STM8L101F2P3 - 8-Bit 16MHz 4KB MCU | STMicroelectronics
부품 번호: STM8L101F2P3 ✓ 활성STM8L101F2P3 개요
An ultra-low-power microcontroller is designed to spend substantial operating time in low-energy states while still providing real-time control and communications. The STM8L101 family is positioned between general-purpose 8-bit microcontrollers and more complex low-power processors. Its STM8 core provides up to 16 MIPS at 16 MHz, while integrated timers, comparators, USART, SPI, and I2C interfaces reduce the need for external peripheral components.
The STM8L101F2P3 provides 4 KB of Flash for program storage and operates as an 8-bit CISC controller in a 20-pin TSSOP package. The STM8L101 family also supports options extending to 8 KB of Flash, making the STM8L101F2P3 a practical choice when program storage is sufficient but low power, compactness, and a broad set of communication interfaces are priorities.
Its 20-pin TSSOP package supports integration in compact control boards while exposing the family's principal communications and timing resources. The STM8 core uses a 24-bit linear address space and an instruction set designed for efficient embedded code density. Low-power operating modes help reduce average energy consumption in battery-powered sensors, portable instruments, and always-on monitoring equipment.
Typical applications include low-power sensor nodes, compact industrial controllers, battery-operated instruments, communication modules, and embedded measurement systems. USART, SPI, and I2C connectivity allow the controller to interface with sensors, transceivers, memories, and human-interface or data-acquisition circuitry. Its 16 MHz operating rate supports responsive control without requiring a larger processor or external programmable logic.
PCB design should preserve low-power behavior and reliable communication. Place decoupling capacitors close to the supply pins, route sensitive signals away from fast-switching nodes, and confirm pin multiplexing and peripheral assignments against the manufacturer pin description before finalizing the PCB. Programming and peripheral configuration should be validated with the applicable STMicroelectronics toolchain and device programming interface.
This product page combines the key MCU specifications, confirmed package details, practical application guidance, and same-package alternative analysis to support component selection, schematic review, PCB planning, and sourcing decisions for embedded engineers.
드롭인 대체품: STM8L101F2P3 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM8L101F2P3 (동일 폼 팩터 및 풋프린트) — 차이점: Architecture.
STM8L101F3P3
✅ 드롭인가격 문의
데이터시트 보기 →STM8L101F1P3
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM8L101F4P3
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM8L101F5P3
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM8L101F6P3
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM8L101F2P3 최대 정격 & 전기적 특성
| Product Type | 8-bit ultra-low-power microcontroller |
| Architecture | STM8 CISC |
| Maximum CPU Frequency | 16 MHz |
| Maximum CPU Performance | 16 MIPS at 16 MHz |
| Flash Memory | 4 KB |
| Program Memory Organization | 4K x 8 |
| 패키지 | 20-pin TSSOP |
| Package Type | TSSOP-20 |
| Programming Voltage Levels | 1.8 V / 2.5 V |
| Addressing Capability | 24-bit linear addressing space |
| Integrated Interfaces | USART, SPI, I2C |
| Integrated Peripherals | Multifunction timers and comparators |
| Delivery Format | Tube |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
STM8L101F2P3 tssop-20 핀 구성 가이드
STM8L101F2P3(tssop-20 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: STM8L101F2P3.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
STM8L101F2P3 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Nodes, Portable Measurement Instruments, Industrial Condition Monitoring, Low-Power Communication Modules, Compact Environmental Control, Smart Home Sensor Hubs.
Battery-Powered Sensor Nodes
The STM8L101F2P3 fits battery-powered sensor nodes because its ultra-low-power STM8L101 architecture supports energy-conscious operation while retaining a 16 MHz, 8-bit processing core. Its USART, SPI, and I2C interfaces can connect a sensor, radio module, or external memory without requiring several dedicated peripheral chips. The 4 KB Flash limit is appropriate for compact acquisition, filtering, threshold detection, and communication-control firmware. A battery-life estimate should include the microcontroller's measured sleep and active currents together with sensor and radio loading, since the complete system's duty cycle determines the final power budget.
추천
Portable Measurement Instruments
The STM8L101F2P3 is appropriate for portable measurement instruments that combine low-power operation, local signal processing, and serial data transfer. Its 16 MHz execution rate provides responsive handling of measurements, while USART, SPI, and I2C support sensors, displays, memories, and data-capture interfaces. The 4 KB program-memory configuration is suitable for compact instrument firmware that concentrates on acquisition, calibration tables, status reporting, and control. For instruments with complex user interfaces or extensive calibration algorithms, measure the linked firmware size early because the higher-memory STM8L101 variants provide more room without changing the TSSOP-20 footprint.
추천
Industrial Condition Monitoring
The STM8L101F2P3 can serve as the local controller in industrial condition-monitoring equipment, combining a low-power 8-bit core with timers, comparators, and multiple serial interfaces. Comparators can support threshold detection, timers can handle periodic sampling or actuator timing, and SPI or I2C can connect sensors and local storage. Its 4 KB Flash is suitable for compact firmware that performs sampling, filtering, event detection, and status communication. Industrial deployments should verify the exact temperature range, supply limits, and peripheral assignments for the selected grade, then isolate communication interfaces appropriately for the installation environment.
추천
Low-Power Communication Modules
The STM8L101F2P3 suits compact communication modules where an interface controller must coordinate sensors, radios, or host processors under constrained power and memory budgets. USART provides a straightforward host or module connection, while SPI and I2C support higher-speed peripherals and external memory. The 16 MHz STM8 core provides enough responsiveness for framing, buffering, status management, and low-level protocol handling. Firmware should include timeout, idle-state, and bus-error recovery paths, and the final board should verify signal levels and pin multiplexing against the exact STM8L101F2 variant.
추천
Compact Environmental Control
The STM8L101F2P3 is well suited to compact environmental controllers that monitor temperature, humidity, light, or air-quality sensors and operate relays, indicators, or local actuators. Its timers and comparators support periodic measurements and threshold events, while I2C and SPI accommodate common sensor and display interfaces. The 20-pin TSSOP package helps maintain a small controller footprint, and the 4 KB Flash configuration can support focused acquisition and control code. Design the firmware to provide hysteresis, sensor fault handling, and safe actuator states so that a communication failure cannot create an unsafe control condition.
추천
Smart Home Sensor Hubs
The STM8L101F2P3 can act as a small smart-home sensor hub for translating information from local sensors into a serial or low-speed network link. Its combination of USART, SPI, I2C, timers, and comparators supports mixed sensor inputs, while the low-power STM8L101 platform is appropriate for battery-powered rooms or energy-monitoring accessories. The 4 KB Flash capacity favors compact protocol handling and event logic rather than a large local user interface. Before deployment, test sleep-mode wake behavior, peripheral retention, and communication recovery because those conditions determine whether the hub remains responsive in a duty-cycled installation.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM8L101F2P3 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | STM8L101F3P3 | STM8L101F1P3 | STM8L101F4P3 | STM8L101F5P3 | STM8L101F6P3 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| CPU Architecture | 8-bit STM8 CISC | 8-bit STM8 CISC | 8-bit STM8 CISC | 8-bit STM8 CISC | 8-bit STM8 CISC | 8-bit STM8 CISC |
| Maximum CPU Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Maximum CPU Performance | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS |
주요 차별점
- Lower memory footprint within the same STM8L101 architecture (vs STM8L101F1P3)
- Balanced program-memory capacity (vs STM8L101F3P3)
- Matches the STM8S memory size without assuming family equivalence (vs STM8S103F2P6TR)
- Full family integration in a compact package (vs STM8L101F4P3)
설계 노트
Place the supply bypass capacitor immediately beside the STM8L101F2P3 power and ground pins, and use a short, low-loop connection to reduce switching impedance. Keep traces to external sensors and communication devices away from the MCU supply return where practical. The 20-pin TSSOP footprint has fine lead spacing, so verify pad dimensions, solder-mask clearance, and assembly tolerances against the manufacturer land pattern before releasing the PCB.
Calculate the average supply current from active and low-power operating states rather than using only the 16 MHz processing capability. The STM8L101F2P3 has 4 KB of Flash, so firmware size should be checked against both program-memory and RAM limits. Confirm the exact supply range, programming voltage, and current consumption for the selected device and temperature grade in the manufacturer documentation before defining the power tree.
Do not treat equal package dimensions and Flash capacity as proof of interchangeability between STM8 families. STM8S103F2P6TR has a 20-pin TSSOP package and 4 KB Flash, but its peripheral mapping, performance, and electrical requirements must be checked separately. For STM8L101F1P3 through F6P3 alternatives, compare memory, RAM, supply limits, peripheral assignments, temperature range, and programming requirements before approving a substitution.
Assign SPI, I2C, and USART functions only after checking the device pin-description table because several STM8L101 signals are multiplexed. Provide suitable pull-ups or level translation where the connected peripheral requires them, and route communication lines away from switching nodes and long power loops. Firmware should also enable conservative bus speeds during bring-up to distinguish timing problems from incorrect peripheral configuration.
규정 준수 정보
Compliance status has not been established by the manufacturer product page or component listings identified for STM8L101F2P3.