digital systems.
חלופות תחליף ישיר עבור SN74LS541N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
SN54LS541N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SN74LS541N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←SN74LS541N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DM74LS541N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
HD74LS541P
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SN74LS541N דירוגים מרביים ומאפיינים חשמליים
| Number of Channels | 8 channels |
| Bits per Element | 8 bits per element |
| Logic Type | Non-inverting buffer and line driver |
| Output State | 3-state |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Technology | Bipolar |
| Output-enable Control | 2 active-low output-enable inputs |
| מארז | 20-pin PDIP |
| סוג הרכבה | Through-hole |
| פונקציה | Octal buffer and line driver |
| Input-to-Output Arrangement | Inputs and outputs on opposite sides of the package |
| High-Impedance Output Capability | 8 independently enabled outputs organized as two banks of 4 |
תצורת פינים של SN74LS541N
| פין 1 | 1A — Data input for output 1 |
| פין 2 | 2A — Data input for output 2 |
| פין 3 | 3A — Data input for output 3 |
| פין 4 | 4A — Data input for output 4 |
| פין 5 | GND — Ground |
| פין 6 | 1Y — Data output 1 |
| פין 7 | 2Y — Data output 2 |
| פין 8 | 3Y — Data output 3 |
| פין 9 | 4Y — Data output 4 |
| פין 10 | 3LE — Active-low output-enable input for outputs 1 through 4 |
| פין 11 | 4LE — Active-low output-enable input for outputs 5 through 8 |
| פין 12 | GND — Ground |
| פין 13 | 5Y — Data output 5 |
| פין 14 | 6Y — Data output 6 |
| פין 15 | 7Y — Data output 7 |
| פין 16 | 8Y — Data output 8 |
| פין 17 | 8A — Data input for output 8 |
| פין 18 | 7A — Data input for output 7 |
| פין 19 | 6A — Data input for output 6 |
| פין 20 | 5A — Data input for output 5 |
יישומים טיפוסיים
SN74LS541N מתאים עבור 6 יישוםs: Memory Address Buffering, Clock Signal Distribution, Shared Processor Bus Interface, Bidirectional Data-Path Isolation, Industrial Control Signal Distribution, Test and Measurement Fixture.
Memory Address Buffering
The SN74LS541N fits memory-address routing because it provides eight non-inverting channels and allows each output bank to be released through the active-low output-enable inputs. In a 4.75 V to 5.25 V memory system, the device can buffer processor or controller address lines before they reach memory and peripheral devices. The opposing input and output sides of the 20-pin PDIP simplify point-to-point board routing. Its 3-state capability is particularly useful when address buses are multiplexed or several destinations share a common bus. Confirm propagation delay and output-current limits against the actual memory timing before layout release.
מומלץ
Clock Signal Distribution
The SN74LS541N can distribute a 5 V clock across up to eight non-inverting channels, reducing the loading burden on a clock-generating logic device. Its eight buffers are grouped under two active-low output-enable inputs, so a design can independently keep four channels active while placing another four in the high-impedance state. This arrangement suits peripheral clock trees, control-signal distribution, and test systems that need to isolate inactive clock branches. Because the SN74LS541N is not a frequency translator, the source clock frequency, load capacitance, and timing budget must satisfy the manufacturer’s operating limits.
מומלץ
Shared Processor Bus Interface
The SN74LS541N is appropriate for a 5 V processor bus when the system requires eight buffered, non-inverting lines with controlled bus release. The two active-low enables can disconnect four outputs at a time, preventing inactive outputs from fighting a shared node and helping maintain predictable bus behavior. Its 20-pin PDIP package also suits through-hole legacy and industrial control assemblies. The device does not change logic voltage levels, so both the driver and receiver must use compatible thresholds. Engineers should verify timing, fanout, bus loading, and contention behavior in the completed system.
מומלץ
Bidirectional Data-Path Isolation
The SN74LS541N can support controlled directional paths by combining separate input and output channels with independent high-impedance control. In a bus-oriented transmitter or receiver arrangement, one output bank may be enabled while the opposite bank is disabled, limiting contention during direction changes. The 4.75 V to 5.25 V operating range suits conventional TTL-compatible 5 V systems, while the eight channels provide practical routing granularity. The circuit still needs external direction-control logic because the device does not autonomously determine bus direction. Confirm signal direction, setup and hold timing, and output loading against the manufacturer datasheet.
מומלץ
Industrial Control Signal Distribution
The SN74LS541N can distribute interlock, enable, and machine-control signals within a 5 V industrial control assembly. Eight non-inverting channels reduce the number of dedicated driver stages, while the two output-enable groups allow subsets of the control network to be disabled during transitions or maintenance states. The 20-pin PDIP package is well suited to through-hole control boards with long product lives. Industrial environmental requirements still need careful review: use the manufacturer temperature-range limits, maintain adequate supply bypassing, and keep switching-node or high-current power wiring away from sensitive logic traces.
מומלץ
Test and Measurement Fixture
The SN74LS541N is useful in a test fixture that drives eight instrumentation-control or address lines while selectively releasing unused outputs. Its 3-state outputs help prevent inactive fixture channels from loading the device under test, and its non-inverting organization simplifies control-logic integration. The two active-low enable groups make it possible to isolate four channels independently from the other four. For accurate measurements, account for the device’s propagation delay, output rise and fall behavior, and loading in the test setup. The 4.75 V to 5.25 V supply range requires a stable 5 V source with normal logic-level tolerances.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור SN74LS541N — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | SN54LS541N | SN74LS541N | SN74LS541N | DM74LS541N | HD74LS541P |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | onsemi | Motorola | onsemi | Renesas Electronics |
| Package | 20-pin PDIP (N) | 20-pin PDIP (N) | 20-pin PDIP (N) | 20-pin PDIP (N) | 20-pin PDIP (N) | 20-pin PDIP (P) |
| Logic Function | Non-inverting octal buffer and line driver | Non-inverting octal buffer and line driver | Non-inverting octal buffer and line driver | Non-inverting octal buffer and line driver | Non-inverting octal buffer and line driver | Non-inverting octal buffer and line driver |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Technology | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar |
| Output-enable Inputs | 2 active-low inputs controlling two banks of 4 outputs | 2 active-low inputs controlling two banks of 4 outputs | 2 active-low inputs controlling two banks of 4 outputs | 2 active-low inputs controlling two banks of 4 outputs | 2 active-low inputs controlling two banks of 4 outputs | 2 active-low inputs controlling two banks of 4 outputs |
מבדילים עיקריים
- Inputs and outputs are placed on opposite sides of the package (לעומתSN74LS240N)
- Two independently controlled output banks (לעומתSN74LS125N)
- Commercial 5 V configuration with a military-grade family alternative (לעומתSN54LS541N)
הערות תכנון
Route each SN74LS541N input directly toward its corresponding output-side logic source, and keep the eight output traces short and continuous. The opposite-side input and output organization is useful for point-to-point PCB routing, but excessive series resistance, long stubs, or abrupt impedance changes can degrade signal integrity. Keep clock outputs especially short, provide a solid ground reference, and maintain clearance from adjacent switching-power nodes.
Do not leave either active-low output-enable input floating. The SN74LS541N uses two enables to control banks of four 3-state outputs, and undefined enable levels can produce unwanted output states or bus contention. Drive each enable from a defined logic level, sequence it correctly when multiple devices share a bus, and ensure the output-enable polarity has not been confused with an active-high enable on another octal-buffer family.
Use a stable 5 V supply because the SN74LS541N is specified for a 4.75 V to 5.25 V operating range. Place the required bypass capacitor close to the device power and ground pins using the manufacturer layout recommendation, and minimize supply-loop area. Account for input and output switching current when sizing the rail, especially when several channels change state simultaneously or nearby switching regulators create supply ripple.
מידע על תאימות
No component-specific environmental or material-compliance declarations were identified for the exact SN74LS541N ordering code. The device is a general-purpose bipolar logic IC rather than an automotive-qualified AEC-Q100 product.