Microchip Technology

SY88713VKC - 622 Mbps PECL Post Amplifier | Microchip Technology

부품 번호: SY88713VKC ✓ 활성
3.3 V Vdss 8 pins Package
MOQ: 1 |

SY88713VKC 개요

The Microchip Technology SY88713VKC is a low-power PECL limiting post amplifier designed for operation at up to 622 Mbps using either a 3.3 V or 5 V supply. The device is intended to restore and shape high-speed differential signal integrity in PECL-based communications equipment. It is available in an 8-pin surface-mount package, and the listed device provides PECL-compatible outputs together with a PECL signal-detect function and a TTL-compatible enable input.

A PECL post amplifier is a signal-conditioning IC used in the receiver section of a high-speed digital link. Its limiter and amplification stage increase signal amplitude, reduce timing uncertainty, and regenerate a clean output waveform for the next circuit block. PECL, or positive emitter-coupled logic, is a differential high-speed logic family commonly used in telecommunications, serial links, clock distribution, and optical-network equipment. The SY88713VKC supports 622 Mbps operation, allowing it to address legacy and intermediate-rate fiber-optic and backplane interfaces.

The principal listed features are single-rail or 5 V power-supply operation, low-noise PECL data outputs, chatter-free PECL signal-detect output, and a TTL /EN input for control by conventional digital logic. These functions allow a system designer to monitor receiver activity and conditionally enable or disable downstream signal paths. The 3.3 V operating option is particularly useful where the interface logic uses a lower supply voltage while the surrounding board still uses 5 V PECL circuitry.

The SY88713VKC is a limiting post amplifier rather than a general-purpose linear amplifier. Its purpose is to recover a valid digital waveform from a degraded high-speed differential signal. Noise, jitter, attenuation, and reflections accumulated along a transmission path can reduce signal margin, so the amplifier restores amplitude and provides a defined output state before the signal reaches a clock recovery, deserializer, or other logic device.

Typical uses include telecommunications line cards, optical transceiver receiver channels, network interface equipment, clock-recovery circuits, and legacy SONET or related high-speed backplanes. In each case, the post amplifier can sit between a transmission line and downstream digital logic, provided the board layout preserves the differential impedance, provides proper PECL termination, and keeps the enable and signal-detect traces away from sensitive clock inputs.

PCB implementation should follow the manufacturer datasheet's recommended layout, including controlled-length differential routing, short return paths, and appropriate supply decoupling. Termination values, trace impedance, and device placement should be selected for the actual board stack-up rather than copied without calculation. The enable pin and signal-detect output also require logic-level review, because their interfacing behavior determines whether the receiver can be safely muted during reset or fault conditions.

This page identifies the SY88713VKC's core role, supply options, supported data rate, package, control features, pricing reference, and application context. Detailed absolute maximum ratings, propagation delay, jitter, input-output logic levels, and thermal limits should be confirmed in the manufacturer datasheet before the IC is released for a new high-speed circuit.

드롭인 대체품: SY88713VKC — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 제품에는 사용 가능한 드롭인 대체품이 없습니다.

대체품 요청

SY88713VKC 최대 정격 & 전기적 특성

Product Type PECL limiting post amplifier
Maximum Data Rate 622 Mbps
Low-Voltage Supply Option 3.3 V
High-Voltage Supply Option 5 V
Supply Configuration Single or 5 V
Output Logic Low-noise PECL
Signal Detect Output Chatter-free PECL
Enable Input TTL-compatible /EN
Logic Family PECL
Package Pin Count 8 pins
실장 유형 Surface mount

SY88713VKC 8 pins 핀 구성 가이드

SY88713VKC(8 pins 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

SY88713VKC의 8 pins 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: SY88713VKC.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

SY88713VKC 적합 용도: 6 애플리케이션s: Telecom Receiver Line Cards, Optical Transceiver Receive Channels, High-Speed Backplane Receive Interfaces, Clock Recovery Input Conditioning, Network Equipment Redundant Receivers, Legacy High-Speed Test Equipment.

🌐

Telecom Receiver Line Cards

The SY88713VKC fits telecom line-card receiver paths that operate at up to 622 Mbps and require regenerated PECL signals. Place the device near the line-card input or connector launch, then use controlled differential routing and the prescribed PECL termination arrangement. Its limiting post-amplifier function restores amplitude before clock recovery or deserialization, while the chatter-free signal-detect output provides a direct activity indication. The TTL-compatible /EN input also allows the receiver chain to be disabled during reset. Designers should confirm propagation delay, jitter, output common-mode voltage, and supply-current margin against the individual channel requirements before releasing the layout.

🌐

Optical Transceiver Receive Channels

The SY88713VKC is suitable for regenerating a degraded differential signal at the receive side of an optical transceiver link operating up to 622 Mbps. Its 3.3 V or 5 V supply options support both legacy 5 V PECL systems and lower-voltage interface designs. The device provides low-noise PECL outputs and a chatter-free signal-detect output, allowing the receive path to be monitored before downstream clock-and-data-recovery circuitry. Layout should minimize the distance between the transceiver receiver, the post amplifier, and termination components, and should preserve controlled differential impedance through connector and package transitions.

🖥️

High-Speed Backplane Receive Interfaces

The SY88713VKC can condition signals received through a controlled-impedance backplane when the target bit rate is 622 Mbps or lower. Cable loss, connector reflections, and crosstalk can reduce eye opening before the signal reaches digital logic, making a limiting stage useful. The post amplifier restores signal amplitude and supplies clean PECL outputs, while signal detect reports whether valid activity is present. The 8-pin surface-mount package should be surrounded by short differential traces and correctly placed termination or bias networks. Engineers should verify the complete channel budget, including attenuation, jitter, reflections, and receiver sensitivity, rather than relying on data-rate matching alone.

🖥️

Clock Recovery Input Conditioning

The SY88713VKC is useful ahead of a clock-recovery or clock-and-data-recovery block when a 622 Mbps source requires deterministic PECL limiting. Regenerating the signal before the recovery circuit can reduce sensitivity to amplitude variation along the transmission path and supply a clean differential waveform with low-noise outputs. The signal-detect output can indicate whether the recovered clock source is active, while /EN allows controlled muting during initialization. Because phase noise and timing jitter accumulate through the channel, the amplifier must be placed close to the receiving device and its differential routing must follow the manufacturer's recommended layout to preserve the available timing margin.

🌐

Network Equipment Redundant Receivers

The SY88713VKC can be used in redundant or failover receiver branches where each incoming PECL link must be conditioned independently before selection logic. Its signal-detect output can assist the supervising circuit in determining which branch is active, and the TTL-compatible /EN input allows a branch to be disabled during switching. The device supports 3.3 V or 5 V operation, which helps align with mixed-voltage interface sections. Control timing, glitch behavior around enable transitions, and input common-mode range must be reviewed carefully. A clean implementation keeps the two receive branches physically separated enough to limit shared-impedance coupling and uses short output routes to the selection circuitry.

🔧

Legacy High-Speed Test Equipment

The SY88713VKC fits legacy test and measurement equipment that requires a PECL limiting stage for signals at or below 622 Mbps. It can condition a source output before an older logic analyzer, counter, or timing-measurement circuit, providing a more defined differential waveform and an activity indication. The device should remain close to the measured node to reduce additional propagation delay and sensitivity to board reflections. The TTL-compatible enable input can support repeatable test sequences by muting the output when it is not required. Engineers should account for the amplifier's propagation delay, jitter behavior, supply requirements, and output common-mode levels when calibrating timing measurements or interpreting captured waveforms.

What is the SY88713VKC used for?
The SY88713VKC is a low-power PECL limiting post amplifier used to restore degraded differential signals in high-speed digital receivers. According to the Micrel Semiconductor datasheet, it supports 3.3 V or 5 V operation at up to 622 Mbps and provides low-noise PECL outputs. It is appropriate for receiver links that require amplitude restoration, defined limiting behavior, or a clean signal before clock recovery and deserialization.
What is the maximum data rate of the SY88713VKC?
The SY88713VKC supports data rates up to 622 Mbps. The Micrel Semiconductor datasheet identifies the device as a 3.3 V/5 V, 622 Mbps PECL low-power limiting post amplifier. This rate makes it relevant to telecom line cards, high-speed backplanes, clock-distribution circuits, and optical-transceiver receiver paths, although the actual link margin still depends on the total jitter, noise, loss, and termination network.
Can the SY88713VKC operate from both 3.3 V and 5 V?
Yes, the SY88713VKC supports operation from a single 3.3 V supply or from a 5 V supply. The Micrel Semiconductor datasheet specifically describes single or 5 V power operation at 622 Mbps. The appropriate supply depends on the voltage levels used by the surrounding receiver chain and should be checked against the device's input and output common-mode specifications.
Where can I download the SY88713VKC datasheet PDF?
The SY88713VKC datasheet PDF can be accessed through the manufacturer-linked documentation listed on this page or through the datasheet archive record for the Micrel Semiconductor device. The document is an 8-page datasheet covering the 3.3 V/5 V, 622 Mbps limiting post amplifier. Use the manufacturer datasheet as the controlling document for absolute maximum ratings, timing, supply current, pin connections, and recommended layout.
Where can I find the SY88713VKC pinout?
The SY88713VKC pin assignment is documented in the manufacturer datasheet's pin-configuration and electrical-characteristics sections. The device is an 8-pin surface-mount part with differential PECL signal-path pins, a PECL signal-detect output, and a TTL-compatible enable input. Use the pin-description table and package drawing together when assigning PCB nets, because the exposed package dimensions and lead assignments must match the exact ordering code.
Where can I buy SY88713VKC online?
The SY88713VKC can be requested through the Request a Quote form on this page. The form is the appropriate route for checking exact ordering-code availability, current lead time, minimum order quantity, and delivery options for the standard SY88713VKC and any tape-and-reel packaging code. It also avoids confusion with the separately listed SY88713VKC TR variant.
What is the price of the SY88713VKC?
The current commercial price for the SY88713VKC should be obtained through the Request a Quote form on this page. A published unit-price reference is maintained separately in the structured pricing field, while live quotations, stock, and lead time may change with supplier conditions. The quote request should identify the desired package quantity and whether the standard device or SY88713VKC TR ordering code is required.
Is the SY88713VKC in stock and what is its lead time?
Current stock and lead time for the SY88713VKC should be confirmed through the Request a Quote form on this page. A listing may indicate availability without representing guaranteed inventory for the exact ordering code and quantity. Include the required quantity, shipment destination, and production schedule when requesting the quotation so the supplier can provide a meaningful allocation and lead-time response.
What is the best drop-in replacement for the SY88713VKC?
No independently verified drop-in replacement for the SY88713VKC is established by the available cross-reference records. A valid replacement must match the 8-pin package, pin assignments, 3.3 V/5 V supply operation, PECL interfaces, enable function, signal-detect function, and 622 Mbps performance rather than merely sharing the data rate. Submit the candidate MPN for engineering review before treating it as a drop-in substitute.
Can an equivalent PECL post amplifier replace the SY88713VKC?
An equivalent PECL post amplifier can replace the SY88713VKC only after its pinout and timing behavior are verified against the original datasheet. The critical checks include 8-pin footprint compatibility, differential input polarity, PECL output common-mode levels, TTL /EN behavior, PECL signal-detect output, supply-current margin, propagation delay, and deterministic operation at 622 Mbps. A similar feature description alone does not establish drop-in compatibility.
When should I choose the SY88713VKC instead of a generic PECL buffer?
Choose the SY88713VKC when a degraded 622 Mbps differential signal needs limiting, regeneration, low-noise PECL outputs, and a dedicated signal-detect function. A generic PECL buffer may reproduce edges but can lack the receiver-oriented limiting behavior, chatter-free signal detection, or TTL-compatible enable interface. The additional features simplify fault monitoring and controlled shutdown in telecom and optical-receiver designs.
Is the SY88713VKC suitable for optical transceiver receivers?
Yes, the SY88713VKC is suitable for high-speed optical-transceiver receiver paths operating up to 622 Mbps. Its limiting post-amplifier architecture and PECL outputs are intended to restore signals received from lossy or noisy channels before downstream digital logic. The board must still use correct differential impedance, PECL biasing, termination, and short return paths to preserve signal integrity.
What are the key specifications of SY88713VKC that engineers should know?
The key SY88713VKC specifications are 3.3 V/5 V supply operation, operation up to 622 Mbps, low-noise PECL data outputs, a chatter-free PECL signal-detect output, and a TTL-compatible /EN input. The Micrel Semiconductor datasheet describes the device as a low-power limiting post amplifier. Its 8-pin surface-mount implementation places it in the interface IC and amplifier categories for high-speed digital receiver designs.
SY88713VKC versus a generic PECL post amplifier — which is better for telecom designs?
The SY88713VKC is generally better when the design needs a complete receiver-oriented feature set at up to 622 Mbps: limiting, low-noise PECL outputs, chatter-free signal detection, and TTL-compatible enable control. A generic PECL post amplifier may offer fewer control functions and require external detection or shutdown logic. Final selection should compare supply current, timing, jitter, common-mode levels, and exact pin compatibility.
How should the SY88713VKC be laid out for reliable 622 Mbps operation?
The SY88713VKC should be placed close to the receiver connection and routed with controlled differential impedance, short connections, continuous return paths, and the supply-decoupling arrangement shown in the manufacturer application guidance. Keep the enable and signal-detect traces away from sensitive clock and data nets. For 622 Mbps, via stubs, layer transitions, connector launches, and termination details can materially affect jitter and signal integrity.

엔지니어링 참조 데이터: SY88713VKC — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the SY88713VKC for a 622 Mbps PECL receiver path that needs integrated limiting, low-noise regenerated outputs, chatter-free signal detection, and TTL-compatible enable control. Its 3.3 V or 5 V supply flexibility is useful in telecom line cards, optical-transceiver receivers, backplane interfaces, and legacy test equipment. Choose a generic PECL buffer instead only when regeneration, signal detect, and enable control are unnecessary and the simpler device has a verified timing and common-mode margin. Do not approve a substitute based only on the 622 Mbps rating; confirm the 8-pin footprint, pin functions, differential polarity, enable thresholds, signal-detect behavior, supply current, propagation delay, and output levels. The SY88713VKC TR is a distinct ordering code and should be selected only when its physical packing matches the assembly process.

주요 차별점

  • Integrated receiver monitoring (vs Generic PECL post amplifier)
  • Integrated shutdown control (vs Generic PECL post amplifier)
  • Dual supply compatibility (vs 5 V-only PECL post amplifier)

설계 노트

Treat the SY88713VKC as a high-speed differential signal-conditioning element. Route the input and output pairs as controlled-impedance traces, minimize vias and stubs, and keep the device close to the receiving or line-card connection. At 622 Mbps, small discontinuities and return-path discontinuities can add reflections and jitter even when the amplifier itself meets its specified data rate.

Use the manufacturer datasheet's recommended PECL termination, supply-decoupling, and pin-placement arrangement. The enable and signal-detect traces should be routed away from sensitive differential clock and data nets. Confirm that output common-mode voltage and input common-mode range match the adjacent device, and avoid placing slow control signals directly beneath the high-speed differential pair.

Do not select a replacement solely because it is described as a 622 Mbps PECL post amplifier. Verify the 8-pin pinout, differential input polarity, TTL /EN threshold, PECL signal-detect implementation, supply current, propagation delay, and output levels. Also distinguish the SY88713VKC from the SY88713VKC TR ordering code so that the requested physical packaging matches the assembly plan.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The available product descriptions do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Automotive qualification is not inferred from the high-speed communications application.

관련 검색

SY88713VKC datasheet SY88713VKC pinout SY88713VKC datasheet pdf SY88713VKC equivalent SY88713VKC replacement SY88713VKC cross reference SY88713VKC price SY88713VKC stock Microchip SY88713VKC SY88713VKC 622 Mbps PECL amplifier SY88713VKC 3.3V 5V amplifier SY88713VKC signal detect

관련 부품 & 용어

Microchip Technology Micrel Semiconductor SY88713VKC SY88713VKC TR PECL limiting post amplifier high-speed interface IC signal conditioner clock and data recovery differential signaling positive emitter-coupled logic 3.3 V power supply 5 V power supply 622 Mbps low-noise PECL output PECL signal detect TTL enable input surface-mount package telecommunications equipment optical transceiver receiver high-speed backplane controlled impedance signal integrity
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기