Texas Instruments

DS90CR562MTD - 18-Bit LVDS FPD-Link Receiver | Texas Instruments

MPN: DS90CR562MTD ✓ Active
4.5 V to 5.5 V Vdss 48-TFSOP, 0.240 inch, 6.10 mm width Package Phase-locked transmit clock transmitted in parallel Speed
MOQ: 1 |

DS90CR562MTD Overview

The Texas Instruments DS90CR562MTD is a 21-bit LVDS receiver for 18-bit color flat-panel display links, operating from a 4.5 V to 5.5 V supply and packaged in a 48-pin TSSOP. It is designed to receive three LVDS data streams carrying 18-bit RGB pixel data and a transmitted phase-locked clock. The receiver supports CMOS/TTL-compatible downstream display interfaces and is positioned for compact flat-panel display systems, industrial monitors, and legacy LVDS display-control equipment.

An LVDS receiver is an interface circuit that restores low-voltage differential signaling data at the display end of a link. FPD-Link is a display-oriented interface standard that transports parallel video data over differential pairs. In the DS90CR562MTD, the LVDS input stage recovers three data streams and separates the transmitted clock information, allowing a display controller or timing circuit to reconstruct pixel data.

The principal electrical characteristics include a 4.5 V to 5.5 V supply range, 21 receiver inputs, three data streams, and LVDS protocol support. The package is a 48-TSSOP, also identified in the product listing as 48-TFSOP with a 0.240 inch, 6.10 mm width. The listed packaging format is Tube, and the device is categorized as an interface IC for specialized display-link applications.

The DS90CR562MTD is primarily intended for systems using the National Semiconductor DS90CR561 transmitter and DS90CR562 receiver family. Its architecture supports the transfer of 18-bit color information over an LVDS display link rather than conventional parallel RGB wiring. This can reduce signal-routing complexity and support a more compact connection between a display engine and a flat-panel display timing controller.

Designers should verify differential pair routing, LVDS input impedance, termination strategy, supply decoupling, and the exact display timing requirements of the target panel before releasing a PCB layout. The receiver is a digital interface device, so a conventional power-semiconductor safe-operating-area chart does not apply. Compliance status should be confirmed against the manufacturer’s current product documentation for the exact ordering code.

This page combines the documented DS90CR562MTD interface and package information with application guidance, comparison parameters, and drop-in replacement analysis for engineers evaluating display-link receiver designs.

Drop-in alternatives for DS90CR562MTD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with DS90CR562MTD (same form factor and footprint) — differing in Package Type, Product Type, Package.

Texas Instruments
Package Type: TSSOP
Compare with DS90CR562MTD →
Texas Instruments
Package Type: TSSOP-48
Product Type: LVDS line receiver IC
Compare with DS90CR562MTD →
Texas Instruments
Product Type: 21-bit Channel Link line driver interface IC
Package: 48-terminal TSSOP
Compare with DS90CR562MTD →

DS90CF562MTD

✅ Drop-In
Texas Instruments
📦 48-TSSOP
LVDS 18-bit color flat-panel display link interface IC · 21 bits CMOS/TTL in the DS90CF561/DS90CF562 family · 3 streams in the DS90CF561/DS90CF562 family · Phase-locked transmit clock transmitted in parallel · 18 bits · TSSOP · 48 pins · Gull wing

Contact for price

View Datasheet →

DS90CR213MTD

✅ Drop-In
Texas Instruments
📦 48-TSSOP
21-bit Channel Link line driver interface IC · 21 bits · 66 MHz · 5.25 V · EIA-644 / TIA-644 · -10°C to +70°C · Commercial · 48-terminal TSSOP

Contact for price

View Datasheet →

DS90CR561MTD

✅ Drop-In
Texas Instruments
📦 48-TSSOP
Interface IC · LVDS Flat Panel Display · Texas Instruments · National Semiconductor · 48-pin TSSOP · 48 pins · Surface mount · 0.45 V

Contact for price

View Datasheet →

DS90CR561AQT

✅ Drop-In ⚠️ Specs Unverified
📦 48-TSSOP
Same 48-TSSOP DS90CR561 family and transmitter role; device revision and timing characteristics require comparison before board substitution

📋 Reference alternative (not in catalog)

DS90CR562AQT

✅ Drop-In ⚠️ Specs Unverified
📦 48-TSSOP
Same 48-TSSOP DS90CR562 receiver family; revision-specific timing, marking, and production-code differences require datasheet verification

📋 Reference alternative (not in catalog)

DS90CR562MTD Specifications

Product Type LVDS 18-bit color flat-panel display link receiver
Number of Drivers/Receivers 3/21
Receiver Input Count 21
LVDS Data Stream Count 3
Supply Voltage Range 4.5 V to 5.5 V
Protocol FPD-Link, LVDS
Signal Standard LVDS (Low Voltage Differential Signaling)
Transmitted Data 21 bits of CMOS/TTL data
Color Data Width 18 bit
Clock Transmission Phase-locked transmit clock transmitted in parallel
Package 48-TFSOP, 0.240 inch, 6.10 mm width
Package Type 48-pin TSSOP
Mounting Type Surface Mount
Packaging Format Tube

DS90CR562MTD 48-pin tssop Pin Configuration Guide

Pin configuration for DS90CR562MTD (48-pin tssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

48-pin tssop package pinout diagram for DS90CR562MTD

No detailed pinout data available for DS90CR562MTD.

Refer to the datasheet for full pin configuration.

Typical Applications

DS90CR562MTD is suitable for 6 applications: Industrial Flat-Panel Monitor Receiver, Digital Video Display Interface, Medical Diagnostic Display, Point-of-Sale Terminal Display, Video Processing System, Legacy Monitor Repair or Board Reuse.

🖥️

Industrial Flat-Panel Monitor Receiver

The DS90CR562MTD fits an industrial flat-panel monitor built around the DS90CR561/DS90CR562 display link because it receives three LVDS data streams carrying the 18-bit color path and uses a parallel phase-locked clock. The 4.5 V to 5.5 V operating range supports a conventional 5 V receiver rail, while the 48-TSSOP package enables a compact interface section beside the display timing electronics. For an industrial design, confirm the panel’s supported color depth, timing range, clock recovery expectations, and exact differential-pair mapping. Also review temperature limits and EMC requirements against the manufacturer documentation before production release.

📺

Digital Video Display Interface

DS90CR562MTD is appropriate for a digital video display interface that carries parallel color data from a display engine to a panel timing controller. The receiver accepts the three differential data streams created from 21 CMOS/TTL bits and receives the phase-locked clock through the parallel clock path described for the DS90CR561/DS90CR562 family. This architecture reduces the number of high-speed point-to-point traces compared with a direct 18-bit parallel RGB route. The board designer must preserve differential pair geometry, provide a compliant LVDS interconnect, and verify that the panel controller accepts the recovered data and clock timing.

💊

Medical Diagnostic Display

The DS90CR562MTD can support the digital video connection of a medical diagnostic display when the display uses the matching DS90CR561/DS90CR562 FPD-Link architecture. Its three-LVDS-stream interface and parallel phase-locked clock path provide a compact connection for transferring 18-bit color data between the acquisition or processing electronics and the display timing circuit. The receiver itself does not define diagnostic-image accuracy, so system validation must cover bit integrity, panel timing, grounding, shielding, and any medical electrical requirements. Use the manufacturer datasheet to confirm supply limits, temperature range, and the exact receiver pin assignments.

🖥️

Point-of-Sale Terminal Display

DS90CR562MTD is suitable for the internal display interface of a point-of-sale terminal or compact kiosk when the panel controller uses the National Semiconductor 18-bit color FPD-Link architecture. The receiver helps replace a wide parallel display bus with three LVDS data streams and a parallel clock path, which can simplify routing around a dense system board. The 48-TSSOP package provides a compact receiver footprint, and the 4.5 V to 5.5 V range aligns with a standard 5 V rail. Before deployment, verify refresh rate, resolution, panel clock tolerance, startup behavior, connector pinout, and the thermal environment inside the enclosure.

🎥

Video Processing System

The DS90CR562MTD fits a video-processing system that separates pixel transport from local display timing. A DS90CR561-family transmitter converts 21 bits of CMOS/TTL data into three LVDS streams, and the DS90CR562MTD provides the receiving side of that display link with the phase-locked transmit clock carried in parallel. This arrangement is useful when the processor, scaler, or display controller is separated from the panel connector by several centimeters of PCB routing. Signal-integrity work must ensure compliant differential impedance, controlled pair length matching, suitable connector transitions, and a clock distribution plan that meets the receiver and panel timing requirements.

🔧

Legacy Monitor Repair or Board Reuse

DS90CR562MTD is relevant to repair and board-reuse projects involving an established LVDS flat-panel display link based on the National Semiconductor DS90CR561/DS90CR562 architecture. Because the receiver uses a 48-TSSOP package and operates from 4.5 V to 5.5 V, it can support direct design-in when the original footprint and interfaces are confirmed. A repair should not begin from the part number alone: compare every supply, ground, differential input, clock, enable, and no-connect position with the manufacturer pin table. Validate the replacement against the actual display timing and check for obsolete companion components elsewhere in the board.

What is the DS90CR562MTD?
The DS90CR562MTD is a 48-pin TSSOP receiver for 18-bit color flat-panel display links using LVDS and FPD-Link signaling. According to the National Semiconductor DS90CR561/DS90CR562 datasheet information, it receives three LVDS data streams that carry 21 bits of CMOS/TTL display data, with the phase-locked transmit clock carried in parallel. It operates from a 4.5 V to 5.5 V supply and is intended for display systems using an LVDS link rather than a direct parallel RGB connection.
What are the key specifications of DS90CR562MTD?
The key DS90CR562MTD specifications are a 4.5 V to 5.5 V supply range, 21 receiver inputs, three LVDS data streams, 18-bit color support, and a 48-pin TSSOP package. The manufacturer describes the device as an LVDS 18-bit color flat-panel display link receiver supporting FPD-Link and LVDS protocols. Its listed package is a 48-TFSOP with a 0.240 inch, 6.10 mm width, and the documented packaging method is Tube. Confirm operating temperature and timing limits against the manufacturer datasheet.
Where can I download the DS90CR562MTD datasheet PDF?
The DS90CR562MTD datasheet PDF is available from the Texas Instruments product documentation for the exact part number. The manufacturer’s official datasheet link is https://www.ti.com/lit/ds/symlink/ds90cr562mtd.pdf, while the National Semiconductor datasheet is also indexed through the public datasheet source at https://app2.alldatasheet.com/datasheet-pdf/pdf/8522/NSC/DS90CR562MTD.html. Use the manufacturer document for final pin, timing, and electrical-limit decisions.
Where can I find the DS90CR562MTD pinout?
The DS90CR562MTD pinout is found in the pin-description table and package drawing in the manufacturer datasheet. This device uses a 48-pin TSSOP package, so the complete pin list must account for pins 1 through 48 and any power or no-connect assignments shown in the official drawing. Do not assign PCB connections from an abbreviated distributor summary because the indexed search data does not reproduce the complete 48-pin table. The datasheet is the authoritative source for signal names, differential pairs, supply pins, ground pins, and no-connect positions.
Can DS90CR562MTD replace DS90CF562MTD?
DS90CF562MTD is the closest same-family replacement candidate identified for the DS90CR562MTD because both use the 48-TSSOP display-interface format and are listed for related LVDS/FPD-Link receiver applications. Compatibility still requires verification of every differential input, supply pin, clock connection, output mapping, and display timing parameter against the respective datasheets. The two parts should be treated as a qualified replacement only after the manufacturer’s pin descriptions and timing requirements have been compared.
What is the best drop-in replacement for DS90CR562MTD?
The best-supported drop-in replacement is DS90CF562MTD, provided its pinout and timing characteristics match the original board exactly. It belongs to the same National Semiconductor display-link family and uses the same 48-TSSOP package, making it the most relevant candidate for direct substitution. A valid replacement also requires matching supply voltage, receiver enable behavior, LVDS pair assignments, clock output, and panel timing. The alternatives list identifies several same-family candidates, but each must be checked against the exact schematic revision.
Is DS90CR562MTD suitable for a flat-panel monitor?
The DS90CR562MTD is suitable for a flat-panel monitor that uses the matching DS90CR561/DS90CR562 LVDS FPD-Link architecture and supports 18-bit color data. Its three LVDS data streams and parallel phase-locked clock transmission align with the documented display-link interface. The display timing, resolution, refresh rate, pixel-clock range, connector wiring, and panel input voltage must also be compatible. Because some of those detailed limits are not shown in the indexed technical summary, validate them against the manufacturer datasheet before production.
When should I choose DS90CR562MTD over another LVDS receiver?
Choose the DS90CR562MTD when the existing display design uses the National Semiconductor 21-bit CMOS/TTL-to-three-LVDS FPD-Link architecture, an 18-bit color path, and a 4.5 V to 5.5 V receiver supply. It is particularly appropriate when preserving an established 48-pin TSSOP PCB and its differential routing is more important than redesigning around a different receiver family. A different receiver should be selected when the panel uses another link standard, different signal count, incompatible clock architecture, or a different physical footprint.
What is the difference between DS90CR562MTD and DS90CR561MTD?
DS90CR562MTD is the receiver for the 18-bit color flat-panel display link, while DS90CR561MTD is the transmitter that converts 21 bits of CMOS/TTL data into three LVDS streams. The documented DS90CR561/DS90CR562 pair also sends the phase-locked transmit clock in parallel. They are complementary devices in the same display link and are not automatically interchangeable in a completed design, despite sharing the same 48-pin TSSOP package family.
What is the DS90CR562MTD supply voltage?
The DS90CR562MTD supply voltage range is 4.5 V to 5.5 V. According to the indexed DS90CR562MTD specification, the receiver operates across that nominal 5 V range. A PCB implementation should include local supply decoupling and should verify the exact absolute maximum and recommended operating conditions in the manufacturer datasheet, since those individual limits are not reproduced in the product-search summary.
How many LVDS data streams does DS90CR562MTD receive?
The DS90CR562MTD receives three LVDS data streams. The manufacturer family description states that 21 bits of CMOS/TTL data are converted into three LVDS streams at the transmitter, and the DS90CR562 receiver provides the corresponding receiver function. This arrangement supports 18-bit color display data while carrying the phase-locked transmit clock in parallel. Use the official differential-pair and pin tables when implementing the physical connection.
Is DS90CR562MTD in stock and what is the lead time?
Current stock and lead time should be requested through the Request a Quote form on this page. The indexed distributor results identify listings for the exact DS90CR562MTD ordering code, including Texas Instruments and Rochester Electronics inventory pages, but they do not provide a complete quantity-break price table or a dated lead-time statement. XAIPART’s request form is the appropriate channel for confirming current availability, minimum order quantity, packaging, and delivery timing.
Where can I buy DS90CR562MTD online?
Use the Request a Quote form on this page to request DS90CR562MTD availability, packaging, and lead time from XAIPART. The exact part is listed in the indexed product results as a 48-TSSOP interface IC, and the Tube packaging format is identified in the technical specification summary. Because inventory and commercial terms can change rapidly, request a current quotation rather than relying on a static listing status or an unverified price.
What is the price of DS90CR562MTD?
Request the current DS90CR562MTD price through the Request a Quote form on this page. The indexed product pages do not expose an explicit quantity-break price for the exact ordering code with a verifiable quantity beside each amount, so no static price value is reproduced in this record. A quotation also allows confirmation of the 48-TSSOP package, Tube packaging, minimum order quantity, current lifecycle status, and expected delivery schedule.
Does DS90CR562MTD require a separate LVDS clock?
The DS90CR561/DS90CR562 link description states that a phase-locked transmit clock is transmitted in parallel alongside the three LVDS data streams. The DS90CR562 therefore supports a parallel clock path as part of the intended family architecture. The exact clock input or output direction and its timing relationship must be confirmed from the pin-description and timing diagrams in the manufacturer datasheet, because the abbreviated product listing does not provide the complete pin table.
What is the DS90CR562MTD package type?
The DS90CR562MTD is packaged in a 48-pin TSSOP, also described in the technical listing as a 48-TFSOP measuring 0.240 inch, or 6.10 mm, in width. Its listed packaging method is Tube. The package key for this record is tssop-48 because the verified results identify the component as a 48-pin TSSOP interface IC.
Can DS90CR562MTD be used in an industrial display system?
The DS90CR562MTD can be used in an industrial display system when the system already uses the matching DS90CR561/DS90CR562 FPD-Link interface and compatible 18-bit display timing. Its 4.5 V to 5.5 V supply range and dedicated LVDS receiver role fit panel-control systems that use serialized differential signaling. Industrial suitability still depends on the exact temperature grade, EMC requirements, display timing, and panel interface, which should be checked against the current manufacturer documentation.

Engineering reference data for DS90CR562MTD — comparison, design guidance, and compliance information.

Selection Guide

Choose DS90CR562MTD when maintaining an established National Semiconductor DS90CR561/DS90CR562 flat-panel display link, particularly an 18-bit color design using three LVDS streams, a parallel phase-locked clock, and a 4.5 V to 5.5 V receiver rail. Its 48-TSSOP package supports board reuse without a footprint change. Evaluate DS90CF562MTD first for a related receiver-family substitution, but compare every pin and timing parameter. DS90CR213MTD may be useful when reviewing another National Semiconductor display-interface architecture, though its protocol and signal mapping require confirmation. DS90CR561MTD and DS90CR561AQT are transmitter choices rather than receiver replacements; they fit the opposite end of the link. DS90CR562AQT is a revision-related receiver candidate whose device marking, timing, and production status should be checked. For any substitution, require direct verification of differential pairs, clock direction, supply pins, enables, no connects, panel timing, and environmental limits.

Comparison with Alternatives

Parameter This Product DS90CF562MTD DS90CR213MTD DS90CR561MTD DS90CR561AQT DS90CR562AQT
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 48-TSSOP 48-TSSOP 48-TSSOP 48-TSSOP 48-TSSOP 48-TSSOP

Key Differentiators

  • Receiver role matches the DS90CR561 transmitter direction (vs DS90CR561MTD)
  • Documented 48-pin TSSOP footprint with 48-TFSOP package listing (vs DS90CR213MTD)
  • Same-family receiver candidate with shared display-link architecture (vs DS90CF562MTD)
  • 18-bit color FPD-Link positioning (vs DS90CR213MTD)

Design Notes

Route each LVDS differential pair as a controlled-impedance pair over a continuous reference plane. Keep the two traces of a pair at equal length, avoid stubs and test-point discontinuities, and use the manufacturer’s recommended input termination and layer-transition geometry. The DS90CR562MTD receives three LVDS data streams, so pair-to-pair skew and connector transitions must be checked together rather than treating the link as ordinary parallel routing.

Place the receiver and its local supply-decoupling network close to the display connector and LVDS trace endpoints. The documented operating range is 4.5 V to 5.5 V, so follow the manufacturer’s recommended capacitor values and placement for the 5 V rail rather than treating the receiver as a generic digital IC. Keep noisy switching-regulator and processor return currents out of the immediate receiver ground path, and verify the pin table before assigning supply and ground connections.

Do not assume that every 48-TSSOP DS90CR-family device is interchangeable. DS90CR561MTD and DS90CR562MTD are complementary transmitter and receiver devices, while DS90CF562MTD and DS90CR213MTD may differ in protocol details, pin function, timing, or supply requirements. Before substitution, compare all 48 positions, differential pair assignments, clock direction, enable behavior, no-connect pins, absolute maximum ratings, and panel timing against the manufacturer datasheets.

Confirm the receiver’s supply tolerance, current consumption, power-up sequence, and clock stability against the current manufacturer datasheet before finalizing the 5 V distribution network. If the nearby transmitter or display controller has a different power-up order, use the specified sequencing controls to avoid invalid pin states and startup transients. Do not infer power behavior solely from the 4.5 V to 5.5 V operating-range summary.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The indexed product results do not state exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm compliance for the exact ordering code and current manufacturer documentation before release.

Data verified on: 2026-11-10 — data verified and curated by XAIPART's component engineering team

Related Searches

DS90CR562MTD datasheet DS90CR562MTD pinout DS90CR562MTD datasheet pdf DS90CR562MTD specifications DS90CR562MTD equivalent DS90CR562MTD replacement DS90CR562MTD cross reference DS90CR562MTD price DS90CR562MTD stock Texas Instruments DS90CR562MTD DS90CR562MTD 48-TSSOP DS90CR562MTD LVDS receiver DS90CR562MTD flat panel interface DS90CR562MTD vs DS90CF562MTD DS90CR562MTD application circuit

Related Components & Terms

Texas Instruments National Semiconductor DS90CR562MTD DS90CR561MTD DS90CF562MTD DS90CR213MTD DS90CR561AQT DS90CR562AQT LVDS receiver LVDS transmitter FPD-Link Low Voltage Differential Signaling CMOS/TTL data 18-bit color display phase-locked transmit clock 48-TSSOP 48-TFSOP surface mount flat-panel display industrial monitor video interface differential signaling digital interface IC
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details