TAS5615PHD - 300W Mono Class-D Power Stage | Texas Instruments
부품 번호: TAS5615PHD ✓ 활성TAS5615PHD 개요
A Class-D audio power amplifier is a switching amplifier that uses pulse-width modulation to deliver speaker power efficiently. The TAS5615PHD belongs to the Class-D amplifier, audio power IC, and power-management semiconductor hierarchy. Unlike a conventional linear Class-AB output stage, its switching architecture concentrates unwanted energy at high frequencies, reducing output-stage heat while retaining low audio distortion through the integrated closed-loop feedback system.
The headline features include analog input, support for a 50 V power-stage supply, up to 160 W per channel in stereo operation, and up to 300 W in mono operation. PurePath HD feedback is intended to suppress distortion associated with output-network component variation. The device accepts conventional analog audio signals, which simplifies its use in systems that do not require a PWM audio source. Its 64-pin HTQFP package provides numerous power, feedback, ground, signal, and control connections needed for a high-power output stage.
The PurePath HD architecture continuously corrects the output waveform using feedback sensed from the speaker output. This approach is intended to provide Class-AB-like fidelity while retaining the efficiency of a Class-D output stage. Texas Instruments specifies distortion below 0.03%, making the device suitable for high-fidelity amplification where audible distortion, clipping, or thermal losses would otherwise constrain the amplifier selection.
Typical uses include powered speakers, home-theater amplifiers, professional audio equipment, soundbars, multichannel audio systems, and compact high-power subwoofer or surround-speaker platforms. In a stereo design, the integrated output stages drive left and right channels. In a mono design, the power capability can be consolidated for a single loudspeaker or bridged audio architecture, subject to the thermal and load limitations in the manufacturer datasheet.
Careful thermal design is essential because the exposed pad must dissipate power generated by the switching output stage. Follow the manufacturer application diagrams for the power-supply topology, output inductors, feedback network, input filtering, copper area, and thermal layout. The 50 V power-stage rail should have low output impedance and low noise, and the 12 V supply should originate from a low-noise, low-output-impedance regulator.
This page organizes the verified power ratings, package information, operating architecture, application fit, and engineering cautions for the TAS5615PHD. It also distinguishes the target device from related TI products so design engineers can determine whether the analog-input interface, power rating, package, and thermal requirements match the intended amplifier platform.
드롭인 대체품: TAS5615PHD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TAS5615PHD (동일 폼 팩터 및 풋프린트) — 차이점: Feedback Architecture, Maximum Stereo Output Power, Package, Total Harmonic Distortion.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청TAS5615PHD 최대 정격 & 전기적 특성
| Amplifier Type | Class-D audio power amplifier |
| Input Architecture | Analog input |
| Feedback Architecture | Integrated PurePath HD closed-loop feedback |
| Maximum Stereo Output Power | 160 W |
| Maximum Mono Output Power | 300 W |
| Speaker Load | 8 ohm |
| Power-Stage Supply | 50 V |
| Total Harmonic Distortion | <0.03% |
| Supported Output Configuration | 1-channel mono, 2-channel stereo, or 4-channel stereo |
| 패키지 | 64-pin HTQFP with exposed pad, 14 mm x 14 mm |
| 실장 유형 | Surface mount |
| Evaluation Module | TAS5615PHD2EVM |
| Recommended 12 V Supply Type | Low-noise, low-output-impedance voltage regulator |
| Power-Stage Rail Requirement | Low output impedance and low noise |
TAS5615PHD 64-pin htqfp with exposed pad, 14 mm x 14 mm 핀 구성 가이드
TAS5615PHD(64-pin htqfp with exposed pad, 14 mm x 14 mm 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TAS5615PHD.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TAS5615PHD 적합 용도: 6 애플리케이션s: Powered Stereo Speaker, High-Power Subwoofer Amplifier, Home-Theater Power Amplifier, Professional Audio Power Stage, Multichannel Speaker Amplifier, Soundbar Speaker Amplifier.
Powered Stereo Speaker
The TAS5615PHD fits a high-output powered-speaker platform requiring analog input and Class-D efficiency. According to the Texas Instruments product page, the device can deliver up to 160 W stereo into 8-ohm speakers from a single 50 V supply, while PurePath HD feedback helps maintain distortion below 0.03% under specified conditions. The amplifier is used in the power stage after the preamplifier and volume-control network. Designers must follow the manufacturer output-filter and feedback circuits, provide a low-impedance 50 V rail, and allocate sufficient exposed-pad copper and airflow for continuous operation.
추천
High-Power Subwoofer Amplifier
The TAS5615PHD is suitable for a mono subwoofer amplifier that can use the device's stated 300 W mono capability. Its Class-D switching architecture improves amplifier efficiency compared with a linear output stage, while the integrated PurePath HD feedback network targets low audio distortion without requiring the external feedback network used by some other power stages. The implementation must use the manufacturer-specified output inductors, filter components, and feedback connections. Continuous 300 W operation also requires careful validation of speaker impedance, supply capability, PCB thermal performance, and the exposed-pad heat-spreading area.
추천
Home-Theater Power Amplifier
For home-theater amplification, the TAS5615PHD can support the analog-input power stages used to drive passive loudspeaker channels. Its available output configurations include mono, stereo, and four-channel use, and the 160 W stereo capability into 8-ohm speakers is suitable for higher-power playback equipment. The analog interface accepts conventional preamp outputs, while PurePath HD feedback provides a mechanism for low-distortion Class-D operation. Channel population, rail loading, and thermal design must be coordinated so that simultaneous operation does not exceed the package and board heat-dissipation limits.
추천
Professional Audio Power Stage
The TAS5615PHD can serve as the high-power output stage in professional audio equipment requiring analog input and efficient amplification. Its Class-D architecture reduces output-stage dissipation relative to a comparable linear amplifier, while PurePath HD feedback is designed to maintain signal fidelity below 0.03% THD under the manufacturer's specified test conditions. Professional systems also demand stable low-impedance drive and consistent thermal behavior, so the power rail, output filter, feedback routing, and exposed-pad cooling must follow the Texas Instruments application diagrams. Final qualification should include load sweeps, thermal testing, and channel-to-channel verification.
추천
Multichannel Speaker Amplifier
The TAS5615PHD supports four-channel speaker configurations for compact multichannel amplification systems. This makes it relevant to home cinema, distributed audio, and powered-speaker products that need several Class-D outputs while retaining analog-input compatibility. The device's closed-loop PurePath HD architecture provides feedback-based output regulation, and the manufacturer identifies 160 W stereo output into 8-ohm speakers from a 50 V supply. Designers must confirm the precise channel mode, maintain the recommended supply and output networks, and balance amplifier loading across the enclosure. Shared thermal capacity is often the decisive constraint in a four-channel implementation.
추천
Soundbar Speaker Amplifier
The TAS5615PHD is applicable to a soundbar or compact active-speaker design that accepts analog signals and needs substantial output power in a small heatsink footprint. Class-D operation improves efficiency, while PurePath HD feedback allows a high-power output stage without relying on a conventional linear Class-AB transistor arrangement. The target application should use the manufacturer's application circuit to preserve the intended feedback and filtering behavior. Soundbar packaging makes thermal design especially important because several channels may operate simultaneously in a confined enclosure, so exposed-pad via density, copper area, and ambient-temperature derating require careful evaluation.
추천
추천 제품 요약
엔지니어링 참조 데이터: TAS5615PHD — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Brand | Texas Instruments |
| Package | 64-pin HTQFP with exposed pad, 14 mm x 14 mm |
| Amplifier Type | Class-D |
| Input Architecture | Analog input |
| Feedback Architecture | Integrated PurePath HD closed-loop feedback |
| Maximum Stereo Output Power | 160 W into 8 ohms |
| Maximum Mono Output Power | 300 W |
| Power-Stage Supply | 50 V |
| Total Harmonic Distortion | <0.03% |
| Output Configurations | 1-channel mono, 2-channel stereo, or 4-channel stereo |
설계 노트
Treat the exposed pad as the primary thermal path for the Class-D output stage. Connect it to the PCB ground or power-ground plane with the thermal-via arrangement recommended in the manufacturer application diagrams, and provide as much uninterrupted copper as the enclosure allows. Validate the final assembly at the maximum intended output power, highest ambient temperature, and worst-case speaker impedance. A nominal 300 W device rating does not guarantee that an undersized board, restricted airflow, or shared multichannel loading will maintain safe junction temperatures.
The Texas Instruments datasheet states that the 12 V supply should use a low-noise, low-output-impedance voltage regulator and that the 50 V power-stage supply should also have low output impedance and low noise. Follow the recommended bulk and local decoupling network and preserve the specified supply sequencing and grounding arrangement. High output power can produce rapid current transitions in the speaker and supply loops, so validate supply stability, droop, noise coupling, and startup behavior with the intended load rather than evaluating only a no-load circuit.
Reproduce the manufacturer output-filter, feedback, and supply components and maintain short, low-impedance routing for high-current power paths. The exposed pad needs a dense and balanced via field to transfer heat into both surface and inner copper layers. Keep sensitive analog input routing away from switching-node and output-filter areas, and use the datasheet's recommended grounding topology. Because the device can operate at 160 W stereo or 300 W mono, conductor width, vias, connectors, and copper connections must carry the intended current without unacceptable voltage drop or heating.
Do not substitute a PWM-input power stage for the analog-input TAS5615PHD without redesigning and revalidating the signal path and pin functions. Also avoid changing output inductors, feedback components, or filter values outside the manufacturer circuit without stability and distortion analysis. Check the required output-filter topology, speaker impedance, continuous-power limits, and thermal derating. The PurePath HD label alone does not make unrelated Class-D amplifiers interchangeable, because external component values and feedback implementation determine practical performance.
규정 준수 정보
Compliance and qualification status are not stated in the accessible manufacturer information. Obtain current declarations for the exact ordering code before production release.