Texas Instruments

TAS5186ADDV - 210W 6-Channel Class-D Amplifier | TI

부품 번호: TAS5186ADDV ✓ 활성
0 V to 34 V Vdss 44-pin HTSSOP (DDV) Package
MOQ: 1 |

TAS5186ADDV 개요

The Texas Instruments TAS5186ADDV is a 210-W, six-channel digital power-stage Class-D audio amplifier with a 0-V to 34-V supply range, PWM input architecture, and a 44-pin HTSSOP (DDV) package. The device is designed for multichannel home-theater and powered-speaker systems where one amplifier IC can address a 5.1-channel audio signal chain.

A Class-D digital power stage is an audio amplifier that uses pulse-width modulation to drive a switching output stage. Unlike a conventional linear audio amplifier, a Class-D stage can convert more of its input power into output power, reducing the amount of heat that must be removed from the amplifier assembly. The TAS5186A family integrates six output channels for compact multichannel audio systems.

The TAS5186ADDV supports up to 210 W of total amplifier power, is characterized as a six-channel 30-W device, and can drive a 3-ohm load. Texas Instruments describes the power stage as capable of driving a single-ended subwoofer above 60 W at 10% THD+N. Its specified total harmonic distortion plus noise is 0.07%, making it suitable for consumer audio equipment where channel matching and low crossover distortion are important.

The device accepts PWM control signals, allowing it to operate with a compatible digital audio modulator such as the TAS5086. This architecture separates audio decoding and modulation from power amplification. It also means the selected modulator must support the signal format, switching frequency, channel count, and control requirements expected by the TAS5186A family.

Typical applications include 5.1-channel home-theater amplifiers, powered subwoofers, multichannel active speakers, and compact consumer audio receivers. Its 44-pin HTSSOP package supports surface-mount assembly, while the stated 0°C to 70°C operating range targets commercial indoor environments. Heat management remains important because sustained multichannel output can raise junction and PCB temperatures.

For a robust design, follow the manufacturer datasheet when assigning the power, ground, PWM input, and thermal-pad connections. Place input and power-ground connections to minimize switching-current loops, use the recommended decoupling arrangement, and provide sufficient copper area under the exposed pad. Verify thermal performance across the highest expected channel load rather than relying only on nominal output power.

This product page combines manufacturer specifications, application guidance, practical thermal and layout considerations, and directly documented family alternatives for engineers evaluating the TAS5186ADDV as the power stage of a multichannel Class-D audio system.

드롭인 대체품: TAS5186ADDV — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

TAS5186ADDVR

✅ 드롭인
📦 HTSSOP-44 (DDV)
Same 210-W, six-channel electrical ratings with 0% stated power difference; ordering suffix changes the packing format.

📋 참조 대체품 (카탈로그에 없음)

TAS5186ADDVG4

✅ 드롭인
📦 HTSSOP-44 (DDV)
Same 210-W, six-channel electrical ratings with 0% stated power difference; ordering suffix changes the packing format.

📋 참조 대체품 (카탈로그에 없음)

TAS5186DDVG4

✅ 드롭인
📦 HTSSOP-44 (DDV)
Same 210-W, six-channel family ratings with 0% stated power difference; ordering suffix and qualification details differ.

📋 참조 대체품 (카탈로그에 없음)

TAS5186ADDV 최대 정격 & 전기적 특성

Product Type 6-Channel Class-D Audio Power Stage
Total Output Power 210 W
Number of Output Channels 6 channels
Per-Channel Output Power 30 W per channel
Subwoofer Output Power Greater than 60 W at 10% THD+N
Supply Voltage Range 0 V to 34 V
Input Signal Type PWM
Minimum Load Impedance 3 ohm
Total Harmonic Distortion Plus Noise 0.07%
동작 온도 범위 0 C to +70 C
패키지 44-pin HTSSOP (DDV)
Package Width 6.20 mm
실장 유형 Surface Mount
Packaging Tube

TAS5186ADDV 6.20 mm 핀 구성 가이드

TAS5186ADDV(6.20 mm 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

TAS5186ADDV의 6.20 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: TAS5186ADDV.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

TAS5186ADDV 적합 용도: 6 애플리케이션s: 5.1-Channel Home Theater Amplifier, Powered Subwoofer Amplifier, Multichannel Active Speaker System, Consumer Audio Receiver, Digital Audio Speaker Amplifier, Powered Soundbar.

🎧

5.1-Channel Home Theater Amplifier

The TAS5186ADDV fits a 5.1-channel home-theater power stage because it combines six Class-D outputs with a 210-W family rating and a 0-V to 34-V supply range. The six channels can drive the five main speakers and a subwoofer from a digital audio modulator. Its stated capability above 60 W at 10% THD+N for a single-ended subwoofer supports compact but high-fidelity receiver designs. The implementation must include the manufacturer’s recommended power-ground, exposed-pad, and decoupling layout, while continuous multi-channel output requires thermal validation in the finished enclosure.

🔊

Powered Subwoofer Amplifier

The TAS5186ADDV can serve as a high-output powered-subwoofer stage when its six channels are assigned to the required speaker configuration. The device is characterized for single-ended subwoofer output above 60 W at 10% THD+N and specifies a 3-ohm minimum load. The PWM interface allows a compatible digital modulator to preserve channel synchronization and reduce analog signal-chain complexity. Designers should select the amplifier configuration and thermal solution for the lowest speaker impedance, then verify output-device and speaker protection against sustained bass demand.

🔉

Multichannel Active Speaker System

The TAS5186ADDV is appropriate for an active multichannel speaker system requiring several synchronized Class-D outputs from one audio power IC. Six integrated channels simplify the repeated use of separate amplifier packages, while the 210-W family rating provides ample system-level headroom for carefully designed speaker loads. The 44-pin HTSSOP package supports compact surface-mount assemblies but requires deliberate exposed-pad copper and power-ground routing. System integrators should match each PWM channel to the intended loudspeaker, use the stated 3-ohm load limit, and qualify sustained-output temperature rise.

📺

Consumer Audio Receiver

The TAS5186ADDV can provide the power-amplifier section of a compact consumer audio receiver where five surround channels and a subwoofer channel must be driven from a digital source. Its PWM architecture separates source conversion from power amplification, supporting a straightforward system partition around the TAS5086 modulator. The stated 0.07% THD+N supports high-fidelity playback, while the 0°C to 70°C operating range suits indoor commercial environments. Implementation should preserve channel mapping, observe the 0-V to 34-V supply range, and use the manufacturer’s reference layout to minimize switching noise.

🖥️

Digital Audio Speaker Amplifier

The TAS5186ADDV suits digital speaker-amplifier platforms that distribute PWM audio channels from a central processor to powered speaker outputs. Using the device as a dedicated power stage keeps switching amplification separate from source decoding and allows multiple channels to share a synchronized digital modulator. Its six-channel organization supports 5.1-channel or multi-zone arrangements, and its 210-W family rating allows meaningful speaker power in compact enclosures. The design team must still account for channel routing, amplifier mute behavior, thermal conditions, and the manufacturer-defined power-up requirements.

🔊

Powered Soundbar

The TAS5186ADDV can implement multiple amplification channels in a powered soundbar or compact active loudspeaker enclosure. Six outputs provide flexible channel allocation for front, surround, and low-frequency drivers without requiring six separate amplifier packages. The surface-mount HTSSOP construction supports automated assembly and board-space savings, while the stated 0.07% THD+N suits consumer playback. Because all channels share the package and local power infrastructure, the PCB should provide robust exposed-pad cooling, low-impedance power distribution, and short output paths to the speaker connectors.

추천 제품 요약

TAS5086 Digital audio modulator identified for TAS5186A chipset designs 사용처: 5.1-Channel Home Theater Amplifier, Powered Subwoofer Amplifier, Multichannel Active Speaker System, Consumer Audio Receiver, Digital Audio Speaker Amplifier, Powered Soundbar PCM1792ADBR Texas Instruments 사용처: 5.1-Channel Home Theater Amplifier, Digital Audio Speaker Amplifier PCM3060PWR Texas Instruments 사용처: Powered Subwoofer Amplifier PCM1782DBQR Texas Instruments 사용처: Multichannel Active Speaker System PCM1681PWPR Texas Instruments 사용처: Consumer Audio Receiver PCM3010DBR Texas Instruments 사용처: Powered Soundbar
What is the TAS5186ADDV?
The TAS5186ADDV is a Texas Instruments six-channel Class-D digital audio power stage rated for 210 W total output power. According to the manufacturer product page, it accepts PWM input, operates from a 0-V to 34-V supply, and is intended for 5.1-channel audio systems. It is packaged in a 44-pin HTSSOP with the DDV package designation.
How many channels and watts does the TAS5186ADDV provide?
The TAS5186ADDV provides six Class-D output channels in a 210-W device family. Texas Instruments lists the exact ordering code as a 6-channel amplifier with a nominal 30-W output rating and describes capability above 60 W for a single-ended subwoofer at 10% THD+N. The 210-W figure represents the family’s stated total power capability rather than 210 W on every individual channel.
What supply voltage does the TAS5186ADDV use?
The TAS5186ADDV operates from a 0-V to 34-V supply range. Texas Instruments identifies it as a PWM-input Class-D amplifier for 5.1-channel systems. Because the power stage can dissipate substantial heat at high output power, the design should maintain the recommended supply decoupling and provide adequate copper area under the exposed thermal pad.
Where can I download the TAS5186ADDV datasheet?
The official TAS5186A product page provides the manufacturer datasheet and ordering information for TAS5186ADDV. It identifies the component as a 210-W, 5.1-channel, PWM-input Class-D amplifier in a 44-pin HTSSOP (DDV) package. Use the manufacturer document for the complete pin descriptions, thermal information, application circuit, and recommended PCB layout.
Where is the TAS5186ADDV pinout?
The TAS5186ADDV pinout is published in the pin-configuration section of the Texas Instruments TAS5186A manufacturer datasheet. The exact TAS5186ADDV ordering code uses the 44-pin DDV package. Assign PCB tracks from that pin-description table, including the exposed thermal pad and power-ground requirements, because package families with similar names may use different exposed-pad arrangements.
Can the TAS5186ADDV replace another TAS5186A ordering code?
The TAS5186ADDVR and TAS5186ADDVG4 are direct ordering-code variants associated with the same TAS5186A device, while TAS5186DDVG4 is another documented family ordering code. Compatibility still depends on the package suffix, mounting form, and qualification requirements. Confirm the manufacturer ordering table before replacing an installed part because suffix changes can affect packing or qualification.
TAS5186ADDV vs TAS5186DDVG4: which is better for a 5.1-channel amplifier?
Both ordering codes belong to the TAS5186A six-channel Class-D power-stage family, so the core channel count and 210-W family rating align. The available information does not establish a meaningful electrical-performance difference between TAS5186ADDV and TAS5186DDVG4. Select the ordering code that matches the required qualification, packing method, and lifecycle conditions for the production design.
When should I choose TAS5186ADDV over another TAS5186A ordering code?
Choose TAS5186ADDV when the production design requires the exact 44-pin DDV ordering code, stated 0°C to 70°C range, and tube-packaged configuration. It is appropriate for a multichannel design whose six PWM-driven outputs must operate from a 0-V to 34-V supply. Select another documented suffix only when qualification, packing, or lifecycle requirements justify the change.
Is the TAS5186ADDV suitable for a home-theater power amplifier?
The TAS5186ADDV is suitable for a 5.1-channel home-theater power amplifier because it provides six Class-D outputs, a 210-W family rating, PWM input, and a stated 60-W subwoofer capability above 60 W at 10% THD+N. A compatible modulator and carefully designed thermal, power, and grounding layout are still required to realize those performance levels.
What modulator works with the TAS5186ADDV?
Texas Instruments identifies the TAS5086 as an example modulator for building a low-cost, high-fidelity system around the TAS5186A power stage. The TAS5086 performs digital audio modulation before the TAS5186ADDV drives the speaker outputs. Verify channel mapping, PWM timing, data-rate, and power sequencing against the manufacturer interface requirements before finalizing the signal chain.
What are the key specifications of TAS5186ADDV that engineers should know?
The essential TAS5186ADDV specifications are six Class-D channels, 210 W total family power, 0-V to 34-V supply operation, PWM input, 3-ohm minimum load, 0.07% THD+N, and a 0°C to 70°C operating range. The exact device uses a 44-pin HTSSOP (DDV) package. These figures define its role as a multichannel audio power stage rather than a signal-processing DAC.
How should the TAS5186ADDV be thermally managed?
The TAS5186ADDV requires a PCB that can remove heat from its exposed pad and power stages. Route exposed-pad and power-ground connections according to the manufacturer datasheet, preserve uninterrupted copper where practical, and avoid long high-current return paths between the amplifier and speaker wiring. Validate the enclosure and ambient-temperature limit with sustained multichannel playback.
Where can I buy TAS5186ADDV and what is its lead time?
Use the Request a Quote form on this page to request TAS5186ADDV pricing, current inventory, minimum order quantity, and lead time. The device is listed as a 44-pin HTSSOP audio amplifier in a tube package. Commercial terms can change with availability and order volume, so obtain a current quotation for the exact ordering code before committing to the production schedule.
Is TAS5186ADDV in stock?
Current TAS5186ADDV stock should be confirmed through the Request a Quote form on this page. Market availability can vary by package, order quantity, and production schedule. The manufacturer ordering page identifies TAS5186ADDV as part of the TAS5186A family, but a live quotation is the appropriate method for checking allocatable inventory and delivery timing.
What can replace the TAS5186ADDV?
The documented direct alternatives are the TAS5186 family ordering codes listed on this page, including TAS5186ADDVR, TAS5186ADDVG4, and TAS5186DDVG4. They use the same 44-pin DDV class of package, but suffix, packing, and qualification details must be checked before substitution. No distinct cross-brand pin-compatible replacement was confirmed.
Is TAS5186ADDV RoHS compliant?
RoHS status cannot be confirmed from the available product summaries and should be checked against the manufacturer material-declaration or product-compliance documentation for the exact ordering code. The same applies to REACH, lead-free, halogen-free, and conflict-minerals status. Use the Request a Quote form to request current compliance documentation and the exact package configuration required for procurement.

엔지니어링 참조 데이터: TAS5186ADDV — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the TAS5186ADDV for a 5.1-channel or six-output Class-D design requiring the exact Texas Instruments DDV ordering code, a 210-W family rating, PWM input, and a 0-V to 34-V supply. TAS5186ADDVR and TAS5186ADDVG4 are directly documented family ordering codes with the same package and core ratings; choose them when their packing or qualification suffix better matches production requirements. TAS5186DDVG4 offers the same family architecture but should be selected only after confirming its exact ordering details and qualification status. No distinct cross-brand drop-in replacement was confirmed. Regardless of suffix, verify the 3-ohm load limit, output-power interpretation, exposed-pad layout, thermal behavior, and modulator compatibility before releasing the PCB.

대체품과의 비교

파라미터 이 제품 TAS5186ADDVR TAS5186ADDVG4 TAS5186DDVG4
Package HTSSOP-44 (DDV) HTSSOP-44 (DDV) HTSSOP-44 (DDV) HTSSOP-44 (DDV)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Output Channels 6 channels 6 channels 6 channels 6 channels
Total Output Power 210 W 210 W 210 W 210 W
Supply Voltage Range 0 V to 34 V 0 V to 34 V 0 V to 34 V 0 V to 34 V
Input Type PWM PWM PWM PWM
Minimum Load Impedance 3 ohm 3 ohm 3 ohm 3 ohm
Total Harmonic Distortion Plus Noise 0.07% 0.07% 0.07% 0.07%

주요 차별점

  • Six integrated Class-D channels in one power-stage package (vs TAS5186DDVG4)
  • Wide 0-V to 34-V supply operating range (vs TAS5186ADDVR)
  • Specified 0.07% THD+N performance (vs TAS5186ADDVG4)

설계 노트

Treat the exposed pad as the principal heat-spreading path rather than as an optional electrical connection. Follow the manufacturer land pattern and preserve uninterrupted ground copper beneath the HTSSOP-44 package. Validate the design with the highest sustained multichannel output, speaker impedance, ambient temperature, and enclosure conditions because the 210-W family rating does not establish safe continuous dissipation for every channel combination.

Use the manufacturer datasheet for the complete power, ground, PWM input, and exposed-pad network. Place high-frequency decoupling close to the relevant supply pins and keep switching-current loops compact. Speaker outputs are high-energy nodes, so route them away from sensitive audio inputs and keep the power-ground return path short and wide to reduce voltage drops and radiated switching noise.

Do not assume that the 210-W family rating means every one of the six outputs can deliver 210 W continuously. The exact ordering information lists 30 W output power, a 3-ohm minimum load, and operation from 0 V to 34 V. Verify modulation compatibility, speaker impedance, protection behavior, and thermal limits for the intended configuration before layout release.

Plan the digital audio subsystem to keep PWM timing and channel mapping consistent across all six outputs. Decouple the modulator and power stage according to their individual datasheets, observe any manufacturer-specified power-up behavior, and keep test points accessible for debugging. Separate low-level audio references from output-current paths to avoid common-impedance coupling and channel-to-channel imbalance.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

Compliance declarations were not included in the available product summaries. Request current material and quality documentation for the exact ordering code before production approval.

데이터 검증일: 2026-11-20 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

TAS5186ADDV datasheet TAS5186ADDV pinout TAS5186ADDV datasheet pdf TAS5186ADDV specifications TAS5186ADDV equivalent TAS5186ADDV replacement TAS5186ADDV vs TAS5186DDVG4 Texas Instruments TAS5186ADDV TAS5186ADDV 44 pin HTSSOP TAS5186ADDV 210W Class-D amplifier TAS5186ADDV home theater amplifier TAS5186ADDV PWM input TAS5186ADDV price TAS5186ADDV stock TAS5186ADDV application circuit

관련 부품 & 용어

Texas Instruments TAS5186ADDV TAS5186A TAS5186ADDVR TAS5186ADDVG4 TAS5186DDVG4 TAS5086 Class-D amplifier digital power stage PWM input audio amplifier multichannel amplifier 5.1-channel audio powered subwoofer HTSSOP-44 DDV package surface mount THD+N output power load impedance exposed thermal pad home theater digital audio modulator speaker amplifier
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기