KSZ8842-16MVLI - 2-Port 10/100 Ethernet Switch | Microchip
MPN: KSZ8842-16MVLI ✓ AktifKSZ8842-16MVLI Ringkasan
An Ethernet switch is a network-interface device that forwards Ethernet frames between attached ports while using a parallel host interface to exchange data and control information with an embedded processor. The KSZ8842 family sits within the Ethernet interface IC hierarchy: Ethernet switch controller, then network interface controller, then integrated interface circuit. Its 2-port arrangement supports compact embedded systems that require more than one wired-network connection without requiring a separate switch for each port.
The KSZ8842-16MVLI provides two 10/100 Base-T/TX ports, a generic 8/16-bit parallel interface, MII and cable-diagnostics support, programmable LED outputs, and a low-power operating mode. The listed operating supply range is 3.1 V to 3.5 V. These functions make it suitable for industrial controllers, embedded gateways, set-top equipment, and other systems that need two Fast Ethernet links connected through one parallel CPU bus.
The controller is intended for systems using a non-PCI parallel CPU interface. Its bus architecture allows 8-bit or 16-bit embedded-host operation, while the integrated switch manages communication between the two Ethernet ports. Because the device combines host-interface and network-switch functions, firmware must correctly configure port speed, duplex behavior, link status, and any low-power-mode transitions for its target platform.
The KSZ8842 family includes PCI and non-PCI CPU-interface implementations. The KSZ8842-16MVLI is the non-PCI, 8/16-bit parallel-interface member, so it should not be confused with the PCI-interface KSZ8842-PMQL or KSZ8842-PMBL variants. It also differs from 32-bit bus members of the same family, which target a wider host data path.
PCB implementation should preserve the 128-LQFP footprint and route the parallel bus, magnetics, Ethernet differential pairs, clock, reset, and control signals according to the manufacturer datasheet. Keep the Ethernet magnetics close to the corresponding ports and maintain controlled differential impedance to reduce reflections and radiated emissions.
This product record consolidates electrical limits, package information, interface functions, sourcing guidance, and verified replacement considerations. The comparison also distinguishes genuine footprint-compatible options from related family members whose bus width, port count, interface type, or package prevents unqualified drop-in use.
Pilihan pengganti yang segera untuk KSZ8842-16MVLI — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera KSZ8842-16MVLI (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type.
KSZ8842-16MVL
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
KSZ8842-16MVLI Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 2-Port 10/100 Ethernet Switch with Parallel CPU Interface |
| Number of Ethernet Ports | 2 ports |
| Ethernet Data Rate | 10/100 Mb/s per port |
| Ethernet Standards | IEEE 802.3, IEEE 802.3u, IEEE 802.3x |
| CPU Interface | Generic 8/16-bit parallel bus |
| Jenis Antaramuka | Non-PCI parallel CPU interface |
| MII Support | Supported |
| Cable Diagnostics | Supported |
| Programmable LED Indication | Supported |
| Low-Power Mode | Supported |
| Minimum Supply Voltage | 3.1 V |
| Maximum Supply Voltage | 3.5 V |
| Kemasan | 128-LQFP, 14 mm x 14 mm |
| Jenis Pemasangan | Surface mount |
| Maximum Data Rate | 100 Mb/s |
| Kiraan Pin | 128 pins |
Panduan Konfigurasi Pin KSZ8842-16MVLI 128-lqfp, 14 mm x 14 mm
Konfigurasi pin untuk KSZ8842-16MVLI (128-lqfp, 14 mm x 14 mm pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk KSZ8842-16MVLI.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
KSZ8842-16MVLI patut untuk 6 aplikasis: Industrial Ethernet Gateway, Embedded Network Bridge, Set-Top Network Endpoint, Cable Diagnostic Test Fixture, Low-Power Control Panel, Machine-to-Machine Connectivity.
Industrial Ethernet Gateway
The KSZ8842-16MVLI fits an industrial gateway that needs two 10/100 Mb/s Ethernet connections and a straightforward embedded host interface. One port can connect the gateway to a supervisory network while the second links a local machine or sensor network, reducing the need for separate Ethernet switch silicon. Its generic 8/16-bit parallel CPU interface is appropriate for processors that do not implement PCI, and the 3.1 V to 3.5 V supply range fits a regulated 3.3 V rail. Cable diagnostics and programmable LED indication help commissioning personnel identify wiring or link problems, while low-power mode can reduce consumption when the equipment is idle.
Disebarkan
Embedded Network Bridge
The KSZ8842-16MVLI can serve as the forwarding element in a compact embedded Ethernet bridge. Its two switched 10/100 Mb/s ports allow one network segment to be connected to another through an embedded processor, rather than implementing two independent host-side PHYs. The generic 8/16-bit parallel interface provides a practical host path for a resource-constrained controller, and MII support expands integration options. Designers should allocate the 128-LQFP footprint correctly, preserve short Ethernet differential routes to the magnetics, and validate frame buffering, flow-control, and low-power transitions in the complete network design.
Disebarkan
Set-Top Network Endpoint
The KSZ8842-16MVLI is appropriate for set-top and consumer-network equipment that needs two Fast Ethernet paths through one controller. A service port can connect to a local management network while the second port carries access traffic, and the parallel CPU interface can serve embedded Linux or real-time control firmware. Programmable LEDs allow the enclosure indicators to show link, activity, or fault status, while cable diagnostics provide useful field troubleshooting. The main board-level consideration is the relatively large 128-LQFP footprint compared with compact single-port Ethernet controllers.
Disebarkan
Cable Diagnostic Test Fixture
The KSZ8842-16MVLI can support an automated cable-test fixture because its Ethernet interface includes cable-diagnostics support and programmable LED indication. Two 10/100 Mb/s ports permit connection to test equipment and the cable under examination, while the generic 8/16-bit parallel interface transfers results to a test controller. The 3.1 V to 3.5 V operating range is compatible with a regulated 3.3 V test-board rail. Firmware should interpret the manufacturer's diagnostic status correctly and coordinate any remote-pair or link-state reporting, since the device is a network switch controller rather than a standalone cable tester.
Disebarkan
Low-Power Control Panel
The KSZ8842-16MVLI fits network-enabled control panels that require two Ethernet connections but need to reduce activity during idle periods. Its low-power mode allows the system firmware to manage energy use without removing all network capability, while programmable LEDs can provide operator-visible link status. The generic 8/16-bit parallel interface avoids a PCI requirement and can connect to a modest embedded controller. Because the package exposes 128 leads, panel designers should confirm that the board has adequate routing density and place the device to shorten parallel-bus and Ethernet differential routes.
Disebarkan
Machine-to-Machine Connectivity
The KSZ8842-16MVLI can support machine-to-machine connectivity where a controller must communicate over two 10/100 Mb/s Ethernet links. One link may connect supervisory equipment and the other a local machine controller, while diagnostics help identify cable faults during installation. The generic 8/16-bit parallel CPU interface is suitable for embedded processors without PCI, and a 3.3 V system rail aligns with the listed 3.1 V to 3.5 V supply range. For industrial deployment, verify operating-temperature limits, electromagnetic-emissions requirements, grounding, and isolation architecture in addition to the controller's electrical specifications.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk KSZ8842-16MVLI — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | KSZ8842-16MVL |
|---|---|---|
| Package | 128-LQFP (14x14) | 128-LQFP (14x14) |
| Brand | Microchip Technology | Microchip Technology |
| Ethernet Port Count | 2 ports | 2 ports |
| Data Rate | 10/100 Mb/s | 10/100 Mb/s |
| CPU Interface | Generic 8/16-bit parallel bus | Generic 8/16-bit parallel bus |
| CPU Interface Type | Non-PCI | Non-PCI |
| Supply Voltage Range | 3.1 V to 3.5 V | 3.1 V to 3.5 V |
| Cable Diagnostics | Supported | Supported |
| Programmable LED Indication | Supported | Supported |
| Low-Power Mode | Supported | Supported |
| Ethernet Standards | IEEE 802.3, IEEE 802.3u, IEEE 802.3x | IEEE 802.3, IEEE 802.3u, IEEE 802.3x |
| Mounting Type | Surface mount | Surface mount |
Penyeberangsung Jelas
- Combines two Fast Ethernet ports with one non-PCI host interface (vsKSZ8842-16MVL)
- Cable diagnostics improve installed-network troubleshooting (vsKSZ8842-16MVL)
- Programmable LED indication supports product-specific status reporting (vsKSZ8842-16MVL)
- Low-power mode complements embedded network designs (vsKSZ8842-16MVL)
Catatan Desain
Place the KSZ8842-16MVLI so the Ethernet differential pairs connect directly to their corresponding magnetics with no unnecessary stubs or layer transitions. Route the generic 8/16-bit parallel bus away from the Ethernet pairs and magnetics where practical. Use the manufacturer reference layout and layer stack for impedance geometry, especially on a 128-LQFP footprint where parallel signals can introduce crosstalk if routed carelessly.
Design the 3.3 V supply rail to remain within the listed 3.1 V to 3.5 V operating range during startup, load transients, and temperature extremes. Place local high-frequency bypass capacitors close to the device supply pins and isolate noisy digital return currents from Ethernet magnetics. Confirm the exact pin-level decoupling network, current limits, and sequencing requirements in the manufacturer datasheet before finalizing the power tree.
Do not treat related KSZ8842, KSZ8863, or KSZ8873 devices as interchangeable merely because they share the KSZ family name. Verify port count, CPU-interface type, bus width, package, pin assignments, voltage, clocking, and Ethernet magnetics. The KSZ8842-32MVLI uses a wider bus, while the PCI-interface KSZ8842-PMQL and KSZ8842-PMBL use different packages and interfaces.
Validate the parallel CPU-bus timing in the assembled board, with particular attention to clock jitter, propagation delay, loading, and crosstalk from adjacent signals. Use the manufacturer's recommended host-bus topology and avoid adding long diagnostic or expansion branches to the bus. MII support does not remove the need for controlled impedance and disciplined clock routing when that interface is enabled.
Maklumat Kesediaan
The manufacturer product family and comparison listings reference RoHS and REACH topics, but an explicit compliance declaration for this exact order code was not established. Confirm material and environmental declarations with Microchip Technology before final procurement approval.