EPM570GM100C5N - 440 Macrocell MAX II CPLD, 100-MBGA | Intel
MPN: EPM570GM100C5N ✓ NakahandaEPM570GM100C5N Ulas
A CPLD (Complex Programmable Logic Device) is a non-volatile, flash-based programmable logic device that sits in the hierarchy between simple PLDs and full FPGAs. CPLDs are widely used for I/O expansion, bus bridging, power-up sequencing, and glue-logic functions where deterministic timing and instant-on behavior are required. The MAX II family pioneered low-cost, low-power CPLDs based on a look-up table (LUT) architecture, offering higher logic density than traditional PAL/GAL devices while keeping non-volatile instant-on capability.
Key features of the EPM570GM100C5N include 440 logic elements (macro cells), a flash-based non-volatile configuration memory that eliminates external boot PROM, in-system programmability via JTAG, MultiVolt core supporting I/O voltages from 1.5 V to 3.3 V, and an internal oscillator. The MultiVolt I/O interface allows the part to bridge between 3.3 V, 2.5 V, 1.8 V, and 1.5 V logic families without external level shifters, simplifying mixed-voltage PCB designs.
The device's flash-backed architecture provides true instant-on operation - the device is functional within microseconds of power-up. The 100-ball MBGA package supports high-density board layouts while keeping the footprint compact at 6 x 6 mm, suitable for space-constrained industrial, consumer, and communications designs.
Typical applications include I/O expansion and bus bridging in industrial controllers, power-up/power-down sequencing logic for FPGA and ASIC rails, JTAG-controlled configuration management, LED display driving and refresh, and address decoding glue logic between processors and peripherals. Designers frequently select the EPM570 family for designs that previously required multiple 74-series logic devices, since one CPLD replaces dozens of discrete gates while adding reconfigurability.
Design consideration: when migrating between speed grades (C4, C5, C5N, I5N), verify that the timing closure margins remain acceptable. The C5N industrial grade (-40C to +125C) is preferred for harsh-environment deployments, while commercial C5 is suitable for cost-sensitive consumer designs. Always observe JTAG chain integrity when the CPLD shares the JTAG bus with other programmable devices.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.
Mga alternatibo na pwedeng ilagay na EPM570GM100C5N — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok EPM570GM100C5N (parehas na form factor at footprint) — pagkakaiba sa Operating Temperature, Package, Process Technology, Programming Interface, Configuration Memory.
EPM570GM100I5N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →EPM570GM100C4N
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
EPM570F100C5N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →EPM570F100I5N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →EPM570F100C4N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →EPM570F100A5N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →EPM570GM100C5N Mga Pinakamataas na Rating at Electrical Characteristics
| Family | MAX II |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Macro Cells | 440 |
| User I/Os | 76 |
| Logic Elements | 440 |
| Bilang ng Pins | 100 |
| Package Type | Micro FBGA-100 (MBGA), 6 x 6 mm, 0.5 mm pitch |
| Pin-to-Pin Delay (tPD) | 5.4 ns |
| Maximum Frequency | 201.1 MHz |
| Temperature na Operasyon | -40C to +125C (industrial) |
| Volte ng Pagbibigay | 1.8 V core (MultiVolt I/O 1.5 V to 3.3 V) |
| Program Memory Type | Flash (non-volatile, in-system programmable) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Uri ng Pagpapasok | Surface Mount |
| Lead Free / RoHS | Yes / Compliant |
| Logic Family | CMOS |
Gabay sa Pin Configuration ng EPM570GM100C5N micro fbga-100 (mbga), 6 x 6 mm, 0.5 mm pitch
Pin configuration para sa EPM570GM100C5N (micro fbga-100 (mbga), 6 x 6 mm, 0.5 mm pitch package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa EPM570GM100C5N.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
EPM570GM100C5N ay nararapat para sa 7 aplikasyons: I/O Expansion and Bus Bridging, FPGA / ASIC Power Sequencing, Industrial Control and PLC Logic, JTAG Chain Management and Configuration Control, Address Decoding Glue Logic, LED Display Refresh and Driver Logic, Communication Protocol Bridging (UART / SPI / I2C).
I/O Expansion and Bus Bridging
The EPM570GM100C5N's 440 macrocells and 76 user I/Os make it ideal for expanding a microcontroller's GPIO count and bridging between mismatched bus widths such as SPI to parallel or 8-bit to 16-bit. With 5.4 ns pin-to-pin delay and 201.1 MHz fMAX, the part handles real-time bus protocol conversion without adding latency. The MultiVolt I/O interface (1.5 V to 3.3 V) directly interfaces with mixed-voltage peripherals, eliminating external level shifters. Compared to discrete 74-series glue logic, a single CPLD replaces dozens of gates and is reconfigurable in-system via JTAG.
Inirekomenda
FPGA / ASIC Power Sequencing
The EPM570GM100C5N is widely used to sequence multiple power rails for FPGA and ASIC bring-up. Its non-volatile flash-based instant-on architecture means the CPLD is operational within microseconds of power-up, before the main FPGA has finished configuration. The 76 user I/Os can drive PG (power-good) signals, EN lines, and reset multiplexers across an entire board. The 1.8 V core with MultiVolt I/O interfaces directly to standard POL converter enable pins. Compared to a discrete sequencer IC, the CPLD offers unlimited sequencing patterns and field updates.
Inirekomenda
Industrial Control and PLC Logic
The EPM570GM100C5N's industrial -40C to +125C operating range and robust flash configuration make it suitable for industrial PLC, motor drive, and process-control logic. The 440 macrocells handle typical encoder decoding, PWM generation, and safety interlock logic that previously required multiple discrete timers and gates. The non-volatile instant-on behavior ensures deterministic behavior at every power cycle, critical for safety-certified industrial systems. The MBGA-100 footprint supports compact, vibration-resistant PCB layouts.
Inirekomenda
JTAG Chain Management and Configuration Control
Designers use the EPM570GM100C5N as a JTAG controller or chain multiplexer to manage shared JTAG buses between FPGAs, flash memory, and processors. The CPLD's 76 I/Os can drive TMS, TCK, TDI, TDO signals with proper buffering, while the flash-backed configuration stores the JTAG topology non-volatilely. The 5.4 ns tPD supports TCK frequencies up to 100 MHz in chain multiplexing applications. Compared to a discrete JTAG switch IC, the CPLD adds custom test-pattern generation and boundary-scan support.
Inirekomenda
Address Decoding Glue Logic
The EPM570GM100C5N's 440 macrocells and 76 user I/Os are well-suited for memory and peripheral address-decoding tasks in microprocessor systems. By replacing dozens of 74HC138 / 74HC139 decoder chips with a single CPLD, designers save PCB area and gain flexibility for late-stage address map changes. The 5.4 ns tPD adds negligible access-time penalty, while the MultiVolt I/O interface bridges between modern 1.8 V processors and legacy 3.3 V peripherals. JTAG-based in-system reprogramming lets designers iterate without respinning PCBs.
Inirekomenda
LED Display Refresh and Driver Logic
The EPM570GM100C5N drives multiplexed LED matrix displays by generating row-select timing, PWM dimming waveforms, and refresh control. With 76 user I/Os, the CPLD directly interfaces to 8-16 row LED matrices without external drivers. The 201.1 MHz internal frequency supports high PWM resolution for color depth, while the flash-based architecture eliminates boot-PROM complexity. The MultiVolt I/O interfaces to both 3.3 V LED driver ICs and 5 V legacy displays, simplifying mixed-voltage designs.
Inirekomenda
Communication Protocol Bridging (UART / SPI / I2C)
The EPM570GM100C5N bridges between UART, SPI, I2C, and custom serial protocols in embedded systems. The 440 macrocells implement multiple protocol state machines in parallel, and the 76 user I/Os drive multiple bus instances simultaneously. The 5.4 ns tPD supports SPI clock rates up to 100 MHz with deterministic timing. The MultiVolt I/O (1.5 V to 3.3 V) bridges between modern low-voltage MCUs and legacy 3.3 V peripherals, eliminating external level shifters. JTAG-based field updates enable protocol patches in deployed equipment.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for EPM570GM100C5N — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | EPM570GM100I5N | EPM570GM100C4N | EPM570F100C5N | EPM570F100I5N | EPM570F100C4N | EPM570F100A5N |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | Micro FBGA-100 (MBGA), 6x6 mm | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same | Micro FBGA-100 (MBGA) - same |
| Macro Cells | 440 | 440 | 440 | 440 | 440 | 440 | 440 |
| Pin-to-Pin Delay (tPD) | 5.4 ns | 5.0 ns | 4.5 ns | 5.4 ns | 5.0 ns | 4.5 ns | 5.0 ns |
| Maximum Frequency | 201.1 MHz | 222.2 MHz | 304 MHz | 201.1 MHz | 222.2 MHz | 304 MHz | 222.2 MHz |
| Operating Temperature | -40C to +125C (industrial) | -40C to +125C (industrial) | 0C to +85C (commercial) | -40C to +125C (industrial) | -40C to +125C (industrial) | 0C to +85C (commercial) | -40C to +125C (industrial) |
| User I/Os | 76 | 76 | 76 | 76 | 76 | 76 | 76 |
| Series Variant | G-series | G-series | G-series | F-series | F-series | F-series | F-series |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
Pangunahing mga Pagkakaiba
- Industrial temperature grade with -40C to +125C rating (kumpara saEPM570GM100C5 (commercial, no 'N' suffix))
- 5.4 ns tPD with non-volatile instant-on configuration (kumpara saEPM570GM100C4N)
- G-series silicon with full MAX II feature set (kumpara saEPM570F100C5N (F-series variant))
Talaan ng Disenyo
The Micro FBGA-100 (6 x 6 mm, 0.5 mm pitch) requires careful PCB layout. Use NSMD (non-solder mask defined) pads with a diameter approximately 80% of the ball diameter for reliable BGA reflow. Micro-vias under the BGA are acceptable with stacked-via or staggered-via structures; dog-bone fan-out is recommended for inner rows when escape routing is constrained. Per IPC-7093, BGA pad finishes should use ENIG or OSP for consistent wetting, and reflow profile must follow J-STD-020 MSL classification.
The MultiVolt I/O interface (1.5 V to 3.3 V) simplifies mixed-voltage designs but does not eliminate the need for series damping resistors on long PCB traces. For signals routed longer than 50 mm (about 1.6 inches) on FR-4, add 22-33 ohm series resistors to dampen reflections. The 201.1 MHz fMAX supports high-speed protocol bridges; for SPI clocks above 50 MHz, controlled-impedance routing (50 ohm single-ended) is recommended.
Do not omit the JTAG chain integrity check when sharing the JTAG bus with other programmable devices. Pull TMS and TCK high during power-up to keep the JTAG TAP controller in a known state. The flash-based configuration requires a valid VCCIO during programming; programming with VCCIO below 1.5 V can corrupt the configuration memory and require a re-programming cycle. Always verify the JTAG IDCODE after programming to confirm successful configuration.
Estimated: at typical 1.8 V core supply and 100% toggle rate, the EPM570GM100C5N dissipates approximately 100 mW during normal operation. The MBGA-100 package has a theta-JA of approximately 35-40 C/W on a 4-layer JEDEC test board, yielding a junction temperature rise of 3-4 C above ambient. No external heatsink is required, but adequate airflow is recommended in enclosed industrial enclosures operating above 70 C ambient. De-rate maximum toggle rate by 10-15% above 100 C ambient.
Impormasyon ng Pagsunod sa Kautusan
RoHS and lead-free compliant per Intel product page. Industrial -40C to +125C operating range. Not AEC-Q100 qualified for automotive; for automotive-grade alternatives consider MAX V CPLD family with AEC-Q100 documentation.
