STM32L051K6U6 - 32MHz Cortex-M0+ MCU | STMicroelectronics
부품 번호: STM32L051K6U6 ✓ 활성STM32L051K6U6 개요
An ultra-low-power microcontroller is a semiconductor designed to complete control tasks while minimizing active and idle energy consumption. The STM32L0 family belongs to the 32-bit Arm Cortex-M microcontroller hierarchy and combines general-purpose processing, embedded memory, serial interfaces, timing peripherals, and analog conversion in one device. This integration reduces board area in battery-powered instruments, compact sensors, industrial controls, and accessory nodes.
The STM32L051K6U6 provides 32 KB of Flash for firmware, 8 KB of SRAM for working memory, and 2 KB of EEPROM for nonvolatile data retention. Its feature set includes ADC capability, I2C, SPI, UART, and PWM functions. The Arm Cortex-M0+ core executes 32-bit instructions at up to 32 MHz, supporting responsive digital control while retaining the efficiency expected from an ultra-low-power embedded platform.
The part is identified as a 32-UFQFPN surface-mount device in a 5 x 5 mm outline. Its compact land pattern is useful for space-constrained products, although the exposed-area thermal and assembly requirements must be followed in the PCB footprint and production process. The operating-temperature range listed for this ordering code extends from -40 C to 85 C, supporting industrial and commercial equipment where that range is adequate.
Typical applications include low-power sensor nodes, compact industrial controllers, battery-operated instruments, communication modules, and small motor or actuator-control products. The UART and SPI interfaces support external radios and storage, I2C supports low-speed sensors and peripherals, and the ADC supports analog monitoring. Firmware can use these interfaces together with PWM outputs and low-power modes to balance responsiveness against average energy use.
Designers should begin with the manufacturer pin-description table and package drawing before assigning tracks or defining the exposed-pad connection. Confirm the operating-voltage limits, decoupling requirements, clock configuration, programming interface, and unused-pin treatment in the manufacturer datasheet. Firmware migration to another STM32L0 member should be checked for peripheral differences even when the package and core are shared.
This product page combines the exact ordering information, interface features, pin-package characteristics, practical application guidance, and same-family drop-in alternatives for STM32L051K6U6 evaluation. It is designed to shorten component selection while preserving the electrical, mechanical, and firmware checks required for a reliable embedded design.
드롭인 대체품: STM32L051K6U6 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM32L051K6U6 (동일 폼 팩터 및 풋프린트) — 차이점: Flash Memory, Package, Product Type.
STM32L051K8U6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM32L031K6U6
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →STM32L021K6U6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM32L041K6U6
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →STM32L071K6U6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM32L051K6U6 최대 정격 & 전기적 특성
| Product Type | Ultra-low-power 32-bit microcontroller |
| Processor Core | Arm Cortex-M0+ RISC core |
| CPU Word Size | 32 bit |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 8 KB |
| EEPROM | 2 KB |
| ADC | 12-bit ADC |
| Serial Interfaces | I2C, SPI, and UART |
| Timer Output | PWM |
| 동작 온도 범위 | -40 C to +85 C |
| 패키지 | 32-UFQFPN, 5 x 5 mm |
| 핀 수 | 32 pins |
| 실장 유형 | Surface mount |
STM32L051K6U6 32-ufqfpn, 5 x 5 mm 핀 구성 가이드
STM32L051K6U6(32-ufqfpn, 5 x 5 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: STM32L051K6U6.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
STM32L051K6U6 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Node, Compact Industrial Controller, Low-Power Communication Module, Battery-Powered Measurement Instrument, Small Motor and Actuator Control, Embedded Accessory and Wearable Control.
Battery-Powered Sensor Node
The STM32L051K6U6 fits battery-powered sensor nodes because its ultra-low-power STM32L0 architecture combines a 32 MHz Arm Cortex-M0+ core with 32 KB of Flash, 8 KB of SRAM, and 2 KB of EEPROM. The ADC can acquire analog sensor data while I2C supports compatible low-speed sensing devices. A firmware schedule can keep the processor inactive between measurements and use UART or SPI for short data bursts, helping reduce average energy use. The 32-pin UFQFPN package also limits board area in a compact sensor enclosure. Power-source impedance, regulator dropout, and the selected sleep mode should be evaluated together because average battery life depends on the complete duty cycle rather than CPU frequency alone.
추천
Compact Industrial Controller
The STM32L051K6U6 is appropriate for a compact industrial controller where deterministic embedded control must coexist with limited board area. Its Cortex-M0+ core operates at 32 MHz, while PWM outputs can control actuators and the 12-bit ADC can monitor analog process inputs. I2C can connect configuration or sensor devices, SPI can support higher-speed peripherals, and UART provides a service or fieldbus link. The listed -40 C to 85 C temperature range supports many commercial and industrial environments. Firmware should define safe states for every actuator, provide watchdog recovery, and validate the 12-bit ADC accuracy against the actual signal chain and analog ground layout.
추천
Low-Power Communication Module
The STM32L051K6U6 can serve as the host controller in a compact wireless or serial communication module. Its 32-bit Cortex-M0+ processor provides sufficient control performance for packet handling, while UART offers a straightforward host interface and SPI supports common radio transceivers and flash-storage devices. The 32 KB of embedded Flash supports a focused protocol stack, and 8 KB of SRAM can accommodate working buffers without requiring an external memory device for modest workloads. Because radio modules are often duty-cycle sensitive, firmware should disable unused peripherals and use the low-power modes documented for the STM32L051K6 family. RF certification and electromagnetic compatibility remain system-level requirements.
추천
Battery-Powered Measurement Instrument
The STM32L051K6U6 is well suited to compact measurement instruments that combine low standby demand with a responsive user interface. The 12-bit ADC handles analog measurement channels, UART or SPI can connect to a display or external memory, and PWM can drive indicator LEDs or excitation circuits. Its 32 KB of Flash provides enough space for focused acquisition and calibration routines, while 2 KB of EEPROM can retain configuration parameters. The 5 x 5 mm UFQFPN package helps reduce instrument size, but the exposed-area connection and thermal design must follow the package drawing. For accurate measurements, use separate analog and digital grounding strategies and calibrate gain and offset in production.
추천
Small Motor and Actuator Control
The STM32L051K6U6 can control small motors, solenoids, valves, or other actuator loads when its PWM outputs and ADC inputs are assigned through the manufacturer alternate-function tables. The 32 MHz Cortex-M0+ core provides responsive timing for commutation, position sensing, and fault handling, while the 8 KB of SRAM supports compact control-state machines. I2C and SPI allow expansion to sensors or gate drivers, and UART simplifies commissioning with a host computer. The principal trade-off is limited output drive, so transistor or MOSFET stages should provide load current and voltage protection. Production designs should include overcurrent, open-load, and watchdog recovery behavior rather than relying on firmware alone.
추천
Embedded Accessory and Wearable Control
The STM32L051K6U6 is suitable for compact accessory controllers that need low standby consumption and a limited set of communications. A 32 MHz Cortex-M0+ core can manage button input, status LEDs, sensor polling, and configuration updates, while UART and I2C cover common external-device connections. The 32-pin UFQFPN footprint supports dense layouts, and 32 KB of Flash accommodates a small user application without an external microcontroller. For wearable or battery-operated products, firmware should keep unused GPIO and peripherals disabled between events and use a low-power wake source. Mechanical button debouncing, ESD protection, and safe behavior during battery depletion should be included in the hardware and firmware design.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM32L051K6U6 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | STM32L051K8U6 | STM32L031K6U6 | STM32L021K6U6 | STM32L041K6U6 | STM32L071K6U6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) | 32-UFQFPN (5x5) |
| CPU Core | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 64 KB | 32 KB | 32 KB | 32 KB | 128 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| ADC | 12-bit ADC | 12-bit ADC | 12-bit ADC | 12-bit ADC | 12-bit ADC | 12-bit ADC |
| Serial Interfaces | I2C, SPI, and UART | I2C, SPI, and UART | I2C, SPI, and UART | I2C, SPI, and UART | I2C, SPI, and UART | I2C, SPI, and UART |
| Operating Temperature Range | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Pin Count | 32 pins | 32 pins | 32 pins | 32 pins | 32 pins | 32 pins |
주요 차별점
- Provides a balanced 32 KB Flash configuration without reducing CPU frequency (vs STM32L071K6U6)
- Uses the full STM32L051 feature set rather than the reduced STM32L031 configuration (vs STM32L031K6U6)
- Retains 32 KB of Flash while offering a larger-program-memory alternative (vs STM32L051K8U6)
- Maintains the STM32L0 Cortex-M0+ architecture and compact package family (vs STM32F051K4U6)
설계 노트
Route the exposed area of the 32-UFQFPN package using the manufacturer land-pattern and thermal-pad guidance. Place the MCU close to the intended power entry point, preserve short return paths for ground pins, and avoid separating the exposed area from the primary ground plane with unnecessary slots. Confirm drill, solder-mask, paste, and assembly dimensions against the current package drawing rather than adapting a generic QFN footprint.
Plan the power tree so the MCU supply remains within the manufacturer operating range during startup, sleep transitions, and maximum peripheral activity. Place local decoupling directly at the supply and ground pins, with the capacitor placement and values selected from the manufacturer application guidance. For battery-powered systems, calculate average current from active current, sleep current, wake duration, and measurement interval rather than using CPU frequency alone.
Separate analog inputs from fast-switching digital nets, keep the ADC return path within the quiet analog-ground region, and avoid routing high-current outputs beneath the MCU or ADC inputs. Provide short, symmetrical connections where timing or communication interfaces require controlled impedance. Since the individual pin assignments are defined in the manufacturer pin table, verify every alternate-function route and programming signal before releasing the layout.
Do not assume that another STM32L0 device with the same UFQFPN outline is firmware-compatible without checking peripheral instances, clock topology, interrupts, bootloader behavior, and memory organization. The STM32L031K6U6, STM32L021K6U6, STM32L041K6U6, and STM32L071K6U6 differ from the STM32L051K6U6 in resource availability even when the physical footprint is shared. Run peripheral characterization and full firmware regression after any substitution.
For SPI, UART, or other externally exposed interfaces, control edge rates through the source configuration and use appropriate termination when the board trace, cable, or connector creates a reflective path. Keep clock lines short and isolate them from sensitive ADC inputs. Validate the final design with the intended baud rate, cable length, supply range, and worst-case loading because nominal interface capability alone does not guarantee system-level signal integrity.
규정 준수 정보
The STM32L051K6U6 is an industrial and commercial microcontroller rather than an AEC-Q100 automotive-qualified ordering code. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation.