TLV2470ID - 6V, 2.8MHz RRIO Op Amp | Texas Instruments
부품 번호: TLV2470ID ✓ 활성TLV2470ID 개요
A rail-to-rail input/output operational amplifier is designed to accept input voltages near either supply rail and to produce output voltages close to the positive or negative rail. This is useful in battery-powered and low-voltage systems where usable signal range is limited by the supply voltage. The TLV2470ID combines that input and output range with a shutdown function, allowing a system designer to reduce supply consumption when the amplifier is not needed.
The principal performance features include a 2.8 MHz gain-bandwidth product, 600 µA/channel supply current, and a CMOS input stage with a 2.5 pA bias current. Its high-drive capability supports applications where the amplifier must drive a relatively demanding capacitive or resistive load. Rail-to-rail operation also reduces the need for separate input and output range calculations when signals can approach either supply rail.
The TLV2470ID belongs to the TLV247x family of single and dual rail-to-rail operational amplifiers. According to the Texas Instruments TLV2470 family description, the family combines low power consumption with comparatively high AC performance for its operating class. The single amplifier in the 8-pin SOIC is suitable for general-purpose precision signal conditioning when a design needs one amplifier rather than a dual package.
Typical applications include portable sensor interfaces, low-voltage filter stages, audio input conditioning, battery-powered instrumentation, and general analog signal amplification. The shutdown pin is particularly useful in portable equipment because it can disable the amplifier when the system is inactive. Rail-to-rail inputs help preserve signal fidelity when sensor outputs approach the supply rails.
Designers should verify the required output-current capability, capacitive-load stability, input common-mode range, and operating temperature range for the selected ordering code. Place bypass capacitance close to the supply pins and keep feedback routing short because high-speed amplifiers can amplify trace resistance and parasitic capacitance into stability problems.
This page combines the TLV2470ID's core technical characteristics with package guidance, sourcing answers, application analysis, and same-family replacement considerations. It also identifies where a direct substitute requires verification of pinout, electrical limits, temperature grade, and shutdown behavior before PCB reuse.
드롭인 대체품: TLV2470ID — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TLV2470ID (동일 폼 팩터 및 풋프린트).
TLV2470AID
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TLV2470AIP
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
TLV2470ID 최대 정격 & 전기적 특성
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Supply Current per Channel | 600 µA/channel |
| Input Bias Current | 2.5 pA |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Shutdown Control | Yes |
| High-Drive Capability | 600 mA/channel family description |
| 패키지 | 8-pin SOIC |
| 실장 유형 | Surface mount |
TLV2470ID 8-pin soic 핀 구성 가이드
TLV2470ID(8-pin soic 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TLV2470ID.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TLV2470ID 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Interface, Low-Voltage Audio Input Conditioning, Portable Medical Sensor Signal Conditioning, Industrial Control Signal Amplification, Low-Power Active Filter, IoT Node Analog Interface.
Battery-Powered Sensor Interface
The TLV2470ID fits low-voltage sensor front ends that need rail-to-rail input and output operation with low amplifier bias current. Its 2.5 pA CMOS input bias minimizes disturbance to high-impedance sensors, while rail-to-rail input capability helps preserve signals near the supply rails. The 600 µA/channel operating current also limits amplifier-related consumption in portable equipment. Place the device close to the sensor connector and bypass the supply pins locally; verify that input capacitance, source impedance, and the required noise gain do not compromise stability.
추천
Low-Voltage Audio Input Conditioning
The TLV2470ID can amplify audio or microphone signals in a compact, low-voltage design because its input and output stages operate rail to rail. The 2.8 MHz gain-bandwidth product provides more bandwidth than the audio band requires, while the 600 µA/channel supply current supports power-conscious portable equipment. The shutdown function can disable the amplifier when the audio path is inactive. Confirm output-current capability into the next stage and check capacitive-load stability before adding headphone, microphone, or line-level loads.
추천
Portable Medical Sensor Signal Conditioning
The TLV2470ID is applicable to low-level signal conditioning in portable medical equipment when its input bias, bandwidth, and supply-current characteristics meet the sensing chain requirements. The 2.5 pA bias current is favorable for high-impedance sources, and the 2.8 MHz gain-bandwidth product supports moderate-bandwidth conditioning stages. A shutdown-controlled amplifier can reduce consumption during inactive measurement intervals. Medical use still requires validation of patient protection, leakage, diagnostic accuracy, and applicable regulatory requirements at the complete-system level.
추천
Industrial Control Signal Amplification
The TLV2470ID is useful for amplifying control and instrumentation signals in a 6 V-class industrial system because its rail-to-rail inputs and outputs reduce the usable input and output range restrictions. The 2.8 MHz gain-bandwidth product supports general analog signal conditioning, while the shutdown input permits controlled deactivation of nonessential channels. Validate the exact operating-temperature grade for the installation environment, isolate noisy switching nodes, and use a stable reference design when the amplifier drives cables or substantial capacitive loads.
추천
Low-Power Active Filter
The TLV2470ID can serve as the active element in a low-voltage filter when the required closed-loop bandwidth stays below the device's 2.8 MHz gain-bandwidth product. Its 600 µA/channel supply current is suitable for compact battery-powered instrumentation, and rail-to-rail operation can extend signal swing in low-voltage filter stages. Select resistor values for the intended noise gain, place feedback components close to the device, and check stability because high-Q filters and long PCB traces can create excessive phase shift.
추천
IoT Node Analog Interface
The TLV2470ID fits an IoT node that conditions a sensor output before conversion or digital sampling. The 2.8 MHz bandwidth handles many sensor signals, the 2.5 pA input bias reduces loading on high-impedance sources, and the 600 µA/channel supply current supports constrained power budgets. The shutdown function allows the analog path to remain disabled during inactive intervals. Keep the amplifier and its bypass capacitor near the sensor interface, maintain a short ground path, and account for ADC settling requirements in the overall acquisition chain.
추천
엔지니어링 참조 데이터: TLV2470ID — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TLV2470AID | TLV2470AIP | TLV2470IP |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Supply Current per Channel | 600 µA/channel | 600 µA/channel | 600 µA/channel | 600 µA/channel |
| Rail-to-Rail Input | Yes | Yes | Yes | Yes |
| Rail-to-Rail Output | Yes | Yes | Yes | Yes |
| Shutdown Function | Yes | Yes | Yes | Yes |
주요 차별점
- Combines shutdown control with low supply current and moderate bandwidth (vs TLV2470AID)
- Rail-to-rail operation supports use of nearly the full low-voltage signal range (vs TLV2470IP)
- Single-amplifier configuration reduces package size for one-channel designs (vs TLV2470AIP)
설계 노트
Place the supply bypass capacitor adjacent to the positive and negative pins, and route each supply trace directly to the device. Keep the feedback loop compact and use a continuous ground plane beneath the amplifier. Because the TLV2470ID combines a 2.8 MHz gain-bandwidth product with high-drive capability, long feedback traces and parasitic capacitance can reduce phase margin or produce unexpected oscillation.
Do not assume that rail-to-rail input and output means the amplifier can swing exactly to the rails. Consult the manufacturer datasheet for output-swing and common-mode limits at the intended supply voltage and load. Also account for the voltage drop across the shutdown-control connection. Undefined shutdown voltage or excessive input voltage can move the device outside its specified operating conditions.
Estimated: at a 5 V supply, a 1 kΩ load, and an output of 2.5 V, the output stage would dissipate approximately 6.25 mW, while the amplifier's stated 600 µA/channel supply current corresponds to roughly 3 mW from a 5 V rail. Actual total power depends on quiescent current, output-current direction, supply voltage, and shutdown state. Use these estimates only for an early power-budget check.
For high-impedance sources, minimize leakage around the input node and avoid contaminated board areas. The 2.5 pA input bias is favorable for source resistance, but input capacitance and resistor thermal noise may still dominate. For an active filter, select gain-bandwidth and noise-gain headroom carefully and simulate the complete loop with PCB parasitics before fabricating the board.
규정 준수 정보
Compliance attributes were not stated in the manufacturer page or other listed product information. Qualification status must be confirmed for the exact ordering code before use in regulated or automotive designs.