TS393MDT - Micropower Dual Comparator | STMicroelectronics
부품 번호: TS393MDT ✓ 활성TS393MDT 개요
A voltage comparator is an analog integrated circuit that compares an input voltage against a reference voltage and changes its output state when the relationship between them changes. The TS393MDT belongs to the comparator hierarchy within amplifier and signal-conditioning integrated circuits. Its dual-channel architecture allows two independent threshold decisions in one package, while its CMOS input stage provides very high impedance and draws minimal supply current for battery-powered and always-on equipment.
Key features include open-drain outputs, which permit wired-OR connection and operation with external pull-up resistors. The manufacturer describes the TS393 as compatible with the bipolar LM393 function while consuming approximately 20 times less current than the dual bipolar LM393. Its operating temperature range extends from -55 °C to 125 °C, making it suitable for industrial, automotive, and defense-related equipment when the complete system design and qualification requirements are satisfied.
The electrical characteristics support threshold sensing where low supply current, high input impedance, and moderate propagation speed are more important than nanosecond response. A 10^12 Ω typical input impedance minimizes loading of high-impedance sensor nodes, while the 2.5 µs typical response time allows the device to respond to slowly changing or moderate-frequency events. The open-drain architecture requires a pull-up resistor when a logic-high output is required, and careful attention should be paid to output-node capacitance, leakage, and pull-up resistor selection.
Typical applications include battery-powered monitoring circuits, industrial sensor interfaces, dual-threshold detection, window comparators, overvoltage and undervoltage supervision, and logic-level conversion between open-drain nodes. Two comparators in one package are especially useful when a compact design must monitor one signal against two limits or perform complementary decisions.
When laying out a board, place input and pull-up components close to the relevant pins, maintain a stable ground reference, and avoid long traces around high-impedance input nodes. Because the output is open drain, the effective rise time depends on the pull-up resistance and total output capacitance rather than solely on the comparator’s internal response time.
This product page combines the TS393MDT electrical characteristics, practical comparator design guidance, sourcing information, and a clearly qualified drop-in comparison with the bipolar LM393DT. It supports faster component selection by separating verified device facts from application-specific design considerations and replacement trade-offs.
드롭인 대체품: TS393MDT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TS393MDT (동일 폼 팩터 및 풋프린트) — 차이점: Number of Channels, Output Type, Package, Response Time.
LM393DT
✅ 드롭인✓ 재고 있음
$0.0461 / 개
데이터시트 보기 →TS393MDT 최대 정격 & 전기적 특성
| Comparator Type | Dual general-purpose voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Maximum | 18 V |
| Typical Supply Current per Comparator | 9 µA |
| Input Impedance | 10^12 Ω typical |
| Response Time | 2.5 µs typical |
| Maximum Input Offset Voltage | 6.5 mV |
| 출력 유형 | Open-drain |
| Technology | CMOS |
| Operating Temperature Minimum | -55 °C |
| Operating Temperature Maximum | 125 °C |
| 패키지 | 8-pin SOIC |
| 실장 유형 | Surface mount |
| RoHS 상태 | Compliant |
| Lead-Free Status | Lead free |
| Compatibility | Compatible with bipolar LM393 function |
TS393MDT 8-pin soic 핀 구성 가이드
TS393MDT(8-pin soic 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TS393MDT.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TS393MDT 적합 용도: 6 애플리케이션s: Battery-Powered Threshold Monitoring, Industrial Sensor Interface, Overvoltage and Undervoltage Supervision, Dual Window Comparator, Open-Drain Logic Interface, Automotive and Heavy-Duty Condition Monitoring.
Battery-Powered Threshold Monitoring
The TS393MDT fits battery-powered threshold detection because each CMOS comparator typically consumes only 9 µA, reducing standby demand in portable monitoring equipment. Two channels can independently compare a sensor signal with separate reference levels, allowing one compact package to provide upper- and lower-threshold decisions. The 10^12 Ω typical input impedance minimizes loading of high-impedance sensing nodes. Because the outputs are open drain, external pull-up resistors define the logic-high state and permit wired-OR operation when several detection events must share a common output node.
추천
Industrial Sensor Interface
The TS393MDT is suitable for industrial sensor interfaces where a high-impedance input stage and extended temperature operation are valuable. Its 10^12 Ω typical input impedance reduces loading on resistive dividers, probe electrodes, and other high-source-impedance sensors. The -55 °C to 125 °C operating range covers demanding environmental conditions, while the 2.5 µs typical response time is suitable for many process-control and condition-monitoring signals. An open-drain output can drive a wired-OR alarm bus or a pulled-up logic input, although a pull-up must be selected with the bus capacitance and required rise time in mind.
추천
Overvoltage and Undervoltage Supervision
The two independent TS393MDT channels can supervise one supply against an upper limit and a lower limit, eliminating the need for two separate comparator packages. Each channel provides an open-drain fault indication that can be pulled up and combined with another signal. The 9 µA typical consumption per comparator is valuable in always-on monitoring systems, while the 18 V maximum supply rating allows operation from higher-voltage rails when the individual input limits are respected. For power-supply designs, use the manufacturer’s electrical-characteristics table to confirm the allowed input and output states under every expected transient.
추천
Dual Window Comparator
The TS393MDT can implement a compact window comparator by using one channel for the lower threshold and the other for the upper threshold. A monitored signal outside the acceptable range can then produce an open-drain fault indication. The device’s 10^12 Ω typical input impedance helps preserve accuracy when the sensing divider has a high source impedance, and its 2.5 µs typical response time provides rapid enough response for many slow-moving system variables. The output rise time is set by the external pull-up and bus capacitance, so the design should verify both comparator delay and output-network timing.
추천
Open-Drain Logic Interface
The TS393MDT can serve as a robust open-drain logic interface when a system must translate a variable analog level into a pulled-up digital fault signal. Its high input impedance reduces loading, and its dual-channel construction allows complementary or independent decisions. Open-drain outputs are useful for wired-OR buses because any output may pull the shared line low while all inactive outputs remain high-impedance. The external pull-up resistor should be selected to achieve the required rise time without exceeding the device’s output-current limits, and system timing should include the 2.5 µs typical internal response time.
추천
Automotive and Heavy-Duty Condition Monitoring
The TS393MDT’s -55 °C to 125 °C operating range and dual open-drain outputs make it useful as a building block in heavy-duty condition-monitoring circuits. It can compare actuator, battery, or sensor signals and create a wired-OR diagnostic indication for a controller. The typical 9 µA consumption per comparator reduces continuous drain in always-connected systems. Automotive deployment still requires validation of the complete device qualification, electrical limits, transient immunity, and system safety requirements; the basic TS393MDT ordering code should not be treated as proof of a specific AEC-Q100 qualification.
추천
추천 제품 요약
엔지니어링 참조 데이터: TS393MDT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM393DT |
|---|---|---|
| Brand | STMicroelectronics | Texas Instruments |
| Package | SOIC-8 (8-SOIC) | SOIC-8 (8-SOIC) |
| Comparator Configuration | Dual | Dual |
| Output Type | Open drain | Open drain |
| Input Stage Technology | CMOS | Bipolar |
주요 차별점
- Lower typical comparator supply current (vs LM393DT)
- Very high input impedance for high-impedance sensing (vs LM393DT)
- Compact dual open-drain channel in an 8-pin SOIC (vs LM393DT)
- Wide specified operating-temperature range (vs LM393DT)
설계 노트
Route the two comparison inputs directly to their sensing sources and keep them away from the open-drain output and pull-up network. The TS393MDT has a 10^12 Ω typical input impedance, but high-impedance traces can still accumulate leakage and coupling. Place input and output components near their associated pins, keep the comparator ground path short, and use a continuous ground reference to minimize threshold shifts.
An open-drain output does not actively drive a logic-high voltage; it only pulls the node low or releases it. Select the external pull-up using the required logic-high level, total bus capacitance, desired rise time, and output-current limits. Also account for the 2.5 µs typical response time and the pull-up-generated rise time when defining system alarm latency.
Estimated: with both comparators operating, the typical supply consumption based on 9 µA per comparator is 18 µA, excluding output pull-up current and input bias effects. Confirm the actual supply demand across temperature and process conditions using the manufacturer electrical characteristics. A pull-up resistor continuously dissipates current whenever an output is low, so its value may dominate the total standby power of the circuit.
Use the TS393MDT for signals that can be handled by its 2.5 µs typical response time rather than requiring high-speed edge detection. If the monitored input can slew rapidly, verify total propagation delay, input overdrive, and output rise time at the intended supply voltage. Slow output edges caused by excessive pull-up resistance and bus capacitance may create timing problems even when the comparator’s internal response time is acceptable.
규정 준수 정보
The distributor product record identifies the TS393MDT as lead free and RoHS compliant. No separate REACH, AEC-Q100, halogen-free, or conflict-minerals declaration was established.