TJA1043ATK/0Y - High-Speed CAN Transceiver | NXP | 14-HVSON
부품 번호: TJA1043ATK/0Y ✓ 활성TJA1043ATK/0Y 개요
A CAN transceiver is the physical-layer interface between a CAN controller and the differential CAN bus. It converts logic-level transmit and receive signals into a robust differential bus waveform and provides the receive data back to the controller. As a single-transceiver device, the TJA1043ATK/0Y integrates a CAN transmitter, CAN receiver, bus biasing functions, and interface protection in one compact package.
The principal differentiators of the TJA1043 family are its fail-safe and diagnostic capabilities together with advanced power-management functions. Fail-safe behavior is important in automotive networks because it helps define the transceiver state when the bus supply or bus line is absent. Diagnostic features support system-level fault detection by exposing bus-related conditions to the host electronics. These functions are more relevant than raw data-rate differences when the transceiver is selected for a new vehicle or industrial CAN network.
The 14-HVSON package is intended for compact surface-mount assemblies. Its small 3 x 4.5 mm footprint supports high-density controller-unit and gateway layouts, although exposed-pad layout and thermal performance must follow the package recommendations in the manufacturer datasheet. Because the package is lead-free and very small, careful PCB footprint design, solderability verification, and assembly process control are essential.
Typical uses include automotive electronic control units, body-comfort modules, powertrain controllers, industrial automation equipment, and CAN-based sensors. In these systems, the TJA1043ATK/0Y sits between the CAN controller and the bus connector, while external bus protection, decoupling, and common-mode choke elements are selected according to the network topology and electromagnetic-compatibility requirements.
This page organizes the confirmed package and product information, provides practical application guidance, and separates documented TJA1043 characteristics from parameters that must be confirmed in the manufacturer datasheet. The datasheet remains the controlling document for pin assignments, electrical limits, timing values, recommended application circuits, and qualification information.
드롭인 대체품: TJA1043ATK/0Y — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TJA1043ATK/0Y (동일 폼 팩터 및 풋프린트) — 차이점: Package, Transceiver Configuration.
TJA1059TK/3/1J
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TJA1051TK/3/1J
✅ 드롭인가격 문의
데이터시트 보기 →TJA1043ATK/0Y 사양
| Product Type | High-speed CAN transceiver |
| Transceiver Configuration | 1 transmit / 1 receive (1/1) |
| Bus Type | Controller Area Network (CAN) |
| 패키지 | 14-HVSON (3 x 4.5 mm) |
| 실장 유형 | Surface mount |
| 핀 수 | 14 pins |
| Fail-Safe Features | Supported |
| Diagnostic Features | Supported |
| Power Management | Advanced power-management features |
TJA1043ATK/0Y 14-hvson (3 x 4.5 mm) 핀 구성 가이드
TJA1043ATK/0Y(14-hvson (3 x 4.5 mm) 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: TJA1043ATK/0Y.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TJA1043ATK/0Y 적합 용도: 6 애플리케이션s: Automotive Electronic Control Units, Body Comfort and Vehicle Gateway Modules, Industrial CAN Automation Controllers, CAN-Based Sensor and Measurement Hubs, Industrial Communication Gateways, Robotics and Mobile Platform Communication.
Automotive Electronic Control Units
The TJA1043ATK/0Y fits an automotive electronic control unit that connects a CAN controller to a physical CAN bus. Its documented fail-safe behavior, diagnostic features, and advanced power management support systems where a compact 14-HVSON 3 x 4.5 mm package saves board area. Place the transceiver beside the controller and route the differential bus pair as a short, impedance-controlled pair toward the connector or protection network. Confirm the family-specific transient, temperature, and bus-fault requirements in the manufacturer datasheet before production release.
추천
Body Comfort and Vehicle Gateway Modules
A body-comfort module or vehicle gateway can use the TJA1043ATK/0Y as the single CAN physical-layer interface. The 1/1 configuration provides one transmit and one receive path without duplicating a transceiver for each channel, and the 3 x 4.5 mm HVSON body supports dense controller-unit layouts. Diagnostic functions are especially useful when the host controller must identify bus faults, while fail-safe operation defines behavior during abnormal supply or bus conditions. Final circuit completion still requires the recommended bus protection and termination components from the NXP application guidance.
추천
Industrial CAN Automation Controllers
The TJA1043ATK/0Y is appropriate for compact industrial automation controllers that exchange data over a high-speed CAN network. Its small 14-HVSON 3 x 4.5 mm package leaves more PCB area for isolation, power conversion, and I/O, while fail-safe and diagnostic functions improve serviceability. In a machine controller, keep the CANH and CANL traces short, symmetrical, and separated from noisy switching nodes. Confirm the transceiver's operating voltage and environmental limits against the industrial equipment specification before using it outside a protected enclosure.
추천
CAN-Based Sensor and Measurement Hubs
A CAN-connected sensor hub can use the TJA1043ATK/0Y to bridge a microcontroller and a shared measurement bus. The single CAN channel supports a network topology in which each node has one physical transceiver, and diagnostics help isolate wiring or termination problems during maintenance. Because the package is compact, place it near the bus connector while routing the differential pair away from analog sensor inputs. Use the manufacturer datasheet for bypass-capacitor placement, bus-termination requirements, and any required common-mode choke implementation.
추천
Industrial Communication Gateways
The TJA1043ATK/0Y can serve as the CAN-side interface in an industrial communication gateway that translates between CAN and another network or control bus. Its compact 14-HVSON package is useful where several isolated communication channels compete for board area, and the documented diagnostic functions support fault monitoring in unattended equipment. Route the CAN bus toward the protected connector through the application-recommended protection network, maintain symmetry between CANH and CANL, and verify chassis-grounding strategy for the installation environment.
추천
Robotics and Mobile Platform Communication
A robot controller or mobile platform can use the TJA1043ATK/0Y to connect a motion or navigation controller to a CAN-based subsystem. The documented fail-safe behavior is valuable when wiring faults or supply disturbances occur in a mobile installation, and diagnostics simplify fault isolation. Keep the 3 x 4.5 mm transceiver near the connector entry, provide the recommended decoupling locally, and maintain a controlled differential impedance on CANH and CANL. Validate radiated and conducted emissions in the complete platform because the enclosure and cable harness materially affect CAN-bus EMC performance.
추천
추천 제품 요약
엔지니어링 참조 데이터: TJA1043ATK/0Y — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
설계 노트
Create the PCB footprint from the 14-HVSON package drawing in the NXP manufacturer datasheet rather than adapting an SOIC-14 or generic QFN-14 land pattern. Confirm the 3 x 4.5 mm body dimensions, pin-1 orientation, pad lengths, exposed-pad connection, solder-mask clearance, and paste stencil. A small package does not remove the need for exact land-pattern verification.
Route CANH and CANL as a short, symmetrical differential pair with continuous return-path geometry, and keep the pair away from switching nodes, crystal circuitry, and high-current power loops. Place the transceiver and its recommended bypassing close to the controller or bus-entry point. The exact trace impedance, spacing, and protection-network arrangement should follow the NXP application guidance for the target bus speed.
Do not treat a similarly named TJA1043 ordering code, TJA1051, or TJA1059 as a substitute without comparing the package footprint and pin descriptions. The TJA1043ATK/0Y is a 14-HVSON 3 x 4.5 mm device, while other CAN transceiver families can use different lead counts, pin functions, electrical limits, and diagnostic interfaces. Review the exact ordering code, temperature grade, and datasheet before approving a replacement.
규정 준수 정보
The verified product information confirms the TJA1043 family application and package but does not state specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for this order code. Confirm these requirements from the manufacturer product page or the relevant compliance documents before procurement.