EPM570GM100C5N - 440 Macrocell MAX II CPLD, 100-MBGA | Intel
MPN: EPM570GM100C5N ✓ AktifEPM570GM100C5N Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile, flash-based programmable logic device that sits in the hierarchy between simple PLDs and full FPGAs. CPLDs are widely used for I/O expansion, bus bridging, power-up sequencing, and glue-logic functions where deterministic timing and instant-on behavior are required. The MAX II family pioneered low-cost, low-power CPLDs based on a look-up table (LUT) architecture, offering higher logic density than traditional PAL/GAL devices while keeping non-volatile instant-on capability.
Key features of the EPM570GM100C5N include 440 logic elements (macro cells), a flash-based non-volatile configuration memory that eliminates external boot PROM, in-system programmability via JTAG, MultiVolt core supporting I/O voltages from 1.5 V to 3.3 V, and an internal oscillator. The MultiVolt I/O interface allows the part to bridge between 3.3 V, 2.5 V, 1.8 V, and 1.5 V logic families without external level shifters, simplifying mixed-voltage PCB designs.
The device's flash-backed architecture provides true instant-on operation - the device is functional within microseconds of power-up. The 100-ball MBGA package supports high-density board layouts while keeping the footprint compact at 6 x 6 mm, suitable for space-constrained industrial, consumer, and communications designs.
Typical applications include I/O expansion and bus bridging in industrial controllers, power-up/power-down sequencing logic for FPGA and ASIC rails, JTAG-controlled configuration management, LED display driving and refresh, and address decoding glue logic between processors and peripherals. Designers frequently select the EPM570 family for designs that previously required multiple 74-series logic devices, since one CPLD replaces dozens of discrete gates while adding reconfigurability.
Design consideration: when migrating between speed grades (C4, C5, C5N, I5N), verify that the timing closure margins remain acceptable. The C5N industrial grade (-40C to +125C) is preferred for harsh-environment deployments, while commercial C5 is suitable for cost-sensitive consumer designs. Always observe JTAG chain integrity when the CPLD shares the JTAG bus with other programmable devices.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.
Pilihan pengganti yang segera untuk EPM570GM100C5N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera EPM570GM100C5N (sama faktor bentuk dan kaki) — berbeza dalam Operating Temperature, Package, Process Technology, Programming Interface, Configuration Memory.
EPM570GM100I5N
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →EPM570GM100C4N
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
EPM570F100C5N
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →EPM570F100I5N
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →EPM570F100C4N
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →EPM570F100A5N
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →EPM570GM100C5N Penilaian maksimum & Ciri-ciri Elektrik
| Family | MAX II |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Macro Cells | 440 |
| User I/Os | 76 |
| Logic Elements | 440 |
| Bilangan Pin | 100 |
| Package Type | Micro FBGA-100 (MBGA), 6 x 6 mm, 0.5 mm pitch |
| Pin-to-Pin Delay (tPD) | 5.4 ns |
| Maximum Frequency | 201.1 MHz |
| Suhu Operasi | -40C to +125C (industrial) |
| Tegangan Pemberi Arus | 1.8 V core (MultiVolt I/O 1.5 V to 3.3 V) |
| Program Memory Type | Flash (non-volatile, in-system programmable) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Jenis Pemasangan | Surface Mount |
| Lead Free / RoHS | Yes / Compliant |
| Logic Family | CMOS |
Panduan Konfigurasi Pin EPM570GM100C5N micro fbga-100 (mbga), 6 x 6 mm, 0.5 mm pitch
Konfigurasi pin untuk EPM570GM100C5N (micro fbga-100 (mbga), 6 x 6 mm, 0.5 mm pitch pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk EPM570GM100C5N.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
EPM570GM100C5N patut untuk 7 aplikasis: I/O Expansion and Bus Bridging, FPGA / ASIC Power Sequencing, Industrial Control and PLC Logic, JTAG Chain Management and Configuration Control, Address Decoding Glue Logic, LED Display Refresh and Driver Logic, Communication Protocol Bridging (UART / SPI / I2C).
I/O Expansion and Bus Bridging
The EPM570GM100C5N's 440 macrocells and 76 user I/Os make it ideal for expanding a microcontroller's GPIO count and bridging between mismatched bus widths such as SPI to parallel or 8-bit to 16-bit. With 5.4 ns pin-to-pin delay and 201.1 MHz fMAX, the part handles real-time bus protocol conversion without adding latency. The MultiVolt I/O interface (1.5 V to 3.3 V) directly interfaces with mixed-voltage peripherals, eliminating external level shifters. Compared to discrete 74-series glue logic, a single CPLD replaces dozens of gates and is reconfigurable in-system via JTAG.
Disebarkan
FPGA / ASIC Power Sequencing
The EPM570GM100C5N is widely used to sequence multiple power rails for FPGA and ASIC bring-up. Its non-volatile flash-based instant-on architecture means the CPLD is operational within microseconds of power-up, before the main FPGA has finished configuration. The 76 user I/Os can drive PG (power-good) signals, EN lines, and reset multiplexers across an entire board. The 1.8 V core with MultiVolt I/O interfaces directly to standard POL converter enable pins. Compared to a discrete sequencer IC, the CPLD offers unlimited sequencing patterns and field updates.
Disebarkan
Industrial Control and PLC Logic
The EPM570GM100C5N's industrial -40C to +125C operating range and robust flash configuration make it suitable for industrial PLC, motor drive, and process-control logic. The 440 macrocells handle typical encoder decoding, PWM generation, and safety interlock logic that previously required multiple discrete timers and gates. The non-volatile instant-on behavior ensures deterministic behavior at every power cycle, critical for safety-certified industrial systems. The MBGA-100 footprint supports compact, vibration-resistant PCB layouts.
Disebarkan
JTAG Chain Management and Configuration Control
Designers use the EPM570GM100C5N as a JTAG controller or chain multiplexer to manage shared JTAG buses between FPGAs, flash memory, and processors. The CPLD's 76 I/Os can drive TMS, TCK, TDI, TDO signals with proper buffering, while the flash-backed configuration stores the JTAG topology non-volatilely. The 5.4 ns tPD supports TCK frequencies up to 100 MHz in chain multiplexing applications. Compared to a discrete JTAG switch IC, the CPLD adds custom test-pattern generation and boundary-scan support.
Disebarkan
Address Decoding Glue Logic
The EPM570GM100C5N's 440 macrocells and 76 user I/Os are well-suited for memory and peripheral address-decoding tasks in microprocessor systems. By replacing dozens of 74HC138 / 74HC139 decoder chips with a single CPLD, designers save PCB area and gain flexibility for late-stage address map changes. The 5.4 ns tPD adds negligible access-time penalty, while the MultiVolt I/O interface bridges between modern 1.8 V processors and legacy 3.3 V peripherals. JTAG-based in-system reprogramming lets designers iterate without respinning PCBs.
Disebarkan
LED Display Refresh and Driver Logic
The EPM570GM100C5N drives multiplexed LED matrix displays by generating row-select timing, PWM dimming waveforms, and refresh control. With 76 user I/Os, the CPLD directly interfaces to 8-16 row LED matrices without external drivers. The 201.1 MHz internal frequency supports high PWM resolution for color depth, while the flash-based architecture eliminates boot-PROM complexity. The MultiVolt I/O interfaces to both 3.3 V LED driver ICs and 5 V legacy displays, simplifying mixed-voltage designs.
Disebarkan
Communication Protocol Bridging (UART / SPI / I2C)
The EPM570GM100C5N bridges between UART, SPI, I2C, and custom serial protocols in embedded systems. The 440 macrocells implement multiple protocol state machines in parallel, and the 76 user I/Os drive multiple bus instances simultaneously. The 5.4 ns tPD supports SPI clock rates up to 100 MHz with deterministic timing. The MultiVolt I/O (1.5 V to 3.3 V) bridges between modern low-voltage MCUs and legacy 3.3 V peripherals, eliminating external level shifters. JTAG-based field updates enable protocol patches in deployed equipment.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk EPM570GM100C5N — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | EPM570GM100I5N | EPM570GM100C4N | EPM570F100C5N | EPM570F100I5N | EPM570F100C4N | EPM570F100A5N |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | Micro FBGA-100 (MBGA), 6x6 mm | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same |
| Macro Cells | 440 | 440 | 440 | 440 | 440 | 440 | 440 |
| Pin-to-Pin Delay (tPD) | 5.4 ns | 5.0 ns | 4.5 ns | 5.4 ns | 5.0 ns | 4.5 ns | 5.0 ns |
| Maximum Frequency | 201.1 MHz | 222.2 MHz | 304 MHz | 201.1 MHz | 222.2 MHz | 304 MHz | 222.2 MHz |
| Operating Temperature | -40C to +125C (industrial) | -40C to +125C (industrial) | 0C to +85C (commercial) | -40C to +125C (industrial) | -40C to +125C (industrial) | 0C to +85C (commercial) | -40C to +125C (industrial) |
| User I/Os | 76 | 76 | 76 | 76 | 76 | 76 | 76 |
| Series Variant | G-series | G-series | G-series | F-series | F-series | F-series | F-series |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
Penyeberangsung Jelas
- Industrial temperature grade with -40C to +125C rating (vsEPM570GM100C5 (commercial, no 'N' suffix))
- 5.4 ns tPD with non-volatile instant-on configuration (vsEPM570GM100C4N)
- G-series silicon with full MAX II feature set (vsEPM570F100C5N (F-series variant))
Catatan Desain
The Micro FBGA-100 (6 x 6 mm, 0.5 mm pitch) requires careful PCB layout. Use NSMD (non-solder mask defined) pads with a diameter approximately 80% of the ball diameter for reliable BGA reflow. Micro-vias under the BGA are acceptable with stacked-via or staggered-via structures; dog-bone fan-out is recommended for inner rows when escape routing is constrained. Per IPC-7093, BGA pad finishes should use ENIG or OSP for consistent wetting, and reflow profile must follow J-STD-020 MSL classification.
The MultiVolt I/O interface (1.5 V to 3.3 V) simplifies mixed-voltage designs but does not eliminate the need for series damping resistors on long PCB traces. For signals routed longer than 50 mm (about 1.6 inches) on FR-4, add 22-33 ohm series resistors to dampen reflections. The 201.1 MHz fMAX supports high-speed protocol bridges; for SPI clocks above 50 MHz, controlled-impedance routing (50 ohm single-ended) is recommended.
Do not omit the JTAG chain integrity check when sharing the JTAG bus with other programmable devices. Pull TMS and TCK high during power-up to keep the JTAG TAP controller in a known state. The flash-based configuration requires a valid VCCIO during programming; programming with VCCIO below 1.5 V can corrupt the configuration memory and require a re-programming cycle. Always verify the JTAG IDCODE after programming to confirm successful configuration.
Estimated: at typical 1.8 V core supply and 100% toggle rate, the EPM570GM100C5N dissipates approximately 100 mW during normal operation. The MBGA-100 package has a theta-JA of approximately 35-40 C/W on a 4-layer JEDEC test board, yielding a junction temperature rise of 3-4 C above ambient. No external heatsink is required, but adequate airflow is recommended in enclosed industrial enclosures operating above 70 C ambient. De-rate maximum toggle rate by 10-15% above 100 C ambient.
Maklumat Kesediaan
RoHS and lead-free compliant per Intel product page. Industrial -40C to +125C operating range. Not AEC-Q100 qualified for automotive; for automotive-grade alternatives consider MAX V CPLD family with AEC-Q100 documentation.
